Wanma Yun Electronic Technology SLU-T1000 UWB Tag User Manual

: June 6, 2024
: Wanma Yun Electronic Technology

Table of Contents

Product Specification
Product Picture
Warning
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Wanma Yun Electronic Technology
SLU-T1000 UWB Tag
User Manual

Product Specification

Specification|
---|---
Dimension| 47.323.38.5 mm
Battery| 70mAh
Charging| Wireless charging
IP Grade| IP68
Working Environment| Working Temperature: -10-60°C Humidity:10%-90%
UWB Specification|
Frequency Band| CH2: 3993.6MHz; CHS: 6489.6MHz
Speed| 6.8Mbps
Transmitting Frequency| 2 times per second(Can be modified)
Output Power| 5-41.3dBm/MHz
Channel| Support channel 2&channel 5
Protocol Standard| IEEE 802.15.4-2011 UWB
RFID Specification|
Frequency Protocol Standard| 13.56MHz Mifire

Product Picture

Product Picture

LED: status
Charging: Red
Full: Green
Low light reminder Red: (1 per second Flash)
Please Charge our tag on wireless charging when LED flashes red.
The UWB positioning system includes UWB Tag, UWB Anchor, and server. The positioning system is based on TDOA work.
In TDOA, tags send periodic blink messages that are received at the anchor node. Anchors report blink reception time-of-arrival (TDOA) timestamps to the server. The server multilaterates to estimate the tag location and report it with the tag ID through a defined API.

This UWB Tag is used for swimming caps in the Swimming Center as indoor use only.

Notices:

This device (Location tag) is a kind of tag based on UWB technology with a high precision location.
This product meets the design requirements on environmental protection, Product storage, use, and disposal shall comply with relevant national laws, regulations, requirements.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This is not a handheld device. Do not hand-held it.
This UWB system needs to be professional installation, and we provide free
technical support to install this product indoors. During debugging by software, the using zones will be strictly controlled indoors. When the UWB Tag leaves the indoor area covered by the base station, the UWB function of the Tag will stop work immediately.
UWB positioning system includes UWB Tag, UWB Anchor, and server. The positioning system is only used indoors, and the emissions from equipment operated would not be intentionally directed outside of the building in which the equipment is located.
It is forbidden to use the antenna installed outdoors.

Warning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modify cations to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information The device has been evaluated to meet general RF exposure requirements.
“This equipment may only be operated indoors. Operation outdoors is in violation of 47 U.S.C. 301 and could subject the operator to serious legal penalties.”