GO MOTO Premium Chin Mount User Manual
- October 27, 2023
- GO MOTO
Table of Contents
GO MOTO CHIN MOUNT
USER MANUAL
Premium Chin Mount
The Basics
Step 1: Find the right spot!
Before mounting the Go Moto mount to your helmet we strongly advice finding
the right spot on your helmet!
Use the product photos on our website of your chin mount to find the correct
placement on the helmet.
Do so without removing the 3M protective film. Move the mount untill all sides
line up with your helmet.
Remember the right spot!
Step 2: Clean mounting surface
Clean the mounting surface on your helmet with the provided 3M VHB Surface Cleaner. After cleaning the surface, wait a minute to let it dry.
Step 3: Prepare for mounting!
Peel off the protective film from the 3M VHB adhesive. We recommend warming up the 3M VHB adhesive (NOT HOT!) with a hair dryer for better adhesion.
Carefully line up the mount with your helmet (remember step 1). Don’t press
untill you have the placement just right. When you think the mount is on the
right spot, press hard and hold for at least 1 minute with firm pressure.
Potential gaps may be present between the 3M adhesive and the helmet. This
could be due to misplacement or not applying enough pressure. You can warm up
and press the chin mount again, or use something like a credit card to press
the 3M adhesive against the helmet to remove the gaps.
Step 5: Waiting…
You mounted your Go Moto mount?!
Well done!
Just a little patience…
Before using your Go Moto Mount, we recommend not using it for at least 24
hours to let the adhesive properly cure. The optimal waiting time for the 3M
VHB adhesive to settle is 72 hours.
We’d love to see your results! Share your Go Moto mount on Instagram or
Facebook with gomotomounts!
Questions?
Need any help mounting your Go Moto mount, or do you have any other
questions?
We’ll be happy helping you out!
Send an e-mail to: support@go-moto.com
Find Go Moto online!
www.go-moto.com
gomotomounts
****www.facebook.com/gomotomounts
Mounting action camera
You can mount an action camera mount by using a compatible mounting buckle.
This will be universal for different brands including: GoPro Hero/Session,
Insta360 ONE R, DJI Osmo Action, Xiaomi Yi 4K and more.
Push the buckle into place until it clicks.
Recommendation:
You can use an extenion arm for better adjustability of the camera angle.
Removing the mount.
Step 1: Weakening the adhesive
Removing the mount from your helmet can be pretty hard. Use the following
instructions so you won’t damage your helmet or the Go Moto mount:
We advice heating up the sides with a hair dryer to make the proces a little
easier. We also advise using something like an old credit card to remove the
mount. Push the credit card between the mount and the adhesive (so you won’t
scratch your helmet).
Push a credit card between the corners of the VHB adhesive untill it starts
coming loose at each corner.
Step 2: Twisting
When the corners of the adhesive are released, try twisting the Go Moto mount
(you can attach something to the mount to get more grip). For this step you
can also heat op the mount a little more. By twisting the Go Moto mount it
should release from your helmet. (Don’t pull! This may damage your helmet!)
WARNING:
Only use the correct Go Moto mount for the intended helmet. Always clean
your helmet with original 3M VHB surface cleaner before mounting the Go Moto
mount. The 3M VHB adhesive may not stick properly without using the 3M VHB
cleaner.
Only use original 3M VHB 4991 F adhesive for the Go Moto mount. Any other
adhesives may fail to hold.
Always check your action camera is properly mounted before riding.
Go Moto is not responsible for any damage caused by improper installation.
DANGER. 3M VHB surface cleaner:
Contains: Propan-2-ol.
Highly flammable liquid and vapour. Causes serious eye irritation. May cause
drowsiness or dizziness.
Keep away from heat, hot surfaces, sparks, open flames and other ignition
sources. No smoking. Avoid breathing vapours.
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact
lenses, if present and easy to do. Continue rinsing.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>