Shelly 581729 EM 2 Channel Wifi Energy Meter User Guide
- June 6, 2024
- Shelly
Table of Contents
Shelly 581729 EM 2 Channel Wifi Energy Meter
2 CHANNEL WIFI ENERGY METER
USER AND SAFETY GUIDE
This document contains important technical and safety information about the device and its safety use and installation. Before beginning the installation, please read this guide and any other documents accompanying the device carefully and completely. Failure to follow the installation procedures could lead to malfunction, danger to your health and life, violation of the law or refusal of legal and/or commercial guarantee (if any). Allterco Robotics is not responsible for any loss or damage in case of incorrect installation or improper operation of this de- vice due to failure of following the user and safety instructions in this guide.
Legend
- N – Neutral input (110-230V AC);
- L – Line input (110-230V AC);
- O – Output for contactor control (max 2A);
- P1+ – Positive connection of current transformer 1
- P1- – Negative connection of current transformer 1
- P2+ – Positive connection of current transformer 2
- P2- – Negative connection of current transformer 2
The Dual WiFi Energy Meter, Shelly® EM by Allterco Robotics is intended to be mounted into a standard in-wall console or next to the breakers, in order to monitor the electric power through it, independent for each channel and heavy- duty contactor control. Shelly may work as a standalone Device or as an accessory to a home automation controller.
- Purpose of control: Operating
- Construction of control: Independently mounted
- Type 1.B Action
- Pollution Degree 2
- Impulse Voltage: 4000 V
On the bottom of your Split-core transformer, you will see an arrow showing how you must place it, on the line cable. The arrow shows the direction of the current/voltage flow.
Specification
- Power supply – 110-230V ±10% 50/60Hz AC
- Max measurement per channel – 120A/230V
- Relay Max Load – 2A/230V
- Working temperature – – 40°C up to 40°C
- Radio signal power – 1mW
- Radio protocol – WiFi 802.11 b/g/n
- Frequency: 2412-2472 МHz; (Max. 2483,5 MHz)
- Operational range (depending on local construction) – up to 50 m outdoors, up to 30 m indoors
- Dimensions(HxWxL) – 39x36x17 mm
- Electrical consumption – < 1 W
Technical Information
- Control through WiFi from a mobile phone, PC, automation system or any other Device supporting HTTP and/or UDP pro-
- Microprocessor
⚠ CAUTION! Danger of electrocution. Mounting the Device to the power grid has to be performed with caution.
⚠ CAUTION! Do not allow children to play with the button/ switch connected the Device. Keep the Devices for remote con- trol of Shelly (mobile phones, tablets, PCs) away from children
Introduction to Shelly®
Shelly® is a family of innovative Devices, which allow remote control of electric appliances through mobile phone, PC or home automation system. Shelly® uses WiFi to connect to the devices controlling it. They can be in the same WiFi network or they can use remote access (through the Internet). Shelly® may work standalone, without being managed by a home automation controller, in the local WiFi network, as well as through a cloud service, from everywhere the User has Internet access. Shelly® has an integrated web server, through which the User may adjust, control and monitor the Device. Shelly® has two WiFi modes – access Point (AP) and Client mode (CM). To operate in Client Mode, a WiFi router must be located within the range of the Device. Shelly® devices can communicate directly with other WiFi devices through HTTP protocol.
An API can be provided by the Manufacturer. Shelly® devices may be available for monitoring and control even if the User is outside the range of the local WiFi network, as long as the WiFi router is connected to the Internet. The cloud function could be used, which is activated through the web server of the Device or through the settings in the Shelly Cloud mobile application. The User can register and access Shelly Cloud, using either Android or iOS mobile applications, or any internet browser and the website: https://my.Shelly.cloud/.
Installation Instructions
CAUTION! Danger of electrocution! The mounting/ installation of the
Device should be done by a qualified person (electrician ).
CAUTION! Danger of electrocution! Do not connect the cur rent
transformer clamp to the Line, before wiring it to Shelly EM. Even if only
the current transformer is connected, there might be high voltage across its
connection cables.
CAUTION! Danger of electrocution. Even when the Device is turned off,
it is possible to have voltage across its clamps. Every change in the
connection of the clamps has to be done after ensuring all local power is
powered off/disconnected.
CAUTION! Do not connect the Device to appliances exceed- ing the
given max load
CAUTION! Connect the Device only in the way shown in these
instructions. Any other method could cause damage and/or in- jury.
CAUTION! Use the Device only with a power grid and applianc es which
comply with all applicable regulations. short circuit in the power grid or
any appliance connected to the Device may damage the Device.
RECOMMENDATION! Тhe Device may be connected to and may control electric circuits and appliances only if they comply with the respective standards and safety norms.
Declaration of conformity
Hereby, Allterco Robotics EOOD declares that the radio equipment type Shelly ЕМ is in compliance with Directive 2014/53/ EU, 2014/35/EU, 2014/30/EU, 2011/65/EU. The full text of the EU declaration of conformity is available at the following inter- net address https://shelly.cloud/knowledge- base/devices/shelly-em/
Manufacturer: Allterco Robotics EOOD
Address: Bulgaria, Sofia, 1407, 103 Cherni vrah Blvd.
Tel.: +359 2 988 7435
E-mail: support@shelly.cloud
Web: http://www.shelly.cloud
Changes in the contact data are published by the Manufacturer at the official
website of the Device http://www.shelly.cloud
All rights to trademarks She® and Shelly® , and other intellectual rights
associated with this Device belong to Allterco Robotics