EZVIZ CSC1HC1E2 Smart Home Camera User Manual

EZVIZ CSC1HC1E2 Smart Home Camera

Box Content

CAUTION
The camera appearance is subject to the actual one you have bought.

Basics

Name

• LED Indicator

Description

• Solid Red: Camera is starting up.
• Slow-flashing Red: Wi-Fi connection has failed.
• Fast-flashing Red: Device exception (e.g. microSD card error).
• Solid Blue: Video is being viewed or played back in EZVIZ App.
• Fast-flashing Blue: Camera is ready for the Wi-Fi connection.
• Slow-flashing Blue: Camera is running properly.

Name

• microSD Card

Description

• microSD Card should be purchased separately.
• Initialize the card in the EZVIZ app before using it.

Name

• RESET Button

Description

• Hold down the RESET button for 5 seconds while the camera is running, the camera restarts and all parameters are reset to default.

Setup

Step 1 Power-on

Plug the power cable into the camera and to the power adapter and then into a power outlet, as shown in the figure below.

Step 2 Camera Setup

Create a user account

• Connect your mobile phone to Wi-Fi.
• Download and install the EZVIZ app by searching “EZVIZ” in App Store or Google PlayTM.
• Launch the app and register for an EZVIZ user account following the start-up wizard.

Add a camera to EZVIZ

• Log in the EZVIZ app.
• From the EZVIZ app Home screen, tap “+” on the upper-right hand corner to go to the scan QR code interface.
• Scan the QR Code on the bottom of the camera.
•  Follow the EZVIZ app wizard to finish Wi-Fi configuration.

CAUTION: Please make sure your phone is connected to the 2.4GHz Wi-Fi from the router for Wi-Fi configuration.

Installation

Step 1 Install the Metal Plate (Optional)

Pick a clean and flat surface and secure the metal plate to the desired position with the foam stickers or screws (not included).
CAUTION: There’s a magnet piece inside the camera. You can skip this step if the surface is made of metal.

Step 2 Install the Camera
Secure the camera magnetically to the metal plate or metal surface (see figure below).

Step 3 Complete Installation
Adjust the camera angle as required.

Appendix

Step 1 Install Memory Card
Insert a microSD card into the slot until a click.

Step 2 Initializing Memory Card

1. In the EZVIZ app, check the memory card status by tapping on the Storage Status in the Device Settings interface.
   

2. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal.

NOTE; For detailed information, please visit www.ezvizlife.com

Regulatory Information

This product and – if applicable – the supplied accessories too are marked with “CE” and comply therefore with the applicable harmonized European standards listed under the Radio Equipment Directive
2014/53/EU, the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info

2006/66/EC and its amendment 2013/56/EU (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info

EC DECLARATION OF CONFORMITY
Hereby, Hangzhou EZVIZ Software Co., Ltd. declares that the radio equipment type [CS-C1C, CS-C1HC, CS-C1T, CS-C2C, CS-CV206, CS-CV310, CS-C3N, CS-C3W, CS- C3WN, CS-C3X, CS-C6N, CS-CV246, CS-CV248, CS-C6CN, CS-C6C, CS-C6W, CS-TY1, CS- TY2, CS-TY3, CS-CV336, CS-DP1, CS-DP1C, CS-DP2C, CS-DB2C, CS-C4W, CS-C4C, CS- CV228, CS-C5W, CS-C5C, CS-C5HC, CS-C5X, CS-C5HX, CS-C8W, CS-C8C, CS-CP1, CS- C3A, CS-BC1, CS-BC1-B1, CS-BC1-B2, CS-BC1-B3, CS-BC1-B4, CS-BC1C, CS-W2H, CS- X5S-4W, CS-X5S-8W, CS-A1-32W, CS-T9-A, CS-T4-A] is in compliance with Directive 2014/53/EU. The full text of the EC DECLARATION OF CONFORMITY is available at the following web link:
http://www.ezvizlife.com/declaration-of-conformity
Use only power supplies listed in the Table.

