BRAUN MQ9137XI 9 Hand Blender Instruction Manual

: June 6, 2024
: Braun

Table of Contents

BRAUN MQ9137XI 9 Hand Blender
IMPORTANT SAFET Y INSTRUCTIONS
LITTLE MARK IV / LITTLE MARK IV 300 FRONT PANEL
TECHNICAL DETAILS
COMBOS: TECHNICAL DETAILS
TROUBLESHOOTING TIPS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BRAUN MQ9137XI 9 Hand Blender

IMPORTANT SAFET Y INSTRUCTIONS

Read these instructions;
Keep these instructions;
Heed all warnings;
Follow all instructions;
Do not use this apparatus near water;
Clean only with dry cloth;
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that produce heat;
Do not defeat the safety purpose of the polarized or ground-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet;
Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and thepoint where they exit from the apparatus;
Only use attachments/accessories specied by the manufacturer;
Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from the tip-over (andFig 21 DU Tipping Cart Symbol).
Unplug this apparatus during lightning storms or when unused for long periods of time;
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in anyway, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,the apparatus
“Warning: to reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture; and objects
filled with liquids, such as vases, should not be placed on this apparatus”;
To completely disconnect this apparatus from the AC mains, disconnect the power supply cord plug from the AC receptacle;
The mains plug of the power supply cord shall reamin readily accessible.
In case of voltage selector make sure the switch on the rear panel is on the correct voltage before connecting it to the AC power, and the fuse is the right value for that voltage (This selector is not available on the 100V version).
Please change the voltage/fuse values label located near the voltage selector matching the voltage/fuse values when you need to change the voltage of the apparatus.
“WARNING: this apparatus must be securely attached to the door or wall in accordance with installation instruction. Tipping, shaking, or rocking the machine may cause injury or death.”
TAKE CARE WHEN LIFTING

LITTLE MARK IV / LITTLE MARK IV 300 FRONT PANEL

FRONT PANEL

FRONT PANEL

UNBALANCED 1/4” JACK INPUT
MUTE SWITCH
SOLID STATE GAIN
CLIP LED
LOW EQUALIZATION CONTROL KNOB
MID LOW EQUALIZATION CONTROL KNOB
MID HIGH EQUALIZATION CONTROL KNOB
HIGH EQUALIZATION CONTROL KNOB
OLD SCHOOL FILTER
LINE OUT LEVEL KNOB
MASTER VOLUME LEVEL KNOB
FOOTSWITCH INPUT
3-WAY ROTARY SWITCH (FLAT/SCOOPED-MID/FSW)
SCOOPED-MID EQ LED

LITTLE MARK IV / LITTLE MARK IV 300 U/ LITTLE MARK IV NINJA / LITTLE MARK IV COMBO REAR PANELMAIN ON/OFF SWITCH

AC POWER SOCKET
SPEAKER OUT SPEAKON / 1/4” COMBO JACK (LITTLE MARK IV NINJA: SPEAKER OUT SPEAKON)
SPEAKER OUT 1/4” JACK (NOT PRESENT ON LITTLE MARK IV NINJA)
TUNER OUT 1/4” JACK
RETURN EFFECT 1/4” JACK
SEND EFFECT 1/4” JACK
PRE/POST EQUALIZATION CONTROL SWITCH
GROUND LIFT CONTROL SWITCH
LINE OUT XLR

LITTLE MARK IV / LITTLE MARK IV 300 / LITTLE MARK IV NINJA / LITTLE MARK IV COMBO

TECHNICAL DETAILS

INPUTS
INPUT impedance: 1 Mohm, max. voltage: 9 Vpp RETURN impedance: 22 Kohm, max. voltage: 10 Vpp

CONTROLS
GAIN –46 dB to +23 dB range LINE OUT level control on front panel PRE/POST EQ (for line out) switch on rear panel GROUND LIFT switch on rear panel MUTE SWITCH MASTER VOLUME

