Kingta Technology F2 Waterproof Wireless Speaker User Manual
- June 6, 2024
- Kingta Technology
Table of Contents
Waterproof Wireless Speaker
User’s Manual
Introduction
Thank you for choosing the F2 as your source for entertainment, you can use this item with iPads,iPhones, iPods, and many types of smart-phone to stream music, and enjoy hands-free calling. In order to get the best results when using the device, please read this manual first before using it.
Features
-Volume and song control directly on the speaker unit
-Stunning sound clarity
-Ultra-portable design
-Great for parties, indoor and outdoor
-Allow you to make and answer phone calls
- Previous / Volume –
- ON/OFF button
- Next / Volume +
- Green LED(AUX)
- Red LED(Charging)
- Blue LED(Bluetooth)
- Phone /play button
- MIC
- Micro USB Charging/AUX-in Port
Included:
- Speaker
- SB Micro Charging Cable
- 3.5 mm Micro-USB Cable
- User Manual
Specifications
Supported Profiles:A2DPV1.2 ,AVRCPV1.4, HFPV1.5,HSP1.2,GAVDP1.2
Bluetooth Range:33ft (10m)
Dimensions: 2088080 mm
Battery: Li-Ion .7V/2000mAh
Charging: 5V @ 1 A
Operation
Powering On
Press and hold the “ON/OFF” button for 2 seconds to power ON, the Blue LED
will start to flash.
If an AUX (3.5 mm) cable is connected to the unit, the Blue LED will turn off,
and the Green LED will stay illuminated, notifying you the unit is in Aux-In
mode.
Powering Off
Press and hold the “ON/OFF” button for 2 seconds to power OFF
Bluetooth Mode
Pairing
The unit will automatically go into “Pairing Mode” when it is powered ON.
Go into your Bluetooth device settings menu and look for “F2”
After the unit has paired and connected, it will re-connect automatically when
the unit is powered on and the device is in range.
Note: Bluetooth Timeout:10 minutes
Begin Streaming Music
Press “ ” to start playing music.
Press and Hold “ +” for 2 seconds to play the next track.
Press and Hold “- ” 2 seconds to play the previous track.
Press either “+ ” or “- ” for volume control.
Making and Receiving Phone Calls
When the unit is connected and paired to your device, the unit allows you to
make or receive phone calls with its built-in microphone.
Press “ ” to accept a call
To end a call press“ ”
To place a call, simply dial the number or select a contact form
To reject a call, press and hold “ ” for 2 seconds
Aux-In Mode
Plugin the supplied 3.5 mm cable into the unit. The other end is connected to
your device. The Green LED will stay illuminated.
It means in “Aux” mode.
Please note music can be controlled by your device.
Charging
Attach the USB cable to the unit, and plug it into any USB charger. If the
unit is completely discharged, it will take approximately 4 hours to fully
charge.
The Red LED will illuminate during charging when it has completed, the Red LED
will turn off.
Note: There will be a beep when the battery is low and needs to be
recharged.
LED Status
Blue LED sold | Bluetooth Mode |
---|---|
Green LED and solid | At Mode |
Red LED | Ctagird |
**Troubleshooting
**
The unit doesn’t connect to the device| Speaker needs to be connected/
re-pared to device
---|---
Atone is heard every few seconds| Speaker needs to be charged
Unt veil not power on| Speaker needs to be charged
The unit doesn’t control rock(s)volume| Speaker needs to be in &afoot,
made for hi control
Unit distal at high volume| The devices’ volume needs to
be lowered
FCC Statement:
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: 1) this device may not cause harmful
interference, and 2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
– Reorient the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>