QYT KT-9900 25W Waterproof Mini Car Two Way Radio User Manual

June 6, 2024
QYT

KT-9900 25W Waterproof Mini Car Two Way Radio
Hand microphone display platform

User ManualQYT KT 9900 25W Waterproof Mini Car Two Way
Radio

Catalog

Matters need attention
Unpacking and inspection device
Panel description
Same frequency and different frequency channel storage
Co-channel storage
Inter-frequency channel storage (connection relay station operation)
Different frequencies plus CTCSS/DCS channel storage (connected to relay station operation)
Operation menu function setting
Menu function setting operation (which can be operated by keyboard)
Manual channel storage and deletion operation Store radio channel
Switch keyboard lock. send transit signaling
The setting of PTT ID| Optional signaling settings
DTMF signaling settings
DTMF signaling
Patrol function
Monitoring work
Telehalo function
Remote death function
Boot function
Alarm function ….
CALL key to send DTMF settings
CALL key sends dual-tone and dual-tone signal to set 5TONE signaling setting
Hand microphone description ..
Function menu table the key technical indexes
---|---

matters need attention

Please observe the following precautions to prevent fire, personal injury, and damage to the interphone.

  1. Do not use this machine while driving, it is too dangerous to do so.

  2. This walkie-talkie is designed to use a 13.8V DC power supply and does not use a 24V power supply for power supply.
    Do not place the machine in a dusty, wet, or splashed place, and do not place it on an unstable surface.

  3. If the reception is interfered with by the outside, keep the unit away from interfering equipment (such as TV set, generator, etc.).

  4. Do not expose this unit to direct sunlight for a long time or place it near the heating device.

  5. If the machine emits smoke or a strange smell, the power should be cut off immediately. After confirming that the machine is safe, send it to the nearest maintenance service station for inspection.

  6. Do not transmit with high power output for a long time, which may cause the intercom to overheat.

Unpacking and inspection device
Welcome to the radio. Before use, I suggest you:

  1. Please check the packing box of this product for signs of damage;
  2. Please carefully open the packing box and confirm whether there are items listed in the table below;
  3. If you find that this product and its accessories are lost or damaged during handling, please contact the dealer immediately.

What’s in the Box

QYT KT 9900 25W Waterproof Mini Car Two Way Radio - figure
1

Overview of the Front Panel

QYT KT 9900 25W Waterproof Mini Car Two Way Radio - figure
3QYT KT 9900 25W Waterproof Mini
Car Two Way Radio - figure 4

11: power cord 12: Antenna interface

Same frequency and different frequency channel storage Co-channel storage

  1. press the required frequency with the keyboard, such as 145.000, press the [Menu] key to display the menu to item, press the [MENU] key to display: 001 flashes (select the number of channels), press the [MENU] key to display CH-001 once, and press the [EXIT] key to save and complete the exit.

  2. Press the required frequency with the keyboard: for example, 146.000, press the [MENU] key to display 47 items in the menu, press the [MENU] key to display 002 flashings (select the number of channels), press the [MENU] key once to display CH-002 and press the [EXIT] key to save and complete the exit.

  3. display channel in section a: in item 29 of the menu, press the “menu” key to display the dishes Monotonic to item 29, showing Press the [MENU] keyThe FREQ flashes and is selected with the knob. CH shows the channel, FREQ shows the frequency+channel number, and press the [MENu] key to confirm.

  4. section b display channel: in item 30 of the menu, press the [Menu] key to display the dishes Monotonic to 30 items, display Press the [MENU] key free flashes, use the knob to select.
    CH shows the channel, FREQ shows the frequency+channel number, and press the [MENU] key to confirm.

  5. Exit the menu, press PTT, and use the [EXIT/AB] key to switch.

Inter-frequency channel storage (connection relay station operation)

  1. press the required receiving frequency, such as 164.500, press the [MENU] key to display menu to 47 items, and display MEM-CH/001, then press the [MENU] key 001 to flash, then press the [MENU] key to display CH-001 once, and after receiving and storing, press the [EXIT] key.
  2. Press the required transmission frequency such as 158.800 with the keyboard, press the [MENU] key to adjust the display menu to 47 items, display MEMCH-O01, press the [MENU] key, CH-001 flashes, press the [Menu] key again, and the different frequency storage is completed, and press the [EXIT] key.

