danielle Bluetooth LED Vanity Mirror Instruction Manual
- June 6, 2024
- danielle
Table of Contents
Instruction Manual
66″× 16.5″ FRONT
USER MANUAL
MANUAL DEL USUARIO
Please read all instructions carefully before operating.
Sirvase leer cuidadosamente todas las instrucciones antes de utilizarlo.
Included:
1 x Bluetooth L.E.D. Vanity Mirror
1 x USB Cable
1 x User Manual
Caution:
- The mirror is made of glass; therefore handle with care.
- Adult use only. Not intended for use by children.
- Do not expose the mirror to direct sunlight while unattended; reflected sunlight may cause a fire.
- Gently press the power button; do not press hard.
- Use a soft cloth to clean the mirror surface when needed.
- Avoid heat, humidity, and damp areas.
- Stop using the mirror immediately if it malfunctions or is damaged in any way.
- Use care when using L.E.D. lights; extended use/prolonged exposure directly into eyes may cause damage.
TROUBLESHOOTING
| PROBLEM | POSSIBLE REASON(S) | SOLUTION |
|---|---|---|
| L.E.D. light bulbs are flickering. | The battery is not sufficiently charged. |
Plug into a power source via the USB cable
provided and wait at least 20 minutes, or until the mirror is fully charged
for best results.
The wireless charge functions not working.| The mirror is not plugged in (the
charging function will only work when connected to a power source).
The smartphone case, holder, or cover is too thick for the wireless function
to connect properly.
The smartphone does not have wireless charging capability. The smartphone was
placed inside the stand vertically.| Plug into a power source via the USB
cable provided.
Remove phone case, holder, or cover before charging.
Wireless charge function will not work with smartphones that do not have
wireless charging capability. The charging feature works best if the
smartphone is placed inside the stand horizontally.
Bluetooth is not connecting.| Bluetooth is not enabled on your smartphone.
Another user is already connected.
The battery is not sufficiently charged.| Enable Bluetooth on your smartphone.
Disconnect on current user’s smartphone, and connect via new user’s
smartphone.
Plug into a power source via the USB cable provided and wait at least 20
minutes, or until the mirror is fully charged for best results.
The phone call function is not connecting to the mirror/microphone/ speakers.|
Incoming call was answered on the smartphone device, instead of using the
mirror call button.| Receive calls using the phone button located on the back
of the mirror, OR connect to Bluetooth in your smartphone settings once the
call is answered and/or a call is placed.
DIRECTIONS:
1. FULLY CHARGE battery via the provided USB cable prior to first use.
2. Plug the provided USB cable to a power source (NOTE: avoid using a
computer USB input). The other side of the plug connects to the backside of
the mirror.
3. Use the touch power button on the front of the mirror face to turn on the lights. Keep pressing for 3 different light levels or to power off. Lights will turn off automatically after 5 minutes of inactivity.
4. Enable Bluetooth on your smartphone and connect to “Danielle Beauty Mirror” to make calls, watch videos, or listen to music through our high- quality speaker. 1 beep will indicate that the Bluetooth is connected. 2 beeps indicate disconnection.
Button: Long press to increase the audio volume. When listening to music,
short press to skip forward a song.
Button: Short press to play or pause audio (song or video). This button also
answers or ends a phone call (short press).
Button: Long press to decrease the audio volume. When listening to music,
short press to skip back a song.
Button: Long press to turn on or off Bluetooth function. 1 beep will indicate
that the Bluetooth is connected. 2 beeps indicate disconnection.
• Microphone: Ensure close proximity for best sound quality when making phone
calls.
NOTE: For incoming phone calls, use the button to answer if you wish to
use via the mirror speaker/microphone. If you answer the call directly on your
smartphone, it may not connect to the mirror speaker/microphone.
CONTROL BUTTONS ARE LOCATED ON THE BACK OF THE MIRROR.
6. Use the convenient stand on the front of the mirror for hands-free mirror usage; this will also begin the charging function. You may have to remove your case/cover (if applicable) before charging. The charging feature works best if the phone is placed inside the stand horizontally, as pictured. Wireless charging will only work if the USB cable is plugged in.
7. This mirror contains an internal battery pack that is rechargeable by the provided USB cord. A RED light on the back of the mirror indicates when it is in charge mode; a BLUE light indicates when the mirror is fully charged. When charged, both Bluetooth and mirror lighting will function unplugged. The USB cable must be plugged in for the wireless charging function to work.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party.
Responsible for compliance could void the user’s authority to operate this
equipment. (Example- use only shielded interface cables when connecting to
computer or peripheral devices). This equipment complies with Part 15 of the
FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
FCC Radiation Exposure Statement:
The equipment complies with FCC radiation exposure limits set forth for
uncontrolled environments. This equipment should be installed and operated
with a minimum distance of 20cm between the radiator and your body.