niceboy HIVE BONES 2 Wireless Headphones User Manual
- June 7, 2024
- niceboy
Table of Contents
niceboy HIVE BONES 2 Wireless Headphones
PRODUCT DESCRIPTION
- Microphone
- Multifunction button
- Charging microUSB port
- Volume up / Switching the headphones on or off button
- Volume down button
- LED indicator
WEARING THE HEADPHONES PROPERLY
Put on the headphones according to the picture, since incorrect use can result
in poor quality of playback
CONNECTING TO BLUETOOTH
-
To connect to a Bluetooth device for the first time, press and hold the power key (4); the headphones will turn on (an acoustic prompt will announce this) and automatically enter the pairing mode, while the LED indicator (6) will start flashing red-blue.
-
Now open the Bluetooth settings of your device and select Niceboy HIVE Bones 2“
from the available devices. -
The headphones will now connect to the device. Successful pairing is indicated by an acoustic prompt and an LED indicator (6) will start flashing blue.
In order to reconnect a previously paired device with the headphones, you just have to switch on by pressing the on button (4) for 3 seconds (an acoustic prompt sounds) and the headphones connect to it automatically.
BASIC OPERATION
Press button (4) for 3 seconds to switch the headphones on / off.
To turn the volume up / down, briefly press buttons (5) and (4).
Briefly press the multifunction button (2) to start / stop playback.
Press the button briefly two times to skip to the next song.
Press the button briefly three times to skip to the previous song.
PHONE CALLS
To answer / end an incoming call, briefly press the multifunction button (2).
To reject the incoming call, press and hold the multifunction button (2) for 3
seconds.
VOICE ASSISTANTS
To start voice assistants, press and hold the multifunction key for 3 seconds.
Press and hold again to close the voice assistant mode.
FACTORY SETTINGS
For resolving possible connection problems or other software problems. To
reset the headphones, press and hold the power button (4) and the volume down
button (5) at the same time for 5 seconds.
CHARGING
We recommend that you fully charge the headphones before using it for the
first time to maximize battery life. It takes approximately 2 hours to fully
charge the headphones.
A low battery condition is indicated by an acoustic signal. To charge the
headphones, connect the supplied USB-C cable to the charging port of the
headphones (3) and then connect it to any charging adapter (5V voltage and at
least 1A output current) or to a USB in a PC. The charging progress is
signalled by the red LED indicator (6); when fully charged, the indicator
lights up blue. After connecting the charging cable, the headphones will turn
off and cannot be connected to any device.
PACKAGE CONTENTS
- Niceboy HIVE Bones 2 Headphones
- USB-C charging cable
- Earplugs
- Instruction manual
PARAMETERS
This product complies with all the basic requirements of relevant EU directives.
USER INFORMATION FOR DISPOSING ELECTRICAL AND ELECTRONIC DEVICES (HOME USE)
This
symbol located on a product or in the product’s original documentation means
that the used electrical or electronic products may not be disposed together
with the communal waste. In order to dispose of these products correctly, take
them to a designated collection site, where they will be accepted for free. By
disposing of a product in this way, you are helping to protect precious
natural resources and helping to prevent any potential negative impacts on the
environment and human health, which could be the result of incorrect waste
disposal. You may receive more detailed information from your local authority
or nearest collection site. According to national regulations, fines may also
be given out to anyone who disposes of this type of waste incorrectly. User
information for disposing electrical and electronic devices.
(Business and corporate use)
In order to correctly dispose of electrical and electronic devices for
business and corporate use, refer to the product’s manufacturer or importer.
They will provide you with information regarding all disposal methods and,
according to the date stated on the electrical or electronic device on the
market, they will tell you who is responsible for financing the disposal of
this electrical or electronic device. Information regarding disposal processes
in other countries outside the EU. The symbol displayed above is only valid
for countries within the European Union. For the correct disposal of
electrical and electronic devices, request the relevant information from your
local authorities or the device seller.
Importer to EU: RTB media s.r.o., Pretlucka 16, Prague 10, 100 00, Czech
Republic, ID: 294 16 876
Made in China.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>