Different frequencies plus CTCSS/DCS channel storage (connected to relay station operation)

(Take receiving 465.525 sub-audio, 67.0 rounds, and 455.525 sub-audio DO23N as an example)

  1. press [[MENU key to display the menu, adjust to 11 items to display R-CTCS/OFF, press [MENu] key to display OFF flashing, use knob to select and receive sub-audio data (67.0), and press [menu] key to confirm.
  2. Use knob to select 12 menus T-DCS/OFF, then press [MENU] key to display OFF flashing, and use knob to select and transmit digital sub-audio data (DO23N), press the  [MENU] key to confirm that [EXIT] is pressed.
  3. Adjust the receiving frequency (press the required receiving frequency of 465.525 with the keyboard), press the [MENU] key to adjust to 47 menus, display MEM-CH/001,  then press the [MENu] key 001 to flash, press the [MENu] key to confirm, display CH001, receive and store, and press [EXIT] to exit.
  4. Press the required radio frequency point with the keyboard, press [MENU] to adjust to 47 items to display MEM-CH001, then press [MENU] to display CHO01 flashing,  press [MENU] to confirm, and press [EXIT] to exit the transmission and storage.

Menu function setting operation (which can be operated by keyboard)

[MENU ]+[0 Key]: TDR turns on and off the dual-fre­quency standby setting. ON is on, which can realize the simultaneous standby waiting of the upper and lower group frequencies on the screen. OFF is off, only waiting for the frequency indicated by the arrow on the screen. After adjustment, press the [MENU] key to store the parameters. 1.

  1. [MENU]+[1 Key]: STEP sets the step value of frequency in frequency mode. It can be set as: 2.5khz, 5khz, 6.25khz, 10khz, 12.5khz and 25khz. After adjustment, press the [MENU] key to store the parameters.

  2. [MENU]+[2 key]: setting the squelch level of SQL receiver, which is divided into 10 levels to set the squelch depth according to the use environment. 0 is mute on; 1-9 is mute depth increasing; after adjustment, press [F Key] to store parameters.

  3. [MENU]+[3 Key]: TXP transmits power setting. HIGH is the high power output and LOW is the low power output. After adjustment, press the [MENU] key to store the parameters.

  4. [MENU ]+[4 Key]: SCR voice encryption scrambling setting. ONTo turn it on, call voice encryption can be realized. OFF is off. After adjustment, press the [MENU] key to store the parameters. (This function is optional)

  5. [MENU]+[5 Key]: TOT emission time limit setting. Set the transmission time of each intercom. The value ranges from 15 to 600 seconds, with steps of 15. After adjustment, press the [MENU] key to store the parameters.

  6. VOL: Volume 0, 1,2,3, 63 Adjust the output volume of the car platform. The higher the number, the higher the volume.

  7. [MENU]+[7 Key]: WN width and narrowband setting. WIDE is wideband and NARR is a narrow band. After adjustment, press the “MENU]” key to store the parameters.

  8. [MENU]+ [8 key]: automatic backlight time setting of ABR screen. OFF sets the screen to be always on, and the value of 1-50 seconds can adjust the backlight time of the screen. After adjustment, press the [Menu] key to store the parameters.

  9. [ MENU ]+ [9 Key]: BEEP tone switch. OFF is off and ON is on. After adjustment, press the [MENU] key to store the parameters.

  10. [MENU]+[1 Key]+[0 Key]: R-DCS receives digital sub-audio setup. OFF means off, DO23N-D754N is a forward standard digital sub-audio sequence, and DO23l- D754I is a reverse standard digital sub-audio sequence. After adjustment, press the [Menu] key to store the parameters.

  11. [MENU]+[1 Key]+[1 Key]: R-CTCS receive analog sub-soundsFrequency setting. OFF means off, 67.0HZ-254.1HZ simulates the standard sequence of mute, and at the same time, you can directly type the standard or non-standard analog mute through the keyboard. After adjustment, press the [MENU] key to store the parameters.

  12. [MENU]+[1 Key]+[2 Key]: T-DCS transmits digital sub-audio Setup. OFF means off, DO23N-D754N is a forward standard digital sub-audio sequence, and DO23I- D754I is a reverse standard digital sub-audio sequence. After adjustment, press the [MENU] key to store the parameters.

  13. [ MENU]+[1 Key]+[3 Key]: T-CTCS transmit analog sub-sounds Frequency setting. OFF means off, 67.0HZ-254.1HZ simulates the standard sequence of mute, and at the same time, you can directly type the standard or non-standard analog mute through the keyboard. After adjustment, press the [MENU] key to store the parameters.