05050EPCU/EPC(US),
CS-C2C/ CS-CV206/| ADS-5RH-06 05050EPB(UK),
CS-CV246/CS-C6N/  CS-C6CN/| ADS-5RH-06 05050EPG(EU),
CS-C6C/ CS-TY1/ CS-TY2/| ADS-5RH-06 05050EPSA(AU),
CS-TY3/ CS-W2D/ CS-A1-32W/| ADS-5RH-06 05050EPBR(BR),
CS-T9-A/ CS-BC1C/ CS-CP1| ADS-5RH-06 05050EPI(IN),
ADS-5MA-06A 05050GPK(KR)
Sichuan Jiuzhou Electronic Technology Co., Ltd| DYS05100CP-U, DYS05100CP-E
CS-CV248/ CS-C6W/ CS-C6Wi/| Shenzhen Honor Electronic Co Ltd| ADS-10LA-06 05010EPCU/EPC(US),
CS-CV336/ CS-DP1/ CS-DP1C/| ADS-10RH-06 05010EPB (UK),
CS-DP2C/ CS-C3A/ CS-BC1/| ADS-10RH-06 05010EPG(EU),
CS-CP1| ADS-10RH-06 05010EPSA(SA),
ADS-10RH-06 05010EPBR(BR),
ADS-10RH-06 05010EPI(IN),
ADS-12CG-06 05010EPC(JP)
Sichuan Jiuzhou Electronic Technology Co., Ltd| DYS05200CQ-U, DYS05200CQ-E
CS-CV310/ CS-C3N/ CS-C3W/| Shenzhen Honor Electronic Co Ltd| ADS-12FG-12N 12012EPCU(US),
CS-C3WN/ CS-C3X/ CS-SD1/| ADS-12FG-12N 12012EPB(UK),
CS-C4W/ CS-C4C/ CS-CV228/| ADS-12FG-12N 12012EPG(EU),
CS-C8W/ CS-C8C/ CS-W2H/| ADS-12FB-12 12012EPSA(AU),
CS-W3C-WD1200G/  CS-T8-B| ADS-12FG-12N 12012EPBR(BR),
ADS-12FG-12N 12012EPI(IN)
CS-X5S-4W/ CS-X5S-8W/| Moso Power Supply Technology Co. Ltd| MSA-C1500IC12.0 -18P-GB(UK),
CS-X5S-16H| MSA-C1500IC12.0-18P-DE,
MSA-C1500IC12.0-18P-AU(AU),
MSA-C1500IC12.0-18P-BR(BR),
ADS-25FSG-12 12018GPI(IN)

Important Safety Information

• Note: Please read the manual before using the device.
• Caution : Be sure to read these instructions before operating the equipment.
• Warning : To reduce the risk of personal injury due to overheating of the components, wait until the surface cools down before touching it.
• Warning : The separate earthing terminal must be permanently connected to earth.
• Warning : For SELV DC input: the DC power source shall comply with the Safety Extra-Low Voltage (SELV) requirements of IEC 60950-1.
• Caution : Do not block ventilation openings while the system is on, and keep at least 2 cm distance from ventilation openings and walls or other things which may block the openings.
• Warning : Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery that can result in an explosion.
• Warning: Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
• Warning : A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
• Warning : Dispose of used batteries according to the instructions.
• Warning : Replace only with the same or equivalent type recommended by the manufacturer.
• Caution : THE PRODUCT IS BUILT IN A REPLACEABLE BATTERY.
• Warning : Do not ingest battery, Chemical Burn Hazard.
• Caution : This product contains a coin/button cell battery. If the coin / button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
• Caution : Keep new and used batteries away from children.
• Caution : If the battery compartment does not close securely, stop using the product and keep it away from children. Caution: If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
• Caution : Risk of fire or explosion if the battery is replaced by an incorrect type.

FCC Information
Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.

FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1.  this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>