7RYMS D11059B RimoMic Lite UC Streaming and Video Mini Wireless Microphone User Manual
- June 6, 2024
- 7RYMS
Table of Contents
7RYMS D11059B RimoMic Lite UC Streaming and Video Mini Wireless
Microphone
Foreword
Thanks for purchasing 7RYMS RimoMic Lite UC Mini Wireless Microphone (For
USB-C & USB-A Interface )
To ensure bring you a good using experience, please read this manual book
carefully before using and correctly install and operate.
Main Features
- Mini Wireless Microphone, Delicate and Portable
- Wireless Working Range up to 30m
- Support Real-time Monitor for Both PC&MIC
- Intuitive Visual Power and Volume Monitor
- Adjustable Volume, Low Cut Filter
- Auto Pair & IR Sync, Efficient and Convenient
- Built-in Rechargeable Lithium Battery, USB-C Charging Port
Notice
- Please make sure the IR sensor are closely aligned when pairing
- This product belongs to high-precision instruments, please avoid falling, collision or pounding
- Do not use this equipment in the vicinity of heat source or interference source, such as radiator, oven, refrigerator or air conditioner, smartphone or next to the WIFI AP
- If the pick-up distance is close or when used outdoors, please put on the wind muff to prevent sound burst or reduce wind noise
- Do not use the equipment in rain or in a damp environment to avoid short-circuit danger
- Please keep the product in a dry environment
Packing List
Main Parts:
Accessories:
- USB C-USB A Adapter
- Wind Muff
- Charging Cable
- Carry Case
- User Manual
- Warranty Card
Components Introduction
Transmitter(TX):
- Internal Mic
- Power/Low Cut Filter Indicator Light
- Audio Status Indicator Light
- Volume+
- Volume-
- Power/Low Cut Filter Button
- Belt Clip
- IR Sensor
- USB-C Charging Port
Receiver (RX)
- IPS Display Screen
- USB-C Plug
- IR Sensor
- Pairing Button
- 3.5mmTRS/TRRS Monitor Interface
Installation and Operation
Transmitter(TX):
Install the transmitter on the collar through the belt clip so that the
internal microphone points in the direction of the sound source For better
hiding during use, it is recommended that the belt clip be fixed and used
outwards
Receiver (RX)
-
Work with Smartphone:
Install the receiver to the mobile phone with USB-C interface through the USB-C plug. -
Work with Computer:
-
For computer with USB-C port, insert the receiver into the computer USB-C port;
-
For computer with USB-A port, insert the receiver into the USB C-USB A adapter; Then insert the USB C-USB A adapter into the computer USB-A port
-
Pairing:
After installing the receiver on the smartphone or computer, keep the receiver and transmitter’s IR sensor closely aligned for paring
Function and Usage
Transmitter (TX):
-
Internal Mic
Point the internal Mic at the sound source to record -
Power/Low Cut Filter Indicator Light
Blue light keeps on after turn on the Transmitter; Purple light keeps on after turn on Low Cut Filter mode; Red light flicker when pairing or low power; Red light keeps on when charging -
Audio Status Indicator Light
Blue light flicker when sound is input; Red light keeps on when sound is crackled -
Volume+ Volume-
Short press to adjust the microphone’s volume -
Power/Low Cut Filter Button Long press to turn on/off; short press to switch low cut
-
USB-C Charging Port
Connect the transmitter and 5V power supply through the USB A- USB C charging cable for charging -
IR Sensor
It’s paired successfully only when the receiver and transmitter’s IR sensor are closely aligned
Receiver (RX):
-
IR Sensor
It’s paired successfully only when the receiver and transmitter’s IR sensor are closely aligned -
Pairing Button Long press to pair
-
3.5mm TRS/TRRS Headphone Monitor Port Insert 3.5mm TRS/TRRS headphones to monitor
Screen Display Instruction:
This device operates on a no-interference, no-protection basis. Should the user seek to obtain protection from other radio services operating in the same TV bands, a radio licence is required. For further details, consult Innovation, Science and Economic Development Canada’s Client Procedures Circular CPC-2-1-28, Voluntary Licensing of Licence-Exempt Wireless Microphones in the TV Bands.
Email: support@7ryms.com
The 7RYMS LOGO is trademark which is registered and owned by Errun Electronic
Technology Co., Ltd
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2)
this device must accept any interference received, including interference that
may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure condition without restriction.
ISED Statement
‐ English: This device complies with Industry Canada license‐exempt RSS
standard(s). Operation is subject to the following two conditions: (1) This
device may not cause interference, and (2) This device must accept any
interference, including interference that may cause undesired operation of the
device.
The digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B).
For Receiver:
This device meets the exemption from the routine evaluation limits in section
2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain
Canadian information on RF exposure and compliance.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
For Transmitter:
This device meets the exemption from the routine evaluation limits in section
2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain
Canadian information on RF exposure and compliance.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0mm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>