new one N4001 Z-Wave Mini Smart Plug User Manual
- June 6, 2024
- new one
Table of Contents
Z-Wave Mini Smart Plug
N4001
Specification：
Power: 125VAC, 60Hz
Loading: 15A Max Resistive
Frequency: 908.42MHz
Temperature Range: 32° F ~104° F
Indoor use in a dry location
Features:
- Z-Wave on/off control.
- Z-Wave controlled AC outlet for standard incandescent lighting, CFL/LEDs, fans or small appliances(1800W Resistive Max).
- Grounded 3-wire power connection for safety.
- Remembers and restores on/off status after power failure.
- Built-in Z-Wave Plus signal repeater to extend network range.
- S2 security and 500 Z-Wave chip for reliable wireless communication.
- Work with all certificated Z-Wave controllers.
Z-WAVE INTEROPERABILITY
This product can be included and operated in any Z-Wave network with other
Z-Wave certified devices from other manufacturers and/or other applications.
All non-battery-operated nodes within the network will act as repeaters
regardless of vendor to increase the reliability of the network. This Device
supports Lifeline (association group 1) supporting 1 node for lifeline
communication.
Group 1 must be assigned the Node ID of the primary controller where
unsolicited notifications will be sent. The Z-Wave controller should set this
association automatically after inclusion. Lifeline association only supports
the “Device Reset Locally” function.
Parameter Settings
LED Indicator
This parameter can access you to choose the led indicator to be on when the
switch(light) is on/off, or LED indicator remains on/off all times. (LED flashes
2 times when the configuration parameter changes.)
Operation: quickly press 6x: change parameter
–Parameter =1, size =1 byte,
value=00( default) LED is On when the switch(light) On and LED is Off when the
switch(light) Off.
value=01 LED is On when the switch(light) Off and LED is Off when the switch
(light) On.
value=02 LED is disabled
Auto Turn-Off Timer
This parameter can access you to set a timer to make the switch turn off
automatically after the switch is turned on. The number entered as a value
corresponds to a number of minutes. (LED flashes 2 times when the
configuration parameter changes.)
Operation: Set up on the hub.
–Parameter =2, size=4 byte, value range: 0 – 65535 (Min), Value=0(default)
turn off the outlet
Auto Turn-On Timer
This parameter can access you to set a timer to make the switch turn on
automatically after the switch turned off. The number entered as a value
corresponds to a number of minutes. (LED flashes 2 times when the
configuration parameter changes.)
Operation: Set up on the hub.
–Parameter =4, size=4 byte, value range: 0 – 65535 (Min),
Value=0(default) turn on the outlet
Restores state after power failure
This parameter can access you to set the switch to be on/off after power
failure. (LED flashes 2 times when the configuration parameter changed.)
Operation: Quickly press the button 10 times (Please note: the switching of
each value is in order, a quick press on the button 10 times will switch once.
eg: Switching from value 0 to value 2 needs 2 switchings. )
–Parameter=6，Size=1
Value=0———–The switch is off regardless of the state prior to power failure.
Value=1———–The switch is on regardless of the state prior to power failure.
Value=2(default)———–This switch will be return to state prior to the power
failure after power is restored.
Generic Device Class:
0x10 – GENERIC_TYPE GENERIC_TYPE_SWITCH_BINARY
Specific Device Class:
0x01 – SPECIFIC_TYPE SPECIFIC_TYPE_POWER_SWITCH_BINARY
Command Classes:
0x5E – COMMAND_CLASS_ZWAVEPLUS_INFO_V2,
0x25 – COMMAND_CLASS_SWITCH_BINARY,
0x85 – COMMAND_CLASS_ASSOCIATION,
0x8E – COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2,
0x59 – COMMAND_CLASS_ASSOCIATION_GRP_INFO,
0x55 – COMMAND_CLASS_TRANSPORT_SERVICE_V2,
0x86 – COMMAND_CLASS_VERSION,
0x72 – COMMAND_CLASS_MANUFACTURER_SPECIFIC,
0x5A – COMMAND_CLASS_DEVICE_RESET_LOCALLY,
0x73 – COMMAND_CLASS_POWERLEVEL,
0x70 – COMMAND_CLASS_CONFIGURATION,
0x9F – COMMAND_CLASS_SECURITY_2,
0x6C – COMMAND_CLASS_SUPERVISION
0x7A – COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
Notes:
-
Plug the device you want to control into the Z-Wave Smart plug-controlled outlet.
NOTE : Plug directly into the outlet, do not use with extension cords.
