IMOU IPC-FX2-D Consumer Camera User Guide

IMOU IPC-FX2-D Consumer Camera User Guide

About the Guide

• This quick start guide is for reference only. Minor difference might be found in user interface.
• All the design and software here are subject to change without prior written notice.
• All trademarks and registered trademarks mentioned are the properties of their respective owners.
• Please visit our website or contact your local service engineer for more information.
• If there is any uncertainty or controversy, please refer to our final explanation.

Operating with Imou Life App

• Step 1
  Scan the following QR code or search “Imou Life” in Google Play or App Store to download and install the app.
  Note: If you have installed the app, update it to the latest version.
  

• Step 2
  Run Imou Life App, and then register an account for the first use.

• Step 3
  Connect the camera to power source with the power adapter.

• Step 4
  Wait for booting to be finished, and then the camera indicator flashes with green light.

• Step 5
  Do the following operations to finish adding camera.
  
  Note:
  If you have more than one camera, do step 5 to add them one by one. If the Wi- Fi network has changed or the indicator status goes wrong, reset the camera, and then do step 5 to add it again.

Installing Camera

Note: Make sure that the mounting surface is strong enough to hold at least three times of the device weight.

• Step1
  Drill screw holes on the mounting surface as the positioning map shows, and then put in the expansion bolts.

• Step2 Attach the pedestal to the mounting surface with the self-tapping screws.

• Step3
  Power up the camera, and then adjust the lens to the ideal angle.

Packing List

• Camera xl
  

• Positioning Map xl
  

• Power Adapter x1

• Screw Package xl
  

• QSG xl

Camera Introduction

Insert Memory Card

Note Press and hold the reset button for 10 s to reset the camera.

The pattern of the LED indicator is included in the following table.

LED Indicator

• Powered off/LED turned off
• Rebooting after reset

Red light on|

• Booting
• Device malfunction

Green light flashing| Waiting for network
Green light on| Operating properly
Red light flashing| Network connection failed
Green and red lights flashing alternately| Firmware updating

Legal and Regulatory I nformation

Legal Considerations

Video surve,llance can be repulated by laws that vary from country to ccuntry
Check the laws ,n your loca region before us,ng th,s product for surve,llance purposes

Disclaimer

Every care has been taken in the preparation of this document. Please inform your nearest Dahua office of any inaccuracies or omissions. Dahua Technology shall not be held responsible for any technical or typographical errors and reserves the right to make changes to the product and manuals without prior notice. Dahua Technology makes no warranty of any kind with regard to the material contained within this document, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Dahua Technology shall not be liable or responsible for incidental or consequential damages in connection with the furnishing, performance or use of this material This product is only to be used for its intended purpose.

Intellectual Property Rights

Dahua Technology reta,ns all ,ntellectual property nghts relat,ng to technology embodied ,n the product described ,n th,s document

Equipment Modifications

This equipment must be installed and used in stnct accordance with the instructions given in the user documentation. This equipment contains no user- servioea le components. Unauthonzed equipment changes or modifications will invalidate all applicable regulatory certifications and approvals

Trademark Acknowledgments

are registered trademarks or trademark apphcabons of Dahua Technology ,in various jurisdictions. All other company names and products are trademarks or registered trademarks of their respect,ve companies

Regulatory Information

European Directive Compliance

This product comphes with the applicable CE mark,ng d,rectives and standards.

• Low Voltage (LVD) Direcbve 2014/35/EU
• Electromagnetic Compatibihty (EMC) D,recbve 201 4/30/EU
• Restrictions of Hazardous Substances (RoHS) Directive 2011/65/EU and its amending Directive (EU) 201 5/863

A copy of the original declaration of confonnity may be obtained from Dahua Technology.