  14. D-SUB: sub-audio display switch OFF turns off the sub-audio display. at this time, ONly sub-audio symbols are displayed, but the specific values of sub-audio are not displayed. on turns on the sub-audio display to display the sub-audio values currently sent and received.

  15. [MENU]+[1 key]+[4 key]: DTMF ST DTMF sidetone is onClose the setting. OFF is off, when sending DTMF code, this machine does not send out the sound of this code, and KEY only sends out the sound of this code when pressing the key to sending DTMF code. ANI only sends out the sound of the code when it sends the code automatically. BOTH key code sending and automatic code sending are sent locally

  16. [MENU ]+[1 Key]+[6 Key]: SC-ADD scan and add settings Set. When the storage channel is turned OFF, the stored channel is not added to the scan list. When storing channels ON, the stored channels should be added to the scan list. After adjustment, press the [MENU] key to store the parameters.

  17. [MENU]+[1 Key]+[7 Key]: PRI-SC priority scanning setting. OFF turns off priority scanning, and ON turns on priority scanning. After adjustment, press the [MENU] key to store the parameters.

  18. [MENU ]+[1 Key]+[9 Key]: SC-REV scanning recovery mode Setup. TO scan in time mode. After receiving the carrier signal, it will stay for a period of time and continue scanning. CO scans in carrier mode and stops scanning when receiving carrier signal. SE scans in search mode and receives a carrier signal

  19. [ MENU]+[2 Key]+[0 Key]: OPTSIG signaling mode setting. OFF means no signaling, DTMF means dual audio signaling, 2TONE means two-tone signaling, and  5TONE means five-tone signaling. After adjustment, press the [MENU] key to store the parameters. Stop scanning when the signal and signaling match with this machine at the same time. After adjustment, press the [MENU] key to store the parameters.

  20. [MENU]+[2 Key]+[1 Key]: SPMUTE speaker turn-on mode setting. QT turns on the speaker for matching the received sub-audio with the sub-audio set by this machine. If no sub-audio is set, the speaker will be turned on after receiving the carrier. AND turns on the hORn when the received sub-audio and optional signaling match with the sub-audio and optional signaling set by the local machine or turns on the horn when the received sub-audio and optional signaling match with the sub-audio and optional signaling set by the local machine or turns on the horn after receiving the carrier if no sub-audio is set. After adjustment, press the [MENU] key to store the parameters.

  21. [MENU]+[2 key]+[1 key]: PTT-id PTT-id transmission setting. OFF means no ID code is sent during transmission, BOT means ID code is sent at the beginning of transmission, EOT means ID code is sent at the end of transmission, and BOTH means ID code is sent at the beginning and end of transmission (ID code is the signaling information code in dial-up memory preset by PC software, which can be selected through item 24 of the menu). After adjustment, press the [Menu] key to store the parameters.

  22. [menu]+[2 key]+[2 key]: PTT-lt PTT-id transmission delay setting. 0-30 delay time before sending ID code (in seconds). After adjustment, press the [MENU] key to store the parameters.

  23. [MENU]+[2 Key]+[4 Key]: S-INFO signaling information and automatic Dial-up memory. 1-15 groups of signaling encoding and decoding memories. You can only write with PC software. After adjustment, press the [MENU] key to store the parameters.

  24. [MENU ]+[2 Key]+[5 Key]: EMC-TP alarm mode setting Set. ALARM is the alarm tone sent by this machine, ANI is the alarm code and local identity code sent when alarming, and BOTH alarm tones and local identity codes are sent by this machine when alarming. After adjustment, press the [Menu] key to store the parameters.

  25. [ MENU ]+[2 Key]+[6 Key]: EMC-CH alarm channel setting Set. 000-199 CHannel, the designated alarm channel when alarming, and ch is displayed as an effective channel in front of this channel. After adjustment, press the [MENU] key to store the parameters.

  26. [MENu]+[2Key]+[6key] sIG-BP: signaling includes Effective tips. OFF turns off the optional signaling without reminding when it is valid.

  27. [ MENU]+[2 Key]+[ 7Key]: CHNAME channel name Series. In channel mode, edit the channel name of the current channel. After adjustment, press the [MENU] key to store the parameters.

  28. [menu]+[2 key]+[8 key]: ca-media channel display settings. In CHannel mode, FREQ is displayed as frequency, ch is displayed as channel number, and NAME is displayed as channel name (the specific name is set in writing frequency software). After adjustment, press the [MENU] key to store the parameters.

