KLEIN TOOLS VDV512-101 Cable Tester Instructions

: June 6, 2024
: KLEIN TOOLS

VDV512-101 Cable Tester
Instructions Manual

1. Test Remote #1 (Red)	8. Remote Holder
2. Test Remote #2 (Blue)	9. F-Adapter
3. Test Remote #3 (Green)	10. TEST Button
4. Test Remote #4 (Black)	11. PASS LEDs
5. F-Connector	12. OPEN Fault LED
6. Battery Cap	13. SHORT Fault LED
7. 2x AAA Batteries (included)	14. Pocket Clip (Back)

NOTE: There are no user-serviceable parts inside the tester.

GENERAL SPECIFICATIONS

The Klein Tools Coax Explorer® 2 verifies the proper continuity of F-connector coaxial cables and maps their location. The color-coded push-on remotes allow for up to four cables to be tested and mapped, displaying cable status via LED indicators (PASS, OPEN, or SHORT) that also identify the cable/remote location.

Environment: Indoor
Operating Altitude: 10000 ft. (3000 m) maximum
Operating Temperature: 32° to 122°F (0° to 50°C)
Storage Temp: -4° to 140°F (-20° to 60°C)
Relative Humidity: 10% to 90% non-condensing
Dimensions (including remote holder): 5.7″ x 2.3″ x 1.1″ (145 x 32 x 29 mm)
Weight (including batteries): 4.8 oz. (136 g) Specifications are subject to change.

TESTING/MAPPING CABLES

NOTE: Not for use on powered circuits or outlets.

Connect a test remote 1, 2, 3, or 4 to one end of the cable or outlet to be tested. If necessary, use the included F-adapter 9 to connect the test remote to the cable. If mapping, install remaining remotes to additional locations.
Connect the opposite end of the cable or outlet to be tested to the F-connector 5 on the Coax Explorer® 2.
Press and hold the TEST button 10. If the cable is wired correctly, one of the four PASS LEDs 11 will light, also indicating the cable/remote location. If there is a problem with the cable, one of the FAULT LEDs (OPEN 12 or SHORT **13** ) will light.
Repeat steps 2 and 3 to test/map additional cables.

TESTING AN UNINSTALLED CABLE

Using the included F-adapter 9 , connect a test remote 1 to one end of the cable to be tested.
Connect the opposite end of the cable to be tested to the F-connector 5 on the Coax Explorer® 2.
Press and hold the TEST button 10. If the cable is wired correctly, the corresponding PASS LED 11 will light. If there is a problem with the cable, one of the FAULT LEDs (OPEN 12 or SHORT 13 ) will light.

REMOTE HOLDER/STORAGE

The test remotes conveniently snap into the remote holder 8 for storage. To store the included F-adapter 9 , push two remotes onto the adapter before snapping the remotes into the holder.
The remote holder snaps onto the body of the Coax Explorer ® 2 and may be removed if desired. Hold the tester in one hand and apply slight downward pressure to one side of the remote holder with the other hand to release it from the tester. To reattach, align the holder with the tester body and snap it back into place.

BATTERY REPLACEMENT (FIG. 1)

When the TEST button is pressed and no LEDs light, the batteries must be replaced.

Unscrew the battery cap 6.
Remove and recycle the two spent AAA batteries 7.
Install two new AAA batteries, with the positive (+) side facing into the tester as shown.
Screw the battery cap tightly back into place.

STORAGE

Remove the batteries when the tester is not in use for a prolonged period of time. Do not expose to high temperatures or humidity. After a period of storage in extreme conditions exceeding the limits mentioned in the GENERAL SPECIFICATIONS section, allow the tester to return to normal operating conditions before using.

FCC AND IC COMPLIANCE

See this product’s page at www.kleintools.com for FCC compliance information.
Canada ICES-003 (B) / NMB-003 (B)

WARRANTY

www.kleintools.com/warranty

DISPOSAL / RECYCLE

Do not place equipment and its accessories in the trash. Items must be properly disposed of in accordance with local regulations. Please see www.epa.gov/recycle for additional information.

CUSTOMER SERVICE

KLEIN TOOLS, INC.
450 Bond Street, Lincolnshire, IL 60069
customerservice@kleintools.com
1-800-553-4676
www.kleintools.com
BASED ON 1330430 Rev. 11/21 E

VDV512-110 Instructions

1. Test Remote #1 (Red)	5. Remote Holder
2. Test Remote #2 (Blue)	6. F-Adapter
3. Test Remote #3 (Green)	7. Coax Explorer® 2 Tester (not included)

4. Test Remote #4 (Black)

GENERAL SPECIFICATIONS

The Klein Tools Coax Explorer® 2 verifies the proper continuity of F-connector coaxial cables and maps their location. The color-coded push-on remotes allow for up to four cables to be tested and mapped, displaying cable status via LED indicators (PASS, OPEN, or SHORT) that also identify the cable/remote location.
NOTE: The Coax Explorer® 2 tester is required, and is not included with this kit.

TESTING/MAPPING CABLES

NOTE: Not for use on powered circuits or outlets.

Connect a test remote 1, 2, 3, or 4 to one end of the cable or outlet to be tested. If necessary, use the included F-adapter 9 to connect the test remote to the cable. If mapping, install remaining remotes to additional locations.
Connect the opposite end of the cable or outlet to be tested to the F-connector 5 on the Coax Explorer® 2.
Press and hold the TEST button 10. If the cable is wired correctly, one of the four PASS LEDs 11 will light, also indicating the cable/remote location. If there is a problem with the cable, one of the FAULT LEDs (OPEN 12 or SHORT **13** ) will light.
Repeat steps 2 and 3 to test/map additional cables.

TESTING AN UNINSTALLED CABLE

Using the included F-adapter 6 , connect a test remote 1 to one end of the cable to be tested.
Connect the opposite end of the cable to be tested to the F-connector 7 on the Coax Explorer® 2.
Press and hold the TEST button. If the cable is wired correctly, the corresponding PASS LED 11 will light. If there is a problem with the cable, one of the FAULT LEDs (OPEN or SHORT) will light.

REMOTE HOLDER/STORAGE

The test remotes conveniently snap into the remote holder 5 for storage. To store the included F-adapter 6 , push two remotes onto the adapter before snapping the remotes into the holder.
The remote holder snaps onto the body of the Coax Explorer ® 2 7 and maybe removed if desired. Hold the tester in one hand and apply slight downward pressure to one side of the remote holder with the other hand to release it from the tester. To reattach, align the holder with the tester body and snap it back into place.

FCC AND IC COMPLIANCE

See this product’s page at www.kleintools.com for FCC compliance information.
Canada ICES-003 (B) / NMB-003 (B)

WARRANTY

www.kleintools.com/warranty

DISPOSAL / RECYCLE

Do not place equipment and its accessories in the trash. Items must be properly disposed of in accordance with local regulations. Please see www.epa.gov/recycle for additional information.