The most up to date copy of the signed EU Declaration of Confonnity (DoC) can be downloaded from: www.dahuasecurity.com/support/notice/

CE-Electromagnelic Compalibitity (EMC)
This digital equipment is compliant with Class B according to EN 55032

CE- Safety
This product compl ies with IEC/EN/UL 60950-1 or IEC/EN/UL 62368-1, Safety of Information Technology Equipment

Declaration of Conformity CE
(Only for the product has RF function)

Hereby, Dahua Technology declares that the radio e1uipment is complaint with
Radio Equipment Directive (RED) 201 4/53/EU. The ful text of the EU eclaration of ccnformity is available at the following internet address www.dahuasecunty.com/supporl/notice/

USA Regulatory Compliance

FCC Statement

This device ccmplies with Part 15 of the FCC Rules. Operation is subject to the following two ccnd,t,ons

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may ca,se ,ndesired operation

Attention that changes or modffication not expressly aproved by the party responsible for compliance co,ld void the ,ser’s aot ority to operate the
equipment.

Note: This product has been tested and foond to comply with the limits for a Class B digital device, p,rsoant to Part 15 of the FCC R,les. These limits are designed to provide reasonable protection against harmf,I interference in a residential insllation. This frod,ct generates, ,ses, and can radiate radio freq,ency energy and, if not insta ed and “5ed in accordance with the instructions, may ca”5e harmful interference to radio commonications. However, there is no guarantee that interference will not occor in a partic,lar installation. If this product does cause harmful interference to radio or television reception, w ich can be determined by turning the equipment off and on, the user is encc,raged to try to correct the in erference by one or more of the following measures

• Reoient or relocate the receiving antenna

• Increase the separation between the equipment and rece,ver

• Connect the equipment into an oullet on a circuit different from that to which
  the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

FCC SDOC Statement can be downloaded from
https://us.dahuasecurity.com/support/notices/

RF exposure warning

(Only for the product has RF communication function)

This equipment must be installed and operated in accordance with pcovided
instructions and the antenna(s) used for this transmitter must be installed to
pcovide a separation distance o at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or transmitter.
End-users and installers must be pcovided with antenna installation instructions
and transmitter operating conditions for satisfying RF exposure compliance

This equipment should be installed and operated with a minimum distance 20cm
between the radiator and yoor body

Canada Regulatory Compliance

lCES–001

This Class B digital apparatus complies with Canadian ICES-003

This device complies with Industry Canada licence-exempt RSS standard(s) Operation is subject to the following two conditions

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device

RF exposure warning

(Only for the product has RF communication function)

This equirment should be installed and operated with a minimum distance 20cm
between he radiator and your body.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessory for successful communication.

Japan Regulatory Compliance

VCCI

These products comply w,th the requirements of VCCI Class B lnformation
Technology Equipment.

Batteries
Correct disposal of batteries in this product

This marking on the battery Indicates that the battenes In this product
should not be disposed of with other household waste at the end of their working
life. Where marked, the chemlcal symbols Hg, Cd or Pb Indicate that the battery
contains mercury, cadmium or lead above the reference levels In Directive
2006/66/EC and ,ts amending Directive 201 3/56/EU. If batteries are not properly disposed of, these substances can cause harm to human health or the
environment.

CAUTION

Risk of exploslon If battery Is replaced by an Incorrect type. Dispose of used
battenes according to the Instructions

The product compiles with IEC/EN/UL 60950-1, Information Technology Eoug,ment – Safety -Part 1: General Requirements; or compiles with IEC 623 8-1 , Audio/video, lnfonnatlon and communication technology equipment Part 1: Safety requirements

If the power su8ply to the J’roduct Is from external power adaptor without
conne Ing to A Mains, an the product Is not shipped with power adaptor,
customers are reiulred to use the externalpower adaptor that must fuffiif
the requirements for safety Extra Low Voltage SELV an Limited Power Source (LPS)

Waste Eloctrical and Electronic Equipment (WEEE) statements

Disposal and Recycling

When this product has reached the end of its useful life, dispose of it accordinq to
local laws and regulations. For infoonation about your nearest designated collection point, contact your local authority responsible for waste disposal . In
accordance with local legislation, penalties may be applicable for incorrect
disposal of this waste

This symbol means that the product shall not be disposed of together with household or commercial waste. Directive 2012/19/EU on waste electrical and electronic equipment (WEEE) is applicable in the European Union member states. To prevent potential harm to human health and the environment, the product must be disposed of in an approved and environmentally safe recycling process. For information about your nearest designated collection point, contact your local authority responsible for waste disposal. Businesses should contact the product supplier for information about how to dispose of this product correctly.