  29. [menu]+[2 key]+[9 key]: CB-MDF b channel display settings. In CHannel mode, FREQ is displayed as frequency, ch is displayed as channel number, and NAME is displayed as channel name (the specific name is set in writing frequency software). After adjustment, press the [MENU] key to store the parameters.

  30. CC-MDF: C- channel shows that area c is in channel mode, Channels are displayed in frequency. Area C is in channel mode, the channel is displayed by channel number. C  zone is in the letter In channel mode, channels are displayed by channel name (the specific name is set in the writing frequency software)

  31. LANGUAGE : menu language ENG menu is displayed in EnglishThe menu is displayed in Chinese.

  32. DMR_TX: multi-guard transmission TRACK tracking received The frequency point of transmission. The FIXED main frequency is always transmitted at the main frequency.

  33. VOX: voice control transmission is OFF, 1, 2, 3, … 10 OFF voice control transmission is off, 1,2,3, … 10 is voice control start the sensitivity level. The larger the value, the
    more generous the sound Can start.

  34. VOX-T: Voice control delay 0,1,2,3,… 20 OFF Launch off, 1, 2, 3, … 10 is voice-activated and sensitive Degree level, the greater the value, the more generous the sound can be started.

  35. AUTOLK: keyboard auto-lock OFF turns off keyboard auto-lock.ON turns on the keyboard automatic locking function.

  36. ST-FC: Status character display above the character color of status bar Color settings.

  37. MF-FC: Color of dominant characters Display color of dominant characters Setup.

  38. SFA-FC: A- character color a channel display area character color Color settings.

  39. SFB-FC: B- character color b channel display area character Color settings.

  40. Sfc-fc: c-character color c channel display area character color Color settings.

  41. SUB-FC: mute character color sub-audio display character color

  42. FM-FC: BATT color battery/radio frequency display character Color.

  43. SIG-FC: the display color of the status bar at the bottom of the signal bar character color.

  44. MUFC: menu character color menu character when setting menu Display color.

  45. TX-FC: transmission-character color is displayed when the currently active channel is transmitted Show color.

  46. RX-FC: receive-the currently active channel of character color is received Display color when carrier wave is used.

  47. MEM-CH: channel storage 000,…,199 storage letter Channel, used to indicate the channel number to be stored, if Show CH- in front of the number, indicating that Channel parameters are originally stored in the channel.

  48. DEL-CH: channel deletion 000,…,199 deletion designation Channel parameters of the channel, if there is no CH- table before This channel has no parameters, and the  operation is invalid

  49. SFT-D: frequency difference direction setting. OFF off, at frequency In mode, there is no frequency difference between transmitting frequency and receiving frequency.
    +plus In frequency mode, the transmitting frequency is equal to the receiving frequency plus Frequency difference frequency. -frequency reduction in frequency mode, transmission frequency Is equal to the receiving frequency MINUS the frequency difference frequency.

  50. OFFSET: frequency difference frequency setting. 000.000 in frequency mode Type, the difference between the transmitting and receiving frequency (whether to poor  frequency Poor direction control)

  51. ANI: ID code setting XXXXX is used to observe the setting of this machine Identity code (this identity code can only be written by writing software)

  52. ANI-L ID code length 3,4,5 Effective length of local ID code

  53. REP-S: transit signaling settings. 1000,1450,1750, 2100, when transmitting, the single frequency emitted when the CALL key is pressed Tone frequency, used to activate relay station.

  54. TMR-MR: OFF, OFF 1, 2, 3, …50 Main frequency return delay time during multi-frequency waiting

  55. STE: Direct Frequency Tail Elimination OFF Close Close Call Tail EliminatiON function on turn on turn on the call ending elimination function

  56. RP-STE: relay ending elimination, OFF, 1, 2, 3, … 10 eliminates the tail sound generated when relaying

  57. RPT-DL: relay tail delay, OFF, 1, 2, 3, … 10 detect the tail sound of the relay to confirm that the relay is effective.

  58. DTMF-G: DTMF gain 0, 1,2,3, … 60 Set DTMF gain, the larger the value, the other party receives this machine The stronger the DTMF signal sent out,

  59. Reset: the vfo menu is initialized, and ALL restores the factory settings Menu and channel initialization

Manual channel storage and delete operation channel storage:

  1. Enter the frequency to be used directly with the keyboard in frequency mode. For example, the frequency of 435.125MHZ can be directly input into 4, 3, 5, 1, 2, and 5.
  2. Set the receiving sub-audio frequency to be used (menu items 10 and 11) and the transmitting sub-audio frequency to be used (menu items 12 and 13). For example, when receiving sub-audio at 67.0HZ and transmitting sub-audio at 67.0HZ, you can press [MENU] +[1] +[MENU] +[DOWN] to select 67.0HZ+[MENU] +[EXIT/AB] to exit  from saving and receiving sub-audio. To transmit sub-audio, press [F] +[1] +[3] +[MENU] +[DOWN], select 67.0HZ+[MENU] +[EXIT/AB] to exit saving. (If you don’t  need sub-audio, you can all select OFF)
  3. Select menu item 47 for channel storage, and press [MENU] +[4] +[7] +[MENU] +[UP] (DOWN) to select channel number +[MENU] to store channels in turn.

