Positioning Universal TM95M GPS Tracker User Manual
- June 6, 2024
- Positioning Universal
Table of Contents
Positioning Universal TM95M GPS Tracker
Introduction
ID and Tooling Design
Dimensions: 83.5mm47.5mm18mm
Hardware
Physical and Electrical Specifications
Input Voltage: 7-36VDC
Power consumption:
– Active mode: 100mA @12VDC
– Sleep mode: <5mA @12VDC
Operating temperature: -30℃ to 80℃
Storage temperature: -30℃to 80℃
Input/Output
Download and debug port: 1
SWD Interface: 1
Function LEDs: 2
GPS Status Green
Cellular Status Orange
Buzzer:1
Input:1
Output:1
Cellular Communication
Operation mode :LTE/GPS
Operation band :LTE B2/B4/B12/B13/B25;GPS 1.57542GHz
Modulation: QPSK/16QAM
Harnesses
There are 1 harnesses that may be used with the TM95M-4:
1.4 wire power and I/O harness
Event Codes
The table below relates the Event codes in the message to the reason the message was generated:
Message # | Message Type | Description |
---|---|---|
0 | Interval | Auto Report (auto report when moving) |
1 | Interval | Vibration alarm(report when GPS is OFF and vibration detected) |
2 | Power Disconnect | Power cut alarm (report when external power is cut off) |
3 | Power Connect | Power connected alarm (external power has been connected) |
4 | Ignition ON | Hardwired or Virtual Ignition ON detected |
5 | Ignition OFF | Hardwired or Virtual Ignition OFF detected |
6 | Input High | Input high alarm |
7 | Input Low | Input low alarm |
System network structure
GPS alarm is current ly t he m ost advanced securit y Set t ings. GPS alarm m ore expensive than ordinary burglar alarm , and need to pay the additional service fee, so t he popularit y is not high. And alarm is based on a GPRS net work com m unication network, com bining with the intelligent linkage of m obile phone and car anti- theft, this kind of alarm alarm is not restricted by distance, overlay net work is wide, but need t o pay t he m ont hly rent al. Buying guide t o edit GPS alarm when t he choose and buy, need t o pay at t ent ion t o is t he com parison of several com m on GPS perform ance.
Appearance and installation instruction
USER MANUAL
Introduction
This chapter is user manual for TM95M.
One DC 12V cable.
Connect the DC 12V cable to the connector of J101 on the device, the other
side connect to
DC 12V, you can use the DC 12v cable to supply power.
FCC Regulations
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. This equipment has
been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/ TV technician for help. Changes
or modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To comply with FCC RF Exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for the transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.