EQUALIZATION

LOW center frequency 68 Hz; level: ±16 dB MID LOW center frequency 360 Hz; level: ±16 dB MID HIGH center frequency 800 Hz; level: ±16 dB mHIGH center frequency 10 kHz; level: ±16 dB mOLD SCHOOL max cut range: 250 Hz – 20 kHz 3 WAY SWITCH flat/scooped-mid/FSW

OUTPUTS

SEND EFFECTS unbalanced, max. voltage 20 Vpp TUNER OUT unbalanced, max. voltage 2 Vpp LINE OUT balanced XLR, max. voltage 20 Vpp SPEAKER OUT speakon/1/4” combo, 1/4” Little Mark IV Ninja : only speakon

OTHERS

HEIGHT 2 rack units (3.27 in. / 83 mmWIDTH 10.87 in. / 27.6 cm (19 in. / 48.3 cm with rack ears) DEPTH 9.84 in. / 25 cm WEIGHT 4.85 lbs / 2.2 kg (LITTLE MARK IV 300) 5.40 lbs / 2.45 kg (LITTLE MARK IV) 6.61 lbs / 3 kg (LITTLE MARK IV NINJA)
LIMITER
FOOTSWITCH (OPTIONAL) FLAT/SCOOPED-MID/FSW

OUTPUT POWER

300W RMS @ 4 ohm, 150W RMS @ 8 ohm (LITTLE MARK IV 300)
500W RMS @ 8 ohm, 300W RMS @ 4 ohm (LITTLE MARK IV/LITTLE MARK IV COMBO)
1000W RMS @ 4 ohm, 600W RMS @ 8 ohm (LITTLE MARK IV NINJA)

POWER REQUIREMENT

LITTLE MARK IV, LITTLE MARK IV 300, LITTLE MARK IV COMBO,LITTLE MARK IV NINJA 100V; 120V; 230V; 240V 50/60Hz
(Voltage is factory preset according to region of sale).
Markbass amps/combos are manufactured to be sold and used in the country of purchase, and are factory preset to that country’s voltage.
Due to homologation issues, the voltage may not be changed.
FUSE
LITTLE MARK IV, LITTLE MARK IV COMBO:

EUROPE 4 A 250V T 5x20UK 4 A 250V T 5×20 USA / CANADA 8 A 250V T 5x20JAPAN 10 A 250VT 5×20

LITTLE MARK IV NINJA
EUROPE 8 A 250V T 5x20AUSTRALIA/UK 8 A 250V T 5x20USA/CANADA 10 A 250V T 5x20JAPAN 12 A 250VT 5×20
MARK IVLITTLE 300

EUROPE 3.15A 250V T 5×20 AUSTRALIA/UK 3.15A 250V T 5x20USA/CANADA 6.3A 250V T 5×20
JAPAN 6.3A 250V T 5×20

COMBOS: TECHNICAL DETAILS

TECHNICAL DETAILS

TROUBLESHOOTING TIPS

THERMAL PROTECTION

SYMPTOM The amp gets hot and shuts down.
PROBABLE CAUSE The amp has overheated, either as a result of inadequate ventilation or a damaged cooling system fan. When the amplifier cools down to a safe level, the amp will automatically restart.
SUGGESTIONS Please verify that the fan is working properly, and that the cooling system ports are not obstructed.
CURRENT PROTECTION
SYMPTOM The amp turns on, but there is no signal coming from the speaker/s.
PROBABLE CAUSE Low impedance load (minimum impedance for Markbass amps is 4 ohms), or a bad speaker cable.
SUGGESTIONS Please verify the impedance of the speaker/s connected to the amp. Note that two 4 ohm cabinets, or an 8 ohm and a 4 ohm cabinet, will result in an impedance below 4 ohms. Please check the speaker cable/s. After checking these two things, please turn the amp off and turn it on again. If the troubleshooting steps outlined above do not solve your problem, please contact your Markbass distributor/dealer for service information. For more TROUBLESHOOTING TIPS, please check the FAQ section on the SUPPORT page of our website at www.markbass.it