OKASHA Smart Valve Controller User Manual
- June 4, 2024
- OKASHA
Table of Contents
OKASHA Smart Valve Controller
Thanks for choosi ng our Smart Valve Controller, please read this manual carefully before using it
Product specifications
-
Power supply voltage
12V/1A -
Communication technology
WIFI 2.4g -
Val ve pressure
1.6 mpa -
Val e speci ficat ions
4, 6, 1 inch, 1.25 inch -
Close valve time
5-10 seconds -
Open valve time
5-10 seconds -
Torque
30-60 kgfcm -
Applicati on System
IOS/android
How to Install
-
Install the bracket on the install ati an ear of the smat valve controller (screw is not tightened first).
-
Fix the mounting bracket and the water pipe or as pipe (as shown in the figure).
-
Adjust the position of the smart valve controller, please make sure the smart valve handle fits securely over the valve handle. Ensure that the center line of the smart
valve controller and the center line of the valve are in the same line, otherwise, the valve cannot be fully opened and closed. -
Then tighten the screw at both ends of the mounti ng bracket. After the installation of the smart valve controller, manually pull down the clutch pull ring,
Swing the smart valve controller transfer handle, please check if the valve s switch is in place. -
Tighten the screw of the smart valve controller handle clip according to the diagram.
-
Connect the power adap ter. The smart valve contoller can be controlled (Open/Close) by pressing the red button
-
If power is cut off, then ring under the smart val ve controller can be manually pul led down and swing the tran sfèr handle to close or open the valve.
How to Integrate with the App
- Down load “Tuya Smart” or “Smart Life” APP (scan the QR code or download the APP from Google Play/iOS), create new Account ID and password to login (if not already registered)
- Add device Click “+”, select “Other” from the bottom tab and then select “Others (Wi-Fi)”.
- Press the power button of the smart valve for about 5 seconds until the indicator light flashes quickly, smart valve controller enters into pai ri ng stat e
- Select your Wifi SSID, Inp ut WIFI password, and proceed to the next screen. (NOTE: The device supports only 2.4G Wi-Fi)
- Connect ion ruming, wait about 30-60 seconds until the device connects successfully, Perfect!!
- You can select “Auto Scan” Mode, According to the prompt, the smart valve controller will be connected to the network automatically
How to link with other smart devices
- Please open “Tuya Smart” or “Smart Life” APP and click the “Smart” tab located on the mid-bt tom of APP SCTec
- Click “+” (top right of screen) to create a link with other smart devices.
- Select “When device status change” and select a device that you want Smart Valve to connect. i.e. Smart Water/flood sensor.
- Select the status of the device (On/Of).
- Then Select “Run the device” and select smat valve control er.
- Click “Next” and finally “Save”‘. Perfect!! You created a smart connection between Water leak sensor and water valve.
- Whenever water leakage is detected te d, with this smart linkage water valve will close automatically.
- Similar linkages can be created with other sm art devices.
FAQ
-
Q. The valve controller switch is not in place
Ans. Please check whether the smart valve controller center and the val ve center are aligned. If they are not aligned, then na only it will make the valve switch
not work properly but also bum the smart valve
control let’s motor. -
Q. The valve switch is stuck.
Ans: Please pull down the clutch pull ring and swing the smart valve controller’s handle 90 degrees until the valve can be switched smoothly. If the valve is too tiht, please
apply some grease to it or replace it. -
Q.The smart valve controller cannot be paired to the network.
Ans: Please make sure you’re using 2.4Ghz WIFIL Si signals are pres ent and strong, and the password is correct.
While the smart valve controller is in pairing mode, please keep it as close to the outer as possible. (for best possible results). Please follow the instructions as given above. -
For other troubleshooting problems, pl ease read the
Smart Life or Tuya APP’s help center in detail.
Packing list
- Smart Val ve Contol ler
- Instructi ons
- Adapter 12V/1A
- Pipe clips(clamp)
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the cquipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This cquipment should be installed and operated with minimum 20cm distance between the radiator and your body: Use only the supplied antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>