Hebei Huachuangda Technology HCD-1215L1CON Controller User Manual

Hebei Huachuangda Technology HCD-1215L1CON Controller User Manual

HEBEI HUACHUANGDA TECHNOLOGY CO.LTD HCD-1215L1CON CONTROLLER INSTRUCTION

The electronic board is used for kid car, and controls kid car to move forward, move back, swing. Also, can adjust speed accordingly.
Power by battery to drive motor, turn via motor too.

1. use right adapter to recharge the battery, keep the value belong to 6-12 voltage output .And keep away from children when recharging.
2. Pay attention to the color wire to connect, take care of positive pole and negative pole. Bus line, jumpers connected correctly.
3. Do not dip into water, in case of shortcut.
4. Do not expose the board under rainy, under sun.
5. Press the button power firstly, the car is stand by. Press rock button, the kid car swing from time to time, until the run button is pressed.
6. Under the run status, step on the pedal to accelerate, loose to decrease speed. At the same time, pust the rocking bar to forward or back.
7. From the acousto-optic wire, the board can receive blue tooth signal in 2.4G frequency, and operate the kid car to move. That means, the remote control box can treat, and cell phone can treat via APP.

Specification:

Supported type:| Bluetooth low Energy
Modulation:| GFSK
Operation frequency:| 2402MHz to 2480MHz
Channel number:| 40
Channel separation:| 2 MHz
Max Peak Power:| -3.0dbm

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) thi s device may not cause harmful interference, and (2) this device must accept any interference received, incl uding interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy a nd, if not installed and used in accordance with the instructions, may cause harmful interference to radio com medications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
‐ Reorient or relocate the receiving antenna.
‐ Increase the separation between the equipment and receiver.
‐Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
‐Consult the dealer or an experienced radio/TV technician for help important announcement

Important Note:

Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Country Code selection feature to be disabled for products marketed to the US/Canada.
This device is intended only for OEM integrators under the following conditions:

1. The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2. The transmitter module may not be co-located with any other transmitter or antenna,

As long as the two conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.

Important Note:

In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

End Product Labeling

The final end product must be labeled in a visible area with the following” Contains FCC ID: 2A2MNHCD-1215L1CON”

Manual Information to the End User

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.

Integration instructions for host product manufacturers according to KDB

996369 D03 OEM Manual v01

2.2 List of applicable FCC rules

CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to

the modular transmitter

2.3 Specific operational use conditions

This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system.

2.4 Limited module procedures

This module is Limited single modular without shielding, host manufacturer have to consult with module manufacturer for the module limiting conditions when integrate the module in the host. module manufacturer should reviews detailed test data or host designs prior to giving the host manufacturer approval.

2.5 Trace antenna designs

Not applicable

2.6 RF exposure considerations

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

2.7 Antennas

This radio transmitter FCC ID:2A2MNHCD-1215L1CON has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Model

|

Type

|

Connector

| Peak gain ( dBi )
---|---|---|---
2400-

2500MHz

| 5150-5250

MHz

| 5250-5350

MHz

| 5470-5725

MHz

| 5800

MHz

BLE| PCB| /| 0 dBi| /| /| /| /

2.8 Label and compliance information

The final end product must be labeled in a visible area with the following” Contains FCC ID:2A2MNHCD-1215L1CON”.

2.9 Information on test modes and additional testing requirements

Host manufacturer which install this modular with limit modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C:15.247 and 15.209 requirement, only if the test result comply with FCC part 15.247 and 15.209 requirement, then the host can be sold legally. 2.10 Additional testing, Part 15 Subpart B disclaimer
Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>