Channel deletion:

Select menu item 37 to delete the channel. Press [MENU] +[4] +[8] +[MENU] +[UP] (DOWN) to select the channel number to be deleted +[MENU] to delete the channel.

Store radio channel

You can store radio programs and corresponding program names through PC frequency writing software. (click on FM channel of frequency writing software to edit). The microphone handle of this machine can send DTMF codes in real- time in the transmitting state. In FM mode, press the [*] key on the microphone keyboard to search radio channels in sequence.

Switch keyboard lock

Press the key [#] of the microphone keyboard for more than 2 seconds during standby time to turn on or off the keyboard lock function.

Send transit signaling

Select the transfer signaling frequency to be sent (this machine provides four transfer signaling frequencies). Press [MENU] +[4] +[2] +[MENU]+[up] (down) to select relay  signaling frequency +F to save. Press the [PTT] key and then press the [CALL] key to send the preset relay signaling.

Setting of PTTID

The PTT-ID sent by this machine is the ID code restored by the writing software. You can write by PC frequency writing software (click PTT-ID option box of optional parameter options of frequency writing software to edit. )

  1. select item 20 in the menu to select the signaling to be used. Press [MENU] +[2] +[0] +[MENU] +[UP] (DOWN) to select the signaling to be used +[MENU] to save.
  2. select item 23, S-INFO signaling code 1,-“,15 in the menu, and send out this group of information codes when necessary (the information codes can only be written by writing frequency software)
  3. Select item 22 in the menu to set PTT transmission delay. Press [MENU] +[2] +[2] +[MENU] +[UP] (DOWN) to select delay time +[MENU] to save.
  4. Press PTT to send the set ID code.

Optional signaling settings DTMF signaling settings

This machine has DTMF coding and decoding function. You can write the signaling information code through PC and frequency software (click the signaling editing DTMF  option of frequency software to set it).

DTMF signaling
After the receiver sets DTMF signaling when receiving DTMF signal and preset body
When the codes are consistent, the receiver will be able to execute the ringing caption and display the information code. In the effective time, you can talk back and forth (the identity code can be written by PC frequency software) To preset).

Patrol function

When the received DTMF signal is consistent with the preset patrol code, the receiver will send it from the Identity code, which can be displayed on the main control screen. This function can choose whether it is controlled by the master ID, and not by the receiving signaling. (the patrol code may be preset by PC writing frequency software).

Monitoring function
When the received DTMF signal is consistent with the preset monitoring code, the receiver will start to transmit the sound that can monitor the surrounding environment in real-time. This function can choose whether it is controlled by the master ID, and not by the receiving signaling. (the monitoring code can be preset by PC writing software).

Telehalo function
When the received DTMF signal is consistent with the preset tele-halo code, the receiver will limit the transmitting function to work only in the receiving state, and the display will prompt. The normal function cannot be restored until the corresponding boot code is received. This function can choose whether it is controlled by the master ID, and not  by the receiving signaling. (Telehalo code can be preset by PC writing frequency software).

Remote death function
When the received DTMF signal is consistent with the preset remote code, the receiver will restrict the use of all functions, and the display will prompt. The normal function cannot be restored until the corresponding boot code is received. This function can choose whether it is controlled by the master ID, and not by the receiving signaling. (the remote code can be preset by PC writing frequency software).

Boot function
When the received DTMF signal is consistent with the preset boot code, the receiver will cancel the function of returning to normal from remote death and halo. This function can choose whether it is controlled by the master ID, and not by the receiving signaling. (the power-on code can be preset by PC writing software).

Alarm function
When the received DTMF signal is consistent with the preset alarm code, the receiver will give an alarm, and the alarm mode and alarm channel can be edited through the optional parameter options of PC frequency writing software. This function is not controlled by master control ID and receiving signaling. (the alarm code can be preset by
PC writing software).

