KUSTOM ProLaser 4 Portable LIDAR Speed Measurement User Guide
- June 6, 2024
- Kustom
Table of Contents
ProLaser 4 Quick Reference Guide
ProLaser 4 Rear Panel Controls and Display
Head-Up Display
| Single Press|
Press and Hold
---|---|---
| Rear Display Brightness| Power On/Off
| HUD Brightness (Poor Weather in Menu)| Poor Weather Mode
| Menu|
| Mode Up (In Menu)| Receding Only Targets
| Volume Down (In Menu)| Volume Down (In Menu)
| Display Lock (Enter button in Menu) Mark Select Events (Option)| Self-Test
First Time Operation
- Install 4-AA batteries in the Battery Compartment, or plugin USB.
- Press and hold the power button to power on/off.
- Hold the unit by the pistol grip and aim through the HUD, with both eyes open.
- Press and hold the trigger to fire the laser.
- Place the aiming reticle on the target vehicle. Continue target tracking through the HUD.
- While holding the trigger down, Speed and Range continually update in the HUD and on the rear display.
- Audio tones provide targeting feedback. A solid tone indicates the target successfully acquired.
- Release the trigger to lock the measurement in the HUD and rear panel display.
The ProLaser 4 will enter (default) sleep mode after two (2) minutes and will power down after 15 minutes. Sleep timers are adjustable.
Recall Events
- Press the Menu button.
- Select Events.
- Use the up/down buttons to scroll through up to 100 previous measurements on the rear panel.
Download Events Data
ProLaser 4 allows the user to download measurements over the USB to a spreadsheet using a PC utility. The utility may be downloaded from the Kustom website from the ProLaser 4 product and Service pages.
The Events data includes Speed & Range measurements with date & time, units, tracking history time, and serial number as shown below.
Date| Time| Speed| Units| Range| Units|
Track| Units| S/N
---|---|---|---|---|---|---|---|---
9/2/2021| 12:39:41| 79| mph| 242| ft| 3.6| sec| 22155
9/2/2021| 12:39:11| 65| mph| 2446| ft| 1.7| sec| 22155
9/2/2021| 12:38:47| 92| mph| 687| ft| 15.1| sec| 22155
9/2/2021| 12:38:14| 70| mph| 494| ft| 12| sec| 22155
9/2/2021| 12:36:39| 67| mph| 272| ft| 2.3| sec| 22155
9/2/2021| 12:36:16| 68| mph| 192| ft| 15.9| sec| 22155
ProLaser 4 Menus
The menu button accesses the following settings or modes:
Distance
Sets min/max range limits to target vehicle for school and work zone
enforcement. Fire the LASER at the desired target or use up/down arrows to
enter values. Press enter to set min/max ranges. Any target measured outside
the range limits will not be displayed.
Set Direction
Sets target direction discrimination to Approaching only, Receding only, or
Both.
DIF-TEST
Two-target, differential distance accuracy test mode.
Continuous/Single
Sets enforcement mode to continuous target measurement or single-shot mode
(option).
Units
Select between mph/km/h; mph/knots; or km/h/knots (option).
HUD Options
Toggle Range in HUD on/off. Select from four aiming reticles.
Events
Displays last 100 locked targets with Speed, Range, and Direction with the
date and time stamp.
Set Time/Date
Set date and time in 24-hour format (option).
Stopwatch
Average speed over distance enforcement mode (option).
Accuracy Tests
Self-Test
Press the test button to run internal accuracy tests.
HUD Alignment Test
Place the ProLaser 4 in range mode. Select an isolated target ~100 feet
away and sweep HUD horizontally and vertically across the target. Listen for
audio tone and verify aiming reticle on target coincides with tone and range
measurement in HUD.
Differential Distance Test
Select two targets ~ 50 and 100 feet away. Target each when prompted and
verify range accuracy.
9652 Loiret Boulevard,
Lenexa, KS 66219-2406
(800)4KUSTOM
800-458-7866
www.kustomsignals.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>