deako Master Smart Dimmer User Manual

deako Master Smart Dimmer

Get to know your Deako SwitchInsert a switch

Align the blue tab on the backplate with the top of LED keyLED key

How many switches control this light?

Insert a switch

1. Align the blue tab on the backplate with the top of the switch
2.  While pressing the switch inwards, push in the blue tab

Installation complete! Now let’s get smart.

Pairing
Control your new smart switch by downloading the Deako App.

What you’ll need

Switch types

Identify the switch type by looking at the sticker found on the back of your switch.
You will either have a Master Smart Dimmer or Remote Smart Dimmer.
If you have a different type of switch, go to support.deako.com for more information

Remove existing dimmer

1. If there is a switch installed in the backplate you want to upgrade, start by pulling the corner of the faceplate

2. Pull the blue tab outwards to release the switch Insert Remote Dimmer

3. Locate the powered backplate in the circuit by inserting a Remote Smart Dimmer into a backplate in the circuit.
   Align the blue tab on the backplate with the top of the switch

4. While pressing the switch inwards, push in the blue tab
   If the backplate is powered, the switch will flash green
   If switch does not flash green, move to the next location & repeat step 1

5. Wait until the switch stops flashing green, then press & hold the configure button until it flashes purple

6. Move to the next powered backplate, then repeat steps 1-5 for each switch in the circuit until you get to the last switch Insert Master switch

7. On the last switch in the circuit, insert the Master Smart Dimmer

8. Wait until the switch stops flashing green, then press & hold the configure button until it flashes purple

9. Once all switches in the circuit are flashing purple, continue to step 9 are flashing purple, press & hold the configure button on any switch until it flashes white
   Once the switches show solid white and turn off, linking is complete

10. To test if they’ve been successfully linked, press each switch to confirm that they control the light
    Now you’re ready to pair your switches with the Deako App

Troubleshooting

• Linking is only required for 3-way and 4-way wiring configurations
•  If at any point a switch blinks red, factory reset it and try again
• To exit linking mode at any point, press & hold the configure button for 10 seconds to factory reset each switch before retrying
• If you have dead-end or other nontraditional wiring in your home, you can find wiring and setup instructions at deako.com/wiring

Factory reset

Press & hold the configure button for 10 seconds (the LED will be appear solid red).

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF warning:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

IC Statement

– English: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licenceexempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation of the device.

The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B)
This device must be installed and operated with a minimum distance of 20 cm between the radiator and user body.
support.deako.com
1-844-673-3256

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>