AUMAPF00001 Electrical Actuator Installation Guide
- June 6, 2024
- auma
Table of Contents
AUMAPF00001 Electrical Actuator
Introduction
The module with the associated PCB antenna is specially designed for various expansion stages of the PROFOX electric actuator. The antenna in particular is adapted for the installation position in the housing. For this reason, it is necessary to adhere to the installation specifications. The following steps describe the integration of the module and the associated antenna.
Installation specifications
Integration steps
-
The module must be pushed completely into a plastic carrier for a fixed position (see Figure 1)
-
The Antenna Z135.074 must be pushed into the screw plug Z136.746 screwed into a metal housing (see Figure 2)
-
After integrating the module Z123.664 and Z135.074, the 120 mm antenna cable must be connected to the U.FL Connector on the module and the complete plastic carrier ist pushed in a metal housing (see Figure 3)
-
The plastic carrier must be pushed down completely (see Figure 4)
-
The regulations were only checked with a completely closed metal housing. (see Figure 5)
Regulatory Notices
FCC/IC Notice English
This device complies with Part 15 of the FCC Rules [and with Industry Canada licence-exempt RSS standard(s)].Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Safety instructions (English)
| Changes or modifications made to this equipment not expressly approved by
AUMA Riester GmbH & Co. KG may void the FCC authorization to operate this
equipment!
---|---
| This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the operation instructions, may cause harmful
interference to radio communi-cations. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his or her own expense!
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and usedin accordance with the operation instructions, may cause harmful interference to radio communi-cations. Operation of this equipment in a residential area is likely to cause harmful interference inwhich case the user will be required to correct the interference at his or her own expense!
FFC Labelling (USA)
The End User must ensure that FCC labeling requirements are met. This includes
a clearly visible label on the outside of the Endproducts enclosure
specifiying the appropriate AUMA FCC identifier for this module.
The FCC identifier is FCC ID: 2A2OUAUMAPF00001
This FCC identifier is valid for the Z123.664 Module. The end product must in
any case be labelled on the exterior with: “Contains FCC ID:
2A2OUAUMAPF00001”
ISED Labelling (Canada)
The End User must ensure that FCC labeling requirements are met.
This includes a clearly visible label on the outside of the Endproducts
enclosure specifiying the appropriate AUMA FCC identifier for this module.
The IC identifier is IC: 27543-AUMAPF00001
This IC identifier is valid for the Z123.664 Module. The end product must in
any case be labelled on the exterior with: “Contains FCC ID:
2A2OUAUMAPF00001”
European Conformity
The electric actuator complies, with regard to the Bluetooth module used, with
the following standards in compli-ance with the RED (2014/53/EU) articles:
EMC: EN 301489-1
V2.2.1
EN 301489-17
V3.2.0
Radio:
EN 300328 V2.2.2