AODELAN 928459 Flash Trigger Transmitter User Manual

: June 6, 2024
: AODELAN

Table of Contents

Features:
Channel List for 2.4G system:
Channel List for 3XXMHz system:
FCC Warning
INDUSTRY CANADA STATEMENTS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

User Manual

Features:

For triggering and remote control of Flash
Dual RF system
Dual RF system, One system can receive and transmit, and the working frequency channels between 2404~2480 MHz, the other system only can work on receive. and the working frequency channel is：315MHZ-435MHZ.
Up to 100 m range outside
Up to 50 m range inside
Modulation mode is MSK,
Demodulation mode is MSK(2.4GHz) and ASK and MSK and GFSK(315MHZ-435MHz）,
Common RX and TX interface
250kbps, 1, and 2Mbps air data rate
1.9 to 3.6V supply range
Antenna: PCB antenna(2.4GHz) and Helix antenna(315MHz-435MHz)
Working Temperature: -10℃～+40℃
Working Humidity: 35﹪～95﹪RH

Other channels (MHZ):
2404 2405 2406 2407 2408 2409 2410 2411 2412 2413 2414 2415 2416 2417 2418 2419 2420 2421 2422 2423 2424 2425 2426 2427 2428 2429 2430 2431 2432 2433 2434 2435 2436 2437 2438 2439 2440 2441 2442 2443 2444 2445 2446 2447 2448 2449 2450 2451 2452 2453 2454 2455 2456 2457 2458 2459 2460 2461 2462 2463 2464 2465 2466 2467 2468 2469 2470 2471 2472 2473 2474 2475 2476 2477 2478 2479 2480

Channel List for 3XXMHz system:

315MHz-435MHZ

Radiation Exposure Statement

This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

FCC Warning

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

INDUSTRY CANADA STATEMENTS

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The ISED certification label of a module shall be clearly visible at all times when installed in the host product; otherwise, the host product must be labeled to display the ISED certification number for the module, preceded by the word “contains” or similar wording expressing the same meaning, as follows: contains IC:25192-RF8.
As long as the three conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
Important Note:
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The final end product must be labeled in a visible area with the following” Contains FCC ID: 2AEJW-RF8″ Manual Information to the End-User The OEM integrator has to be aware not to provide information to the end-user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end-user manual shall include all required regulatory information/warning as shown in this manual. Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01
2.2 List of applicable FCC rules CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular transmitter
2.3 Specific operational use conditions This module is a stand-alone modular. If the end product will involve Multiple simultaneously transmitting conditions or different operational conditions for a stand-alone modular transmitter in a host, the host manufacturer has to consult with the module manufacturer for the installation method in the end system.
2.4 Limited module procedures This module is a Limited to single modular without shielding, host manufacturer has to consult with the module manufacturer for the module limiting conditions when integrating the module in the host. module manufacturer should review detailed test data or host designs prior to giving the host manufacturer approval.
2.5 Trace antenna designs Not applicable
2.6 RF exposure considerations This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
2.7 Antennas The module is not designed for multiple antenna applications and should not be used to transmit simultaneously with any other transmitter. The module is only certified to use the integrated PCB antenna.Antenna Description:PCB Antenna antenna,Max
Gain:3.0dBi.
2.8 Label and compliance information The final end product must be labeled in a visible area with the following” Contains FCC ID:2AEJW-RF8″.
2.9 Information on test modes and additional testing requirements Host manufacturer which installs this modular with limited modular approval should perform the test of radiated emission and spurious emission according to t o FCC part 15C:15.247 and 15.209 requirements, only if the test result complies with FCC part 15.247 and 15.209 requirement, then the host can be sold legally.
2.10 Additional testing, Part 15 Subpart B disclaimer Host manufacturer is responsible for compliance of the host system with the module installed with all other applicable requirements for the system such as Part 15B.
Note: The module will later be used on the flash and flashers and the associated remote control equipment（only for Shenzhen Aodelan Technology Co., Ltd.）