Shenzhen Kinlan Technology BE1036 Twin Wireless Earbuds with Charging Case User Guide

**Shenzhen Kinlan Technology BE1036 Twin Wireless Earbuds with Charging Case User Guide

**

What’s in the box?

• Wireless Earbuds

• Charging Case

• Ear tips (S,L)

• Small Ear hooks

• Ear loops

• Type-C Cable
  

• User Manual

Product Diagram

1. LED Indicator / Microphone

2. Touch Area

3. Charging Pin
   

4. Type-C charging port

5. LED Indicator

Charging

Earbuds automatically charge in case

• Remove the protective film from the earbuds when using for the first time.
• Fully charge both earbuds and the charging case before the first-time using.
• To prevent damage, use the provided USB-C cable.
• Fully dry off the earbuds and the USB port before charging.

Charging Case Indicator

The charging case indicator will automatically turn off when the earbuds fully charged.

How to fit?

1. Identify the left and right earbuds
2. Rotate the earbuds, and adjust to find the best angel
3. Make sure the ear tip seals in the ear canal
   

Power On / Power Off

• Both earbuds will automatically turn on while open the charging case(with the Green LED lights flashing).

• Put the earbuds back to the charging case and close the lid to turn them off.
  

• In the shutdown status and when the earbuds are not in the charging case. Simultaneously click and hold the MFB of both earbuds for 3 seconds to power on (with the Green LED lights flashing).

• If the earbuds are not in the charging case. Pause music first, click and hold the MFB of both earbuds for 3 seconds to turn them off.
  

Pairing your earbuds

• Both earbuds will automatically turn on (with the Green and red LED lights flashing) and start pairing while open the charging case.
  

• Select “BE1036” from the list of devices shown
  
  Each earbud could be used independently
  Note:
  The earbuds will automatically connect with the device their last paired with when earbuds are power on.

Function

Play/Pause|

| Single Click(L or R)
Next Song| | Double Click(R)
Previous Song|

| Double Click(L)
Volume up/down| Long press L/Long Press R

Answer/End Call|

| Single Click(L or R)
Reject Call|

| Double Click(L or R)

Siri/Google Assistant|

| Triple Click(L or R)

Reset and Reconnecting

If you fail to build connection between two earbuds, or between two earbuds and your phone, please try the follow step:

1. Delete the old connection on your device.
2. Power on both earbuds, quick click Left or Right earbuds 5 times when they are in pairing mode.
3. Turn on your smart devices and select “BE1036” to confirm pairing.
   

Specification

ln-put

|

DC 5V/1A

---|---

Wireless Version

| V5.1
Support Profile|

A2DP,AVRCP, HFP, HSP

Maximum Working Range

| 10m(without obstacle)
Earbuds battery life|

Up to 6 hours(various by volume and audio content)

Earbud Charging Time

| About 1.5 hours
Earbud Battery Capacity|

50mAh

Charging Case Battery Capacity

| 500mah
Case Charging Time|

2 hours

Charging Case Recharge Earbuds

| 3-4 times
Product Weight|

83g

FCC Warning

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

The device has been evaluated to meet general RF exposure requirement.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>