7RYMS B0BFVMLVWB iRay DW20 2.4G Dual-Channel Wireless Microphone User Manual
- October 30, 2023
- 7RYMS
Table of Contents
7RYMS B0BFVMLVWB iRay DW20 2.4G Dual-Channel Wireless Microphone User Manual
Foreword
Thanks for purchasing 7RYMS iRay DW20
Main Features
- 2.4G Dual-channel Wireless Microphone, Global Free Frequency
- 48kHz/24bit Audio Recording, Intelligent Denoise
- Support Digital & Analog Output Mode, Universal for Phone, Computer and Camera
- Mono/Stereo/Safety Mode for Ultimate Flexibility in Post-production
- LCD Screen for Intuitive Power and Audio Dynamic Monitor
- Preamp Amplifier and 12-level Adjusted Gain Control
- Real-time Audio Monitor and Mute Function
- Internal and External MIC Two Input Modes
- Low Latency < 20ms, Working Range Up to 100m(Open Environment)
- Designed with Multi-functional Belt Clip and Compact
Notice
⚠ Due to 2.4G wireless characteristics, it is better to keep face to face when
use it, and do not turn your back to the receiver, otherwise it is easy to
generate breakpoints, which is a normal phenomenon
⚠ Do not block the antenna position to avoid any poor signal generated
⚠ Please attention that it can not realize STEREO function when in single-
channel and safety mode
⚠ The product belongs to high-precision instruments, please avoid falling,
collision or pounding
⚠ Do not use the equipment in the vicinity of heat source or interference
source, such as radiator, oven, intercom or next to the other wireless devices
⚠ If the pick-up distance is close or when it is used outdoors, please put on
the wind muff to prevent sound burst or reduce wind noise
⚠ Do not use the equipment in rain or in a damp environment to avoid short-
circuit danger
Packing List
-
Transmitter(TX)
-
Receiver(RX)
-
3.5mm TRS Mic Audio Input Cable
-
Wind Muff
-
3.5mm TRS-TRS Audio Cable
-
3.5mm TRS-TRRS Audio Cable
-
3 in 1 Charging/Output Cable
(The orange cable can be used for charging and digital output, the black cable can only be used for charging ) -
Carry Case
-
User Manual
-
Warranty Card
Purchase Options:
iRay DW20 (A)
①x2+②+③x2+④x2+⑤+⑥+⑦+⑧+⑨+⑩
iRay DW20 (B)
①+②+③+④+⑤+⑥+⑦+⑧+⑨+⑩
Components and Instruction
Transmitter(TX) Components:
Function Introduction:
- 3.5mm TRS Port of External Mic: Insert the 3.5mm TRS Mic Audio Input Cable, and you can use the external lavalier microphone for recording. At this time, the internal microphone of the device is turned off automatically
- Power Button: Long press for On/Off
- Muting Button: Long press to switch between normal recording and mute
- Pair Button: Long press for pairing with the receiver
- USB-C Charging Port: Connect the transmitter with the power through 3 in 1 charging/output cable to charge
- Reset Hole: If there is an abnormal phenomenon such as the device is crash or unable to turn on, insert the reset pin into the reset hole to reset it
Screen Display:
Receiver(RX) Components:
Function Introduction:
- 3.5mm TRS/TRRS Monitoring Port: Plug in 3.5mm TRS/TRRS headphones to monitor; When monitoring in Stereo mode, A is the left channel and B is the right channel
- 3.5mm TRS Audio Output Port: Output a mixed audio track in Mono mode; Output two independent audio tracks in Stereo mode; Output two mono audio in Safety mode: One is normal audio, and the other is safe audio reduced by -6dB on the basis of normal audio
- A/B Channel Output Volume Control Button: Short press to cyclically adjust the A/B channel output volume. In the mono mode, the A/B channel output volume is adjusted synchronously
- USB-C Charging/Output Port: Connect the receiver and the corresponding device through the 3-in-1 charging/output cable for charging or digital output
- Power/Mono/Stereo/Safety Mode Switch Button: Long press for On/Off; Short press for Mono/Stereo/Safety mode switch; It can not realize STEREO function when in single-channel and safety mode
- Reset Hole: If there is an abnormal phenomenon such as the device is crash or unable to turn on, insert the reset pin into the reset hole to reset it
Screen Display:
Installation and Usage
Pairing Method
Turn on the transmitter, long press its pair button to pair. The first paired
transmitter is channel A (left channel), and the second one is channel B
(right channel)
Installation Method: Transmitter(TX)
Choose internal/external mic according to personal needs
Internal Mic
- For better concealment during use, it is recommended that the belt clip is fixed on the outside for use
- When the external microphone is working, the internal microphone will be automatically turned off
When using the internal mic, install the wind muff according to personal
needs; Insert the wind muff into the locking buckle, and then tighten it
clockwise
Receiver(RX)
-
Work with Camera
Fix the receiver through the belt clip to the camera’s cold shoe mount; Connect the receiver with camera through the 3.5mm TRS-TRS audio cable; Choose whether to monitor according to personal needs
-
Work with Smartphone/Computer Connect the receiver with smartphone/computer through the 3.5mm TRS-TRRS audio cable and related audio adapter cables; Choose whether to monitor according to personal needs(Please purchase related audio adapter cables by yourself)
Specifications
https://linktr.ee/7ryms_official?utm_source=qr_code
Website: 7ryms.com
Facebook: 7RYMS
Instagram: 7ryms_official
YouTube: 7RYMS
The 7RYMS LOGO is trademark which is registered and owned by Errun Electronic Technology co., Ltd