Saramonic 121401B Wireless Lavalier Microphone User Manual

: June 6, 2024
: Saramonic

Table of Contents

Statement
Cautions
General Introduction
Product Structure
Accessory Setup Guide
Operation Guide
Specifications
Packing List
FCC Statement
ISED Statement
Customer Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Saramonic 121401B Wireless Lavalier Microphone User Manual

Statement

Please read this manual carefully before using and strictly operate and store in accordance with the instructions. Please save it for your future reference.

If the user manual can not help you to solve certain problems, please ask your retailer for help or email us: [email protected].

Cautions

Please do not dismantle the outer case.
Don’t place this unit close to heat sources such as heater, oven, or other devices that produce heat.
Please do not replace the battery on your own.
Only use a soft, dry cloth to clean the product.
When using and storing, please pay attention to dust and moisture

General Introduction

The BTW is a compact and portable wireless lavalier microphone. It features an omnidirectional microphone capsule, which delivers clear and intelligible sound. The BTW can work i tandem with third-party apps for audio/video recording. It is compatible with both iOS and Android devices. With an operating range of up to 80m, the BTW is ideal for content creation, live streaming, interviews, online class, etc.

Product Structure

Power Button
Function| Operation
---|---

Power ON

|

Press and hold the button for 2 seconds

Power OFF

|

Press and hold the button for 3 seconds

Play/Pause

|

Short press the button (successfully connected)

Clear Pairing Records

|

Make sure the BTW is turned off.
Then press and hold the button for 5 seconds.

Status Indicator

Mode

|

Indicator

---|---

Unpaire

(wait for pairing)

|

Blinks blue 3 times, then ﬂashes blue and green alternately (If not connected within two minutes, the unit will enter standby mode.)

Standby Mode

|

Slow ﬂashing green light

Power OFF

|

Green light blinks 3 times

Paired Successfully

| Slow ﬂashing blue light
Low Battery|

Voice prompts “Low Battery” every two minutes

Charging

| Solid green light
Fully Charged|

Light up blue for 2s, then ﬂashes green slowly

3.5mm Headphone Jack
Connect the supplied single earbud for audio monitoring.
Built-in Microphone
USB Type-C Charging Port
Belt Clip (Detachable)
Magnetic Cli p

Accessory Setup Guide

Operation Guide

Press and hold the power button for 2 seconds to turn on the BTW.
Pairing.

First time pairing:
The BTW will enter pairing mode automatically after power on. The indicator flashes blue and green alternately.
Turn on Bluetooth, then select “Saramonic BTW” on your device.
When connected successfully, the indicator flashes blue slowly.
Automatic connection:
Turn on the Bluetooth of the last device connected, and then turn on the BTW, the connection between the device and the BTW with will be automatically established.
Open a third-party audio or video app and start recording.

For better recording experience, the application SmartRecorder is recommended.
Please scan the following QR code to download and install

Smart Recorder.

Specifications

Transmission Type

| 2.4GHz wireless transmission
---|---
Modulation|

GFSK

Operating Range

| 80m (line-of-sight)
RF Output Power|

<10dBm

Polar Pattern

| Omnidirectional
Maximum SPL|

120dB SPL

Sensitivity

| -42dB
Power Requirement|

Built-in Li-ion Battery

Charging Port

| USB Type-C
Battery Life|

10 hours

Antenna

| Built-in Antenna
Audio Connector|

3.5mm headphone jack (stereo output) (also support TRRS microphone input)

Dimensions

| 67.6×42.6×18.4mm
Weight|

24.5g

Operating Temperature

| 0°C to 50°C
Storage Temperature|

–20°C to 55°C

Packing List

1×BTW Wireless Lavalier Microphone
1×USB-A to USB-C Charging Cable
1×Single Earbud
1×Fur Windshield
1×Belt Clip

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
The device has been evaluated to meet general RF exposure requirement. This equipment should be installed and operated with minimum distance 0mm between the radiator & your body.

ISED Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).

The device has been evaluated to meet general RF exposure requirement. This equipment should be installed and operated with minimum distance 0mm between the radiator & your body.