-
Your device may need to be within 100 feet of the controller to be included. If so, include the device in the network within 10 feet of the controller and relocate it to the desired position in your home. Be sure to refresh the network if the device is included in this manner.
Z-Wave Network Configuration
Adding Device To Z-Wave Network
- Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.
- Once the controller is ready to add your device, press the Manual/ Program button on the smart plug 3 times quickly. The blue LED will blink quickly. Auto-add mode: LED will blink within 30 seconds after first plugging in. Now, you have complete control to turn your fixture ON/OFF according to groups, schedules, and interactive automation programmed by your controller. If your Z-Wave certified controller features remote access, you can control your fixture from your mobile devices.
Again: If you have issues with pairing/including, please move the device
as close as possible to the hub and try again–you can move to your final
location when
completed.
Note : If the manual button doesn’t light up after being pressed 3 times,
please reset the device: click the button 2 times quickly then hold for at
least 10 seconds. This operation could be done when manual control is
functional–a single press can turn on/off the lamp.
To Remove The Device
- Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.
- Once the controller is ready to remove your device, press the manual/program button on the smart plug 3 times quickly.
To Return The Device To Factory Defaults:
Manual: Click the button 2 times quickly then hold for at least 10
seconds.
Host reset : Remove it from the hub the device will factory reset.
Association
(LED flashes 2 times when the configuration parameter changes.)Support 2
groups, each group max support 5 devices Group 1 lifeline Group 2 Left outlet
send basic set
Please contact us if you have any questions:
www.newonetree.com
ask@newone-tech.com
Warranty
Our Products warrants this product to be free from manufacturing defects for a
period of one year from the original date of consumer purchase. This warranty
is limited to the
repair or replacement of this product only and does not extend to
consequential or incidental damage to other products that may be used with
this product. This warranty
is in lieu of all other warranties, expressed or implied. Some states do not
allow limitations on how long an implied warranty lasts or permit the
exclusion or limitation
of incidental or consequential damage, so the above limitations may not apply
to you. This warranty gives you specific rights, and you may also have other
rights which vary
from state to state.
FCC / IC
This device complies with part 15 of the FCC and Industry Canada license-
exempt RSS standard(s). Operation is subjected to the following two
conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC NOTE:
The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Important note:
To comply with the FCC RF exposure compliance requirements, no change to the
antenna or the device is permitted. Any change to the antenna or the device
could result in the device exceeding the RF exposure requirements and void the
user’s authority to operate the device.
CAUTION – PLEASE READ!
This device is intended for installation in accordance with the National
Electric Code and local regulations in The United States, or the Canadian
Electrical Code and local regulations in Canada. If you are unsure or
uncomfortable about performing this installation consult a qualified
electrician.
WARNING
RISK OF FIRE
RISK OF ELECTRICAL SHOCK
RISK OF BURNS
TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS PRODUCT HAS A GROUNDING-TYPE PLUG
THAT HAS A THIRD
(GROUNDING) PIN. THIS PLUG WILL ONLY FIT INTO A GROUNDING-TYPE POWER OUTLET.
IF THE PLUG DOES NOT
FIT INTO THE OUTLET, CONTACT A QUALIFIED ELECTRICIAN TO INSTALL THE PROPER
OUTLET. DO NOT CHANGE THE PLUGIN ANY WAY.
CONTROLLING APPLIANCES:
CAUTION: TO REDUCE THE RISK OF
OVERHEATING AND POSSIBLE DAMAGE TO
OTHER EQUIPMENT
- DO NOT EXCEED RATINGS
- DO NOT USE TO CONTROL ANY DEVICE
WHERE UNINTENDED OPERATION COULD CAUSE UNSAFE CONDITIONS (HEAT LAMP, SUN LAMP, ETC.)
MEDICAL EQUIPMENT
Please DO NOT use this switch to control Medical or Life Support equipment.
Z-Wave devices should never be used to control the On/Off status of Medical
and/or Life Support equipment.
CONTROLLING APPLIANCES
Please exercise EXTREME CAUTION when using Z-Wave devices to control
appliances. The reason being is because the appliance you want to control may
be in a separate room and if unintentional behavior occurs (such as a device
turning on or off – either intentionally via schedules, or unintentionally via
network error) this event may lead to a hazardous condition. For these
reasons, please note the following suggestions:
- Do not include Z-Wave devices in Groups or Scenes if they control appliances.
- Do not use Z-Wave devices to control electric heaters or any other appliances which may present a hazardous
condition due to unattended, unintentional, or automatic power control.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>