nile NWA1000 Wireless Access Point Installation Guide
- June 6, 2024
- nile
Table of Contents
nile NWA1000 Wireless Access Point Installation Guide
Product Specification
Product dimensions
| 245mm x 245mm x 50mm (exclude universal mounting kit)
---|---
Product weights|
1.75kg
Radio frequency
| One Wi-Fi 2.4GHz One Wi-Fi 5GHz One Wi-Fi 2.4/5GHz(scanning) One Bluetooth
2.4GHz
Operation frequency|
2.4GHz 5GHz Bluetooth low energy(V4.1) 2.4G : 2412 ~ 2462MHz 5G: 5180~5240MHz 5500~5700MHz 5260~5320MHz 5745~5825MHz BT : 2402 ~ 2480MHz
Networking interface
| Two 5G mGig Ethernet ports
Antenna Gain|
Wi-Fi 2.4GHz band : 4.6 dBi (Omni) Wi-Fi 5GHz band: 5 dBi (Omni) Dual band Wi- Fi(2.4/5GHz): 4.6/5dBi (Omni) BLE: 4.4dBi (Omni)
Max power consumption
| 35watts
Power source|
DC power: 12V/3.5A power adapter Power over Ethernet(PoE): 802.3bt
Mounting mode
| Ceiling,
Operation temperature|
0 ~ 45 C
Operation humidity
| 5 – 95% Noncondensing
Altitude|
10,000ft (3,048m)
Installation Guide
Installation of ceiling plate + AP on T-bar (9/16” & 15/16”)
-
Align T-bar with ceiling plate
Note: The picture is for reference.
-
Slide ceiling plate/AP together until T-bar under slots of ceiling plate.
Uninstallation of ceiling plate + AP from T-bar (9/16” & 15/16”)
-
Press the lock plunger and move bracket B left to unlock it.
-
Slide ceiling plate/AP together from slots of ceiling plate.
Installation of RJ45 cable on ceiling plate
-
Plug cable into RJ45 of AP.
-
Put cable into slot of ceiling plate.
Installation of ceiling plate + AP on wall mount
-
Move bracket B to lock it with bracket A.
-
Hang the product/ceiling plate together on the wall.
Regulatory Compliance Information
Safety Notice
- Please use CSA/UL Certification Approval &LPS’s External Power Adaptor.
- Please connect with CSA/UL Certification Approval & LPS’s DC Source.
- NWA1000 is indoor use Wireless AP.
- There is a risk of fire if the battery is replaced with an incorrect type.
FCC Requirement for Operation in the United States of America
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Guideline for Human Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 31cm between the radiator & your body.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
- Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
- This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.
Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only.
Industry Canada statement
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Caution :
- the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
- where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated.
Radiation Exposure Statement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with greater than 38cm between the radiator & your body.