Best Case Accessories 20019 Magnetic Wireless Power Bank User Manual

: June 6, 2024
: Best Case Accessories

Table of Contents

Power Bank Layout
Suitable for
Features
To Charge Power Bank
To Charge Phone or USB Device
To Check Remaining Capacity
Important Safety Instructions
FCC Warning
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**Best Case Accessories 20019 Magnetic Wireless Power Bank User Manual

**

Printed black & white, one sided & folded accordion style with Photo Image page as front.
Each page 57mm by 100mm or paper is 285mm across by 100mm high when cut for folding.
NOTE: Red lines are die-line guide (on its own layer) to be deselected before printing.

Power Bank Layout

USB Output
USB Input C
Micro-USB Input
Wireless Output
Power, Switch

Suitable for

Smartphones
Smartwatches, fitness trackers, digital camera
Portable Bluetooth” devices
Portable hand-held gaming consoles

Features

Capacity: 5000呤Magnetic Power Bank
Battery type: Lithium polymer
Rechargeable > more than 300 t,mes
Includes Mic「o-USB cable for charging
Built-in over charging and short circuit protection
Input·Micro/USB-C”: DC 51/ 2A
Output: USB – DC 5V 2.4A max / wireless 5W
Charging time. About 3-4 hours

Bluetooth and associated product marks are the trademarks of independently owned and operated companies. This product has not been licensed or endorsed by the manufacturer of Bluetooth products. MagSafe is a trademark of Apple Inc. registered in the U.S and other Countries. USB-C is a registered certification mark of the USB implementer Forum.

To Charge Power Bank

Charge Via USB Wall Charger

Using the included Micro-USB cable, connect the USB connector, to an AC wall adapter, o, USB port on a computer.
Connect the Micro-USB connector, to the input connector, on the Power, Bank
During charging, the LEDs will flash to show charging status
When charging Is complete, the LEDs w,11 be permanently on using a standard USB-C’cable

To Charge Phone or USB Device

To Charge a Mobile Phone or other USB Device by Cable

Charge by Wireless Output MagSafe Compatible Devices.

Using your phone or other USB device’s charging cable, connect the USB Type A connector to the Output connector on the Power Bank.
Connect the other end of the cable to your device
Charging should commence automatically.
Pressing the power button will also start up or stop charging
If your phone or device uses a standard Micro-USB connector then you can also use the included cable to charge your device
When your phone or device is fully charged, the Power Bank will automatically turn itself off.
Wireless/magnetic charge applies only to phones that have this feature (MagSafe compatibility).
Place the Power Bank on the back of the phone and align to verify charging has begun. Once the Power Bank is connected make sure to have the USB ports facing down for better contact.

To Check Remaining Capacity

Press On/Off button and LEDs w,ll light to show remaining capacity.
The LEDs will turn automatically after, about 35 seconds or pressing On/Off Button twice will tum off the LEDs Immediately.

LED ON Off Flashing	Remaining Capacity
Less Than 25%

| 25% to 50%
| 51% to 75%
| 76% to 100%

Important Safety Instructions

To maximize battery life span, fully charge Power Bank before first use
Store Power Bank in a cool and dry place
Do not store Power Bank in hot or humid environment.
Do not charge and discharge at the same time
Do not charge Micro-USB and USB-00 at the same time
Operating temperature should be between 14F to 104F.
If Power Bank is not used for long periods of time, you should charge and discharge once every three months
When charging a device, the Power Bank may feel warm, this is a normal operating condition and should not be cause for concem
In normal conditions, the battery performance will decline over several years
Do not dispose of Power Bank in heat or fire
Do not clean Power Bank with harmful chemicals or detergents.
Misuse, dropping or excessive force may cause product damage.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate tadio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
- Reorient or relocate the receiving antenna,
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an expenenced radio/TV technician for help.