Shenzhen Bao Tianhua Technology MU01035 BT LED Button Headphone User Manual

: June 6, 2024
: Shenzhen Bao Tianhua Technology

Table of Contents

BT LED DESIGN HEADPHONE
Package Contents:
How To Use:
Tips:
Technical Specifications:
FAQ
FCC statement:
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MU01035 BT LED Button Headphone
User Manual

BT LED DESIGN HEADPHONE

Package Contents:

Bluetooth headphone xl
Charging cable xl
User’s Manual xl

Button Description:

“ “ : ON/OFF/Pause/Play Music
“**+** “: Short press for increase volume / long press Next song
” **-** “: Short press for reduce volume / long press Previous song

How To Use:

Power on: Press the on/off key ” ****‘ 2 seconds when it is off. The blue LED light will be on, and begin to alternate blue/red LED light. A voice will prompt “power on”, which indicates the headphone is in pairing mode.
Pairing: Activate the Bluetooth function on your phone within range and select “BT LED HEADPHONE B” from the list shown. When the blue/red LED light stops flashing it has paired successfully and you will hear “connected”. The blue LED will turn off when playing music.
Play/Pause When it is playing, press the on/off key to pause, then press the on/off key ” again to play.
Volume up: Press “+” once to increase the volume.
Volume down: Press “2 once to decrease the volume.
Previous song: Hold down the “-” to play the previous song.
Next song: Hold down the “+” to play the next song.
Phone Call: Press “ to answer/end a call. Press and hold “ ” for about 1.5 seconds to reject an incoming call.
Power off: When the headphone is on standby or operating, press and hold the center key “ ****” 3 seconds to shut down the headphone (voice prompt “power off “)

Tips:

Low Battery: LED light flashes in red.
To Charge:

Insert the USB connector end of the included cable (see packing list) into the USB jack on the charger or USB port on the computer.
The indicator light will be red while charging.
When the headphone is fully charged, the indicator light will turn off from being red.
Please unplug your charger from the power source.
Please use a qualified charger to recharge your headphone, If not. it may result in damage or even an explosion.
Repeated charging and discharging of the headphone will lead to decreased battery life over time, which is normal for rechargeable batteries.
You must charge the Bluetooth Headphone if it has not been used for more than 6 months.

Technical Specifications:

Range 33ft / 10 m
Battery Capacity: 200 mAh
Voltage: 3.7 V
Play Time: 4-5 hours
Charge Time: 2 hours
Charging Input:5V 150 mA
Frequency Response: 20Hz-20KHz
Operating temperature range: 0-45 C

FAQ

Why can’t I start my Bluetooth headphone?
Answer: Please ensure that the headphone is fully charged for your first use.
Why won’t sound come out of the headphones?
Answer: Check whether the playback device and the Bluetooth headphone are successfully established. If the audio device is not properly connected, please reconnect. Please also adjust your mobile phone or Bluetooth headphone volume to a suitable volume level.
Why can’t I find these headphones in my Bluetooth options?
Answer: Make sure the Bluetooth is in `visible mode”. If no pairing occurs, the Bluetooth function will automatically shut off. Please reopen Bluetooth to “visible mode”. If there is a program error, please reboot your phone, and if the program error is caused by your Bluetooth headphone, please restart the headphone.

FCC statement:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.lf this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off ancon, the user is encouraged to try to correct the interference by one or more of t the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

WARNING:

Charge and operate only as indicated in this manual, as improper use may result in damage to the product or injury.
To avoid the risk of shock or injury, do not dismantle the device or insert any objects into the Headphone.
To avoid electronic interference and/or compatible conflicts, turn off the product in any facilities where posted notices instruct you to do so.
Do not pull the Headphone charging cable. Damage may result to the cable.
Keep out of reach of children. This is not a toy.
Avoid exposure to moisture, liquids, heat, flame, and high voltage equipment.
Retain these instructions as they contain important information.
Do not short circuit the input terminals of the Headphone.
Do not drop, place heavyweight or allow a heavy impact to the Headphone.
PCB of the battery should not be crushed and twisted.
The battery body should not be Bended.
Do not disassemble and Do not dispose of in fire.
Do not use the product while driving or crossing the road.

RF warning statement:
The device has been evaluated to meet general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.

FCC ID: 2A2H6-MU01035
301, Building Plant No.5 Anliang Road, Xi Keng Community, Longgang District, Shenzhen, Guangdong, China
Keep All Relevant Information For Future Reference.