Whetron Electonics S100371700T1 Smart Key System Host Instructions
- June 6, 2024
- Whetron Electonics
Table of Contents
Wheaton Electronics
FCC Statement:
-
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
-
(1) This device may not cause harmful interference, and
-
(2) this device must accept any interference received, including interference that may cause undesired
operation. -
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
-
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
-
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-
–Reorient or relocate the receiving antenna.
-
–Increase the separation between the equipment and receiver.
-
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-
–Consult the dealer or an experienced radio/TV technician for help.
-
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Turn on the motorcycle power
- Press the Keyless button “ KEYLESS“ when the smart key is within the operating range.
- The buzzer will sound twice and the “Turntable “ will be unlocked automatically when the smart key is authenticated.
- The motorcycle power will be on and the speedometer will be turned on also after the Turntable is changing to the position.
- It is ready to start the engine.
Turn off the motorcycle power
1) After the Turntable is changed to position the power will be turned off.
- Press the power button ” “when the smart key is within the operating range.
- The buzzer will sound once the smart key is authenticated.
How to lock steering lever
- Press the Keyless button “ KEYLESS“ to lock the “Turntable “
- After sound once of buzzer after the lock succeeds.
Smart key operating range
Remotely:0~1.5 m (as show right side)
Immobilizer Sensor :0~2.5cm
The smart key close to the position on the motorcycle (as shown below location
on the motorcycle right side) within 2.5cm
SMART KEY SYSTEM: Host +Smart key
P.C.B (Front)
P.C.B (Back)：
Smart Key battery
Button cell battery: CR2032
Button cell battery CR2032
Cautions:
- To prevent electric shock or short circuit damage, please ask a qualified technician for installing it.
- Please use an independent power supply so that the failure caused by the unstable power will not occur.
- Metal will block the radio signal. Therefore, stay away from metal when installing the product. Remote control distance will also become shorter when there is a same frequency signal around.
- Adjacent products should be separated at least 3 meters.
- If there is a malfunction of the product, please contact the service department.
Functional checklist
NO.
| Check Items| Detail items| Condition| Operation(Input)|
Result
| |
---|---|---|---|---|---|---|---
1| HOST| Identification Fail (Immo Coil)| l Power input 12V±0.1Vl Place the
smart key on the surface of the Immo. Coil 2.5mm l The smart key need to
remove the battery or disconnect the LF antenna。| 1. Move the smart key away
from the sensing area(more than 5cm)2. Push power bottom at 300ms| If
identification fails the host goes into standby and does not do anything.| □OK
□NG| Immo sensing Distance 8cm
2| HOST| Identification Fail (Immo Coil)| l Power input 12V±0.1Vl Place
the smart key on the surface of the Immo. Coil 2.5mm l The smart key need to|
Move the smart key away from the sensing area(more than 5cm)。| 1.
Identification after every 3 seconds2. If identification fail system will lock
3. The buzzer sounds for 500ms.| □OK □NG|
Remove the smart key more than 10 cm.
| | | remove the battery or disconnect the LF antenna.l If identification
Pass, system unlock| | 4. Red LED lights up for 2 seconds5. Extinguish the
blue LED。| |
---|---|---|---|---|---|---|---
3| HOST| Lock(Immo Coil)|
l Power input12V±0.1V
l Place the smart key on the surface of the Immo. Coil 2.5mm l The smart key
need to remove the battery or disconnect the LF antenna。
| Turn the dial to switch the IGN status IGN OFFàIGN ON àIGN OFF one time.| 1.
Identification after
every 3 seconds.2. If identification fails the system will lock.3. The buzzer
sounds for 00ms4. Red LED lights up for 2 seconds.5. Extinguish the blue
LED.| □OK □NG|
4| HOST| Unlock(Immo Coil)| l Power input 12V±0.1V| Change IGN OFF/IGNOFF2
Switch to IGN ON| 1. System will lock2. Blue LED will light up slowly| □OK
□NG|
5| HOST| Identification Pass(Antenna)| l Power input 12V±0.1V.l Place the
smart key within the surface of the LF antenna 150cml The lock is locked.|
Power Bottom pressed 300ms| 1. If identification is successful, the drive
lock is unlocked, and the blue LED will slowly light up2. Buzzer short beep
2(ON/OFF:100ms/100ms)| □OK □NG|
6| HOST| Identification fail(Antenna)| l Power input 12V±0.1Vl Place the
smart key outside the surface of the LF antenna 300cm. l The lock is
locked.|
1. Place the smart key outside the surface of the LF antenna 300c2. Power Bottom pressed 300ms.
| If identification failed, no action is taken, the host goes on standby| □OK
□NG|
7| HOST| Identification Margi(Antenna)| l Power input 12V±0.1V
l Place the smart key within the surface of the LF antenna| 1. Power Bottom
presses 300ms for system unlock.
2. Place the smart key| 1. The system first recognizes the unlock and then
enters the 3-second identification.| □OK □NG|
| | | 150cm.l The lock is locked.| the surface of the LF
antennawithin230cm~260 cm, and press the power button again.| 2.After counting
2 seconds, press the Power Button to perform the locking action.3.The system
performs lock, and the buzzer sounds for 500ms. 4. Red LED light up for 2
seconds.5. Extinguish the blue LED.| |
---|---|---|---|---|---|---|---
8| HOST| Identificaton fail(Antenna)| l Power input 12V±0.1Vl Place the
smart key within the surface of the LF antenna 150cm.l Identification first,
after the system is unlocked.| Place the smart key outside the surface of the
LF antenna 300cm.| 1. Identification after every 3 seconds of counting. 2.
Identification failed, system execution lock3. The buzzer sounds for 500ms.
Red LED light up for 2 seconds.5. Extinguish the blue LED.| □OK
□NG|
9| HOST| Lock(Antenna)| l Power input 12V±0.1V| Change IGN OFF/IGN OF2
Switch to IGN ON.| 1. System execution lock. 2. The blue LED will slowly
light up.| □OK □NG|
10| HOST| Lock| l Power input 12V±0.1l Place the smart key surface of the
Fantennawithin150cm~300 cm.| If the turntable is pressed, touch the
positioning signal Pull Low.| The system cannot perform locking.| □OK
□NG|
11| HOST| Lock| l Power input 12V±0.1Vl Place the smart key within the
surface of the LF antenna 150cm.| 1. Power Bottom pressed 300ms 2.
Positioning signal Pull Low.| 1. Red LEDON/OFF
(500ms/500ms)continued 10 seconds.2. Buzzer sound ON/OFF (500ms/500ms)
continued 10seconds.| □OK □NG|
| | | | | 3. System power off.| |
---|---|---|---|---|---|---|---
12| HOST| Lock| l Power input 12V±0.1Vl Place the smart key within the
surface of the LF antenna 150cm.| 1. Power Bottom pressed 300ms.2.
Positioning signal Pull Low.3. During the warning reminder time, after the
positioning signal Pull Lowis released| 2. The buzzer sounds for 500ms. 3.
Red LED lights up for 2 seconds.| □OK □NG|
13| HOST| Lock| l Power input 12V±0.1Vl Place the smart key within the
surface of the LF antenna 150cm l Turn the dial to switch the IGNstatus OFF
ON OFF one time.| 1. Power Bottom pressed 300m2. Positioning signal Pull
High.| 1. System execution lock.2. The buzzer sounds for 500ms.3. Red LED
lights up for2 seconds.| □OK □NG|
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device contains license-exempt transmitter(s) that comply with the FCC
Rules and Innovation, Science and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions: (1) this device
may not cause interference, (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>