Signaling is controlled by master ID, which means that besides signaling code, master ID must be consistent to perform this function.
Coding format not controlled by master control ID: signaling code+# (separator code)+information code Coding format controlled by master control ID: signaling code+#  (separation code)+master control ID code+# (separation code)+information code

CALL key to send DTMF settings

  1. select DTMF signaling. Press [MENu] +[1] +[9] +[MENu] +[UP] (DOWN) to select DTMF signaling+[menu] to save.
  2. Select signaling information code. Press [MENu] +[2] +[4] +[MENu] +[UP] (DoWN) to select decoded signaling information code group (1-15)+[menu] to save. (DTMF coding can be set by PC frequency writing software)
  3.  Press [CALL] in standby mode to send out the selected

DTMF information code group.
CALL key sends 2 tones and 2 tones signaling settings

  1. Press the [MENU] key (menu function key) to select item 14 OPTSIG and then press the [Menu] key to select 2TONE to start 2TONE signaling.
  2. Press the [MENU] key to select the 24th item S-INFO, and then press the [Menu] key to select the pre-programmed signaling group numbers 1-16. (use of 2TONE can be  set by PC writing software)
  3. When the received 2TONE signal is consistent with the preset 2TONE code, the corresponding function will be executed.
  4. Press the [CALL] key in standby mode to send the selected 2TONE information code group.

TONE signaling setup

This machine has a 5-tone codec function. You can write the signaling information code through PC frequency writing software (click the signaling editing 5TONE option of the frequency writing software to set it). After the receiver sets 5TONE signaling, when the received 5TONE signal is consistent with the preset identity code (the identity code must be 5 digits), the receiver will be able to perform the ringing caption and display the information code. You can talk back and forth within the effective time (the identity code can be preset by PC frequency writing software), and the [CALL] key sends 5TONE

  1. Press the [MENU] key (menu function key) to select the 20th OPTSIG and then press the [F] key to select 5TONE to start 5TONE signaling.
  2. Press the [menu] key to select the 24th item S-INFO, and then press the [F] key to select the pre-programmed signaling group numbers 1-16. [5TONE information code can be set by PC writing frequency software. Each group can send 3 groups of 5TONE codes at a time, and you can choose not to fill them out as needed.
  3. Press the [CALL] key in standby mode to send the selected 5TONE information code group.

Hand microphone description

QYT KT 9900 25W Waterproof Mini Car Two Way Radio - figure
2

Hand microphone description (optional2)

QYT KT 9900 25W Waterproof Mini Car Two Way Radio - figure
5

Short press MOMI and long press power on 1 “: the number 1
Short press CALL and long-press ALARM 2 “: the number 2
MENU function key 3 “: the number 3
UP: frequency step upward 4 “: the number 4
DOWN: frequency step down 5 “: the number 5
6EXIT/VM “,exit AB channel switching, alarm function 6 “: the number 6
  /SCAN: frequency reversal function, scan, the number ”       “ 7 “: the