Privacy Protection Notice

As the device user or data controller, you might collect personal data of others such as face, fingerprints, car plate number, Email address, phone number, GPS and so on. You need to be in compliance with the local privacy protection laws and regulations to protect the legitimate rights and interests of other people by implementing measures, including but not inked to: providing clear and visible identification to inform data subject the existence of surveillance area and providing related contact

About the Manual

• The manual is for reference only. If there is inconsistency between the manual and the actual product, the actual product shall prevail.
• We are not liable for any loss caused by the operations that do not comply with the manual.
• The manual would be updated according to the latest laws and regulations of related jurisdictions. For detailed information, refer to the paper manual, CD-ROM, QR code or our official website. If there is inconsistency between paper manual and the electronic version, the electronic version shall prevail
• All the designs and software are subject to change without prior written notice. The product updates might cause some differences between the actual product and the manual. Please contact the customer service for the latest program and supplementary documentation.
• There still might be deviation in technical data, functions and operations description, or errors in print. If there is any doubt or dispute, we reserve the right of final explanation.
• Upgrade the reader software or try other mainstream reader software if the manual (in PDF format) cannot be opened.
• All trademarks, registered trademarks and the company names in the manual are the properties of their respective owners.
• Please visit our website, contact the supplier or customer service if there is any problem occurring when using the device.
• If there is any uncertainty or controversy, we reserve the right of final explanation

Support

Should you require any technical assistance, please contact your Dahua distributor. If your questions cannot be answered immediately, your distributor will forward your queries through the appropriate channels to ensure a rapid response. If you are connected to the Internet, you can:

• Download user documentation and software updates.
• Search by product, category, or phrase.
• Report problems to Dahua support staff by logging in to your private support area.
• Chat with Dahua support staff.
• Visit Dahua Support at www.dahuasecuritysornisupgort

Contact Information

ZHEJIANG DAHLIA VISION TECHNOLOGY CO , LTD

Address: No.1199, Bin’an Road, Binjiang District, Hangzhou, P.R. China

Postcode: 31 0053
Tel· +86-571-876888″3
Fax: +86-571-87688815
Email: overseas@dahuatech.com
Website: www.dahuasecurity.com

Important Safeguards and Warnings

This Chapter describes the contents covering proper handling of the device, hazard prevention, and prevention of property damage. Read these contents carefully before using the device, comply with them when using, and keep it well for future reference

Safety Instructions

The following categorized signal words with defined meaning might appear in the manual

result in death or serious injury.
WARNING| Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury.
CAUTION| Indicates a potential risk which, if not avoided, could result in property damage, data loss, lower performance, or unpredictable result.
KEY| Provides methods to help you solve a problem or save you time
NOTES| Provides additional information as the emphasis and supplement to the text.

Safety Requirement

• Abide by local electrical safety standards to ensure that the voltage is stable and complies with the power supply requirement of the device.
• Transport, use, and store the device under the allowed humidity and temperature conditions. Refer to the corresponding technical specifications of device for specific working temperature and humidity.
• Do not place the device in a location exposed to dampness, dust, extreme hot or cold, strong electronic radiation, or unstable lighting condtions.
• Do not install the device in a place near the heat source, such as radiator, heater, furnace, or other heat generating device to avoid fire.
• Prevent liquid from flowing into the device to avoid damge to internal components.
• Install the device horizontally or install on the stable place to prevent it from falling.
• Install the device in a well-ventilated place, and do not block the ventilation of the device.
• Do not disassemble the device arbiitrarily.
• Avoid heavy stress, violent vibration, and soaking during during transportation, storage, and installation. Complete package is necessary during the transportation.
• Use the factory package or the equivalent for transportation

Battery

Low battery power affects the operation of the RTC, causing it to reset at every power-up.. When the battery needs replacing, a log message will appear in the product’s server report. For more information about the server report, see the product’s setup pages or contact Dahua support

WAIRNING

• Risk of explosion if the battery is incorrectly replaced
• Replace only with an identical battery or a battery which is recommended by Dahua.
• Dispose of used batteries according to local regulations or the battery manufacturer’s instructions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>