number 7

/LOCK: keyboard lock function, number “#”| 8″: the number 8

0 “:the number 0| 9″: the number 9

0| TMR| MuInfrequency waiting| ON
OFF| Turn off multi-frequency waiting and start multi-frequency waiting
---|---|---|---|---
1
ri| STEP| Frequency Step Size Setup| 2.5 to 25kHz| 2.5. 5. 6.25. 10. 15, 25 kHz
2| SQL| Squelch Level| 00 > 09| 10 squelch levels, 00 = minimum / normally open
3| TXP| Transmit Power| High
Low| Full Power Reduced Power
4| SCR| Voice Scrambler| ON
OFF| Activate Scrambler Function Deactivate Scrambler Function
5| TOT| Time Out Timer| 15 > 600 secs
OFF
OFF| 15-second steps
Turn off Time out Timer Disable this (unction
6| TOA| Time out timer pre-alert| 12,…10| Radio will alert by LED flashing before transmitting end
7| WN| Bandwidth| V‘rideband
Narrowband| 25.0 kHz
12.5 kHz
8| ABR| LCD Backlight Timer| 1 > 50 secs
OFF| Backlight duration = 1 > 50 Backlight remains ON
9| BEEP| Keypad Voice Prompt| ONE-OFF| Tum ON/GEE keypad voice prompt
---|---|---|---|---
10| R-DCS| Receive – Digital Coded Squelch| D023N > 07541
OFF| Squelch opens when proper DOS code is detected
No DCS code marked
11| T-OCS| Transmit digital mute| OFF D023N D754I| No mute
The standard sequence of digital mute No mow
12| D-SUB| Subtone &play sate`| OFF
OFF ON| Tan off sub-audio
Turn a sub-audio
13| CC-110F| C- channel display| FRED
CH
NAME| In the channel made of zone c. Channels are displayed .1 frequency In the channel mode of zone c. Channel nimbus are (Unlined in frequency
| | | OFF| No tones are heard through the speaker when transmitted
14| DUMPSTER| DTMF Skle Tone| KEY
ANI| Only manually keyed DTMF codes are heard Only automalkalty keyed DIME codes are heard
15| g| Busy Channel Lockout| BOTH
ON
OFF| All DTMF codes are heard
Prevents transmit if the active signal on the channel No lockout
16| SC-ADD| Add Scan Channel| ON Add channel to scan list OFF Remove channel from scan list
---|---|---|---
17| LANGUAGE| Menu language| ENG-The menu is displayed in English Chinese The menu is displayed in Chinese
18| DMR TX| Multi-guard emission| TRACK Always track the received frequency point transmission with the main  frequency transmission FIXED
19| SC-REV| Scan Resume Method| CO (Carrier Operation) Scan stops when signal detected. Scan resumes when signal disappears
20| OPTING| Optional Signaling| SE (Search Operation) Scan stops when signal detected. Scanning will not resume.
OFF No optional signaling
DTMF DTMF signaling selected
2TONE 2TONE signaling selected
5TONE STONE signaling selected
| | | OT| Squelch opens for CTCSS/ DCS tones only.
---|---|---|---|---
| SPMUTE| Speaker Mute Settings| AND
OR
OFF| Squelch opens when CTCSSIDCS tone is recognized along with the optional signaling.
Squelch opens when either the CTCSS/DCS tone OR the optional signaling is recognized.
Do not send
21
22| PTT-ID| PTT ID – When to send| BOT
EOT| Send at Beginning of Transmission Send at the End of Transmission
23
24| PTT-LT| PTT ID – Transmit Delay| BOTH
0 > 30| Send at both Beginning and End Set Delay Time
25| EMC-TP| Alarm Mode| ANI
BOTH| Send Alarm code and ID code Both of the above
| EMC-CH VOX| Alarm Channel Acoustic emission| 000 > 199
OFF. 1, 2, 3, — 10| Specified Alarm Channel
The larger the value the louder the sound. OFF voce control transmission is off. 1 2.3
‘0.”‘ ‘ fro” to
c s., :,-, rites 6 et, ,.,,
26
27
28| NAME| Channel Name| Channel Name Edit
FRED| In Channel Mode, edit the Current Name
29| CA-MDF| A Channel Display Mode| CH
NAME| In Channel Mode, display the selected format in display A
30| CB-MDF B Channel Display Mode| FREQ
CH
NAME| In Channel Mode, display the selected format in display B
Voice control starts transmitting from voice
---|---|---|---
31| VOX-T Voice control delay| 0. 1. 2. 3. ••• 20| The signal disappears to stop transmitting Delay time
32| ST-FC Status bar character color| color| Color setting of upper-status character display
33| MF-FC Color of the dominant character| color| Color setting of main frequency character display
34| SFA-FC A- character color| color| Color setting of characters in the channel a display area
35| SFB-FC B- character color| | Color setting of characters in b channel display area
36| MEMCH Memory Channel| 000 > 199| Indicates channel number to be stored. “CH” will appear after the channel is stored.
37| DELCH Delete Channel| 000′ 199
OFF| Indicates channel number to be deleted. ‘CH” will disappear after channel is deleted.
No Offset (simplex)
---|---|---|---
n| SFT-D Frequency Shift Direction| –| Plus frequency shift Minus frequency shift
39| Frequency Shift Offset
OFFSET
Amount| 00.00 > 69.99| Frequency shift in MHz
40| ANI ANI ID Code| Can only be set with software|
41| ANI-L ANI Length| 3, 4, 5| Length of ANI ID code
42| REP-S Repeater Activation Tone| 1000Hz, 1750Hz
1450Hz. ,
2100Hz| The audible tone for repeater activation
43| SFC-FC C- character color| color| C channel display area character color setting
4| SUB-FC Color of dumb characters| color| Sub-audio display character color
45| Squelch Tail Elimination, STE Requires both radios have
function ON.| OFF
ON| Function OFF
Eliminates squelch tail at end of transmission.
---|---|---|---
46| Repeater Squelch Tail RP-STE Elimination. Requires a
repeater using this function.| OFF
1 > 10| Function OFF Delay Time
47| RPT-DL Repeater squelch tail delay| OFF
1 > 10| Function OFF Delay Time
48| RESET Initialize to Factory Defaults| VFO
ALL| Menu Initialization
Menu and Channel Initialization
49| FM-FC BATT color| color| Battery/radio frequency display Character color
50| SI G-FC Signal bar character color| color| Display color of the bottom status bar
51| MENUFC Menu character color| color| Display color of menu characters when setting menu
52| TX-FC Emission-character color| color| The color displayed when the currently active channel is transmitted
53| RX-FC Receive-Character Color| color| Carrier received by current active channel Display color when
53| MEM-CH Channel storage| 000. …. 199| it means that the channel parameter actually eats. ern channel It the core CH. a depleted In front Of Te barber. Does it weed to Indicate that It should rave arch: tonna? no channel
The charnel number CC
DEL-CH| Channel deletion| 000. •••. 199| If i
there is no CH-, it means the channel
No parameters. invalid operation. delete the channel, parameters of the specified channel.
---|---|---|---
REP-S| Transit signaling| 1000| When launching. it will be launched when the CALL
key is pressed Out of the single-frequency tone frequency. used for excitation Live relay station
TMR-MR| Main frequency return delay| OFF. 1, 2, 3, •••SO| Main frequency return delay time during multi-frequency waiting
RPT-DL| Relay tail delay| OFF. 1, 2, 3, -SO| Detect the tail sound of the relay to confirm this time Turn effective
DTMF-G| Dual-tone multifrequency gain| OFF. 1, 2, 3, -60| Set DTMF gain, the larger the value, the other party The stronger the DTMF signal received from this machine.
SIG-BP| Signaling valid prompt| OFF ON| Don’t remind when optional signaling is valid to Remind when optional signaling is valid

The key technical indexes Overall specifications

frequency range| 144-148/420-450MHz (Tx)
136-174/400-480MHz (Rx) and 88.1-108Mhz (FM Radio Rx )
---|---
Number of channels| 200 channels
channel spacing| 25KHz 20KHz 12.5KHz
Phase-locked stepping| 5KHz, 6.25KHz, 10KHz, 12.5KHz, 15KHz, 25KHz,
operating voltage| 13.8V DC ± 15%
Mute mode| CTCSS / DCS / 5Tone / 2Tone I DTMF
frequency stabilization| ± 2.5ppm
Operating temperature of degree| -20-+60t
measure| 98 (W) x35 (H) x118 (D)mm
weight| 408g

Receiving part (ETSI EN 300 086 standard test)

| Bandwidth| narrow band
---|---|---
Sensitivity (12dB SINAD)| C 0.25pV| c 0.35[N
Adjacent channel selectivity| _. 70dB| …– 60dB
intermodulation| .- 65dB| 60dB
False signal response| ..-70dB| …–70dB
audio response| +1–3dB (0.3-3KHz)| +1–3dB (0.3-2.55KHz)
SNR|
.?– 45dB| -40dB
Audio distortion| –..5%
Audio output power| .
.–‘2W ± 10%

Transmitting part (ETSI EN 300 086 standard test)

| Bandwidth| narrow band
---|---|---
output rating| 20W(VHF/UHF)
modulation system| 16K(bF3E| 11 K4)F3E
Adjacent channel power| „- 70dB| …- 60B
SNR| — 40dB| ,- 36dB
Parasitic and harmonic| _?:- 60dB| ….- 60dB
audio response| +1–3dB (0.3-3KHz)| +1–3dB (0.3-2.55KHz)
Audio distortion| C5%

Note: All specifications are subject to change without prior notice or liability.

FCC Compliance Statements:
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

Licensing Information

Using our radio in the USA is subject to the rules & regulations of the FCC. Changes or modifications not expressly approved by our may void the user authority granted by the FCC to operate this radio and should not be made. To comply with FCC requirements, transmitter adjustments should be made only by or under the supervision of a person certified as technically qualified to perform transmitter maintenance and repairs in the private land mobile and fixed services as certified by an organization representative of the user of those services. Replacement of any transmitter component (crystal, semiconductor, etc) not authorized by the FCC equipment authorization for this radio could violate FCC rules.
Note: The use of this radio outside the country where it was intended to be distributed is subject to government regulations and may be prohibited.
Important: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device. Your radio is set up to transmit a regulated signal at an assigned frequency. It is against the law to alter or adjust the settings inside the radio to exceed those limitations. Any adjustments to your radio must be made by qualified technicians.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals