GRAM KSI 401754/1 Built In Fridge User Manual

BUILT-IN FRIDGE
User manual
KSI 401754/1

BEFORE USING THE APPLIANCE

General warnings
WARNING: Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.
WARNING: Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
WARNING: Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer
**WARNING: Do not damage the refrigerant circuit.
WARNING: In order to avoid any hazards resulting from the instability of the appliance, it must be fixed in accordance with the following instructions:
WARNING: When positioning the appliance, ensure the supply cord is not trapped or damaged.
WARNING:** Do not locate multiple portable socket outlets or portable power supplies at the rear of the appliance.

**** If your appliance uses R600a as a refrigerant (this information will be provided on the label of the cooler)you should take care during transportation and installation to prevent the cooler elements from being damaged. R600a is an environmentally friendly and natural gas, but it is explosive. In the event of a leak due to damage to the cooler elements,  move your fridge away from open flames or heat sources and ventilate the room where the appliance is located for a few minutes.

• While carrying and positioning the fridge, do not damage the cooler gas circuit.

• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

• This appliance is intended to be used in household and domestic applications such as:
  – staff kitchen areas in shops, offices, and other working environments which can be equated with ordinary household
  – farmhouses and by clients in hotels, motels, and other residential type environments which can be equated with ordinary household
  – bed and breakfast type environments which can be equated with ordinary household
  – catering and similar non-retail applications which can be equated with ordinary households.

• The appliance is supplied with a plug approved in the EU, which must not be used in a Danish installation, as the unit thereby is not earthed acc. Local regulations. Replacing the Danish plug must be performed by a qualified electrician. Alternatively, use an adapter to transition between the Schuko plug and the Danish earth system.

• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• Børn fra 3 til 8 år må lægge varer i og tage varer ud af køleapparater. Børn forventes ikke at udføre rengøring eller vedligeholdelse af apparatet. Meget små børn (0-3 år)  forventes ikke at bruge apparater. Mindre børn (3-8 år) forventes ikke at kunne bruge apparater på sikker vis, medmindre det sker under  supervision. Større børn (8-14 år)  og sårbare personer kan bruge apparater sikkert, når de superviseres og har fået den nødvendige vejledning i brugen af apparatet. Meget sårbare personer forventes ikke at bruge apparater på sikker vis, medmindre det sker under supervision.

• If the supply cord is damaged, it must be replaced by the manufacturer, an authorized service agent, or similarly qualified persons, in order to avoid a hazard.

• This appliance is not intended for use at altitudes exceeding 2000 m.

To avoid contamination of food, please respect the following instructions:

• Opening the door for long periods can cause a significant increase in the temperature in the compartments of the appliance.
• Clean regularly surfaces that can come in contact with food and accessible drainage systems
• Store raw meat and fish in suitable containers in the refrigerator, so that it is not in contact with or drip onto other food.

BEFORE USING THE APPLIANCE

Old and out-of-order fridges or freezers

• If your old fridge has a lock, break or remove the lock before discarding it, because children may get trapped inside it and may cause an accident.
• Old fridges and freezers may contain isolation material and refrigerant with CFC or HFC. Therefore, take care not to harm the environment when you are discarding your old fridges.

Please ask your municipal authority about the disposal of the WEEE reuse, recycling, and recovery purposes.

Notes:

• Please read the instruction manual carefully before installing and using your appliance. We are not responsible for the damage that occurred due to misuse.

• Follow all instructions on your appliance and instruction manual, and keep this manual in a safe place to resolve the problems that may occur in the future.

• This appliance is produced to be used in homes and it can only be used in domestic environments and for specified purposes.
  It is not suitable for commercial or common use. Such use will cause the guarantee of the appliance to be canceled and our company will not be responsible for losses incurred.

• This appliance is produced to be used in houses and it is only suitable for cooling / storing food. It is not suitable for commercial or common use and/or for storing substances except for food.
  Our company is not responsible for losses to be incurred on the contrary case.

| |
---|---|---

Safety warnings

• Do not use multiple receptacles or extension cords.
• Do not plug in damaged, torn, or old plugs.
• Do not pull, bend or damage the cord.
• This appliance is designed for use by adults, do not allow children to play with the appliance or let them hang over the door.
• Do not plug in or out the plug from the receptacle with wet hands to prevent electrocution!
• Do not place explosive or flammable material in your fridge for your safety. Place drinks with higher alcohol amounts vertically and by closing their necks tightly in the fridge.
• Do not cover the body or top of the fridge with lace. This affects the performance of your fridge.
• Fix the accessories in the fridge during transportation to prevent damage to accessories.

Installing and operating your fridge

Before starting to use your fridge, you should pay attention to the following points:

• The operating voltage for your fridge is 220-240 V at 50Hz.
• We do not take responsibility for the damages that occur due to ungrounded usage.
• Place your fridge in a place that it would not be exposed to direct
• Your appliance should be at least 50 cm away from stoves, Gas ovens, and heater cores, and should be at least 5 cm away from electrical ovens.
• Your fridge should never be used outdoors or left under the rain.
• When your fridge is placed next to a deep freezer, there should be at least 2 cm between them to prevent humidity on the outer
• Do not place heavy items on the appliance.
• Do not place anything on your fridge, and install your fridge in a suitable place so that at least 15 cm is available on the upper
• The adjustable front legs should be stabilized at an appropriate height to allow your fridge to operate in a stable and proper way. You can adjust the legs by turning them clockwise (or in the opposite direction). This should be done before placing food in the fridge.
• Before using your fridge, wipe all parts with warm water added with a teaspoonful of sodium bicarbonate, and then rinse with clean water and dry. Place all parts after cleaning.

Before using your fridge

• When it is operated for the first time or after transportation, keep your fridge in the upright position for 3 hours and plug it on to allow efficient operation. Otherwise, you may damage the
• Your fridge may have a smell when it is operated for the first time; the smell will fade away when your fridge starts to cool.

THE PARTS OF THE APPLIANCE AND THE COMPARTMENTS

This presentation is only for information about the parts of the appliance. Parts may vary according to the appliance model.

1. Control panel
2. Turbofan
3. Wine rack
4. Fridge shelves
5. Upper crisper cover
6. Upper crisper
7. Bottom crisper cover| 8. Bottom crisper
9. Bottle shelf
10. Door shelf (Adjustable door shelf )
11. Door shelf
12. Egg holder
13. Upper side LED strip
14. Left / Right side LED strip *

• In some models
  ---|---

General notes:
Fresh Food Compartment (Fridge): Most efficient use of energy is ensured in the configuration with the drawers in the bottom part of the appliance, and shelves evenly distributed, position of door bins does not affect energy consumption.

Dimensions

USAGE INFORMATION

Display and Control Panels

Using the Control Panel

1. Alarm indicator
2. Cooler set value screen.
3. Super Cool mode indicator
4. It enables the setting value of the cooler to be modified and super cool mode to be activated if desired. The cooler may be set to 8, 6, 5, 4, 2 °C, super cool.
5. It enables the economy mode to be activated if desired.
6. Eco mode indicator

Operating Your Fridge

If your product has lighting
When the product is plugged in for the first time, the interior lights may turn 1 minute late due to opening tests.
Super Cool Mode
How Would It Be Used?

Press the cooler set button (#4 on the control panel diagram) until the Super cool symbol (#3) will be seen on the screen. The buzzer will sound beep beep. The mode will be set.

During This Mode:

• An economy mode can not be selected.
• The super cool mode can be canceled by the same operation of selecting.

Economy Mode

How Would It Be Used?

• Push the “MODE” button (#5 on the control panel diagram) until the eco symbol appears.
• If no button is pressed for 1 second. The mode will be set. Eco symbol (#6) will blink 3 times. When the mode is set, the buzzer will sound beep beep.
• Cooler temperature segments (#2) will show “E”.
• Economy symbol and E will light till mode finishes.

During This Mode:

• The cooler may be adjusted. When economy mode will be canceled, the selected setting values will proceed.
• The super cool mode can be selected. Economy mode is automatically canceled and the selected mode is activated.
• To cancel, you will just need to press the mode button.

Screen Saver Mode
Purpose
This mode saves energy by switching off all control panel lighting when the panel is left inactive.

How to Use

• Screen saver mode will be activated automatically after 30 seconds.
• If you press any key while the lighting of the control panel is off, the current machine settings will reappear on the display to let you make any change you wish.
• If you do not cancel the screen saving mode or press any key for 30 seconds, the control panel will remain off.

To deactivate the screen saving mode,

• To cancel the screen saving mode, first of all, you need to press any key to activate the keys and then press and hold the Mode button “ ” (#5) for 3 seconds.
• To reactivate screen saving mode, press and hold the mode button “ ” (#5) for 3 seconds.

Door Open Alarm Function
If a cooler door is opened more than 2 minutes, the appliance sounds ‘beep beep’.
Temperature Settings
Cooler Temperature Settings

• The initial temperature value for the cooler setting indicator is +4 °C.

• Press the cooler button once (#4 on control panel diagram).

• When you first push this button, the last value will appear on the cooler setting indicator (#2).

• Whenever you press this button (#4), a lower temperature will be set. (+8°C, +6°C, +5°C, +4°C, +2°C, super cool)

• When you push the cooler set button until the super cool symbol (#3) appears, and if you do not push any button within 1 second, super cool will flash.

• If you continue to press the button(#4), it will restart from +8°C.

• The temperature value selected before super cool mode or economy mode is activated and will remain the same when the mode is over or canceled. The appliance continues to operate with this temperature value.

Recommended Temperature Values for Cooler

Warnings About Temperature Adjustments

• Do not pass to another adjustment before completing an adjustment.
• Temperature adjustments should be made according to the frequency of door openings, the quantity of food kept inside the fridge, and the ambient temperature of the place of your fridge.
• Your fridge should be operated up to 24 hours according to the ambient temperature without interruption after being plugged in to be completely cooled.
• Do not open the doors of your fridge frequently and do not place much food inside it in this period.
• A 5-minute delaying function is applied to prevent damage to the compressor of your fridge, when you take the plug off and then plug it on again to operate it or when an energy breakdown occurs. Your fridge will start to operate normally after 5 minutes.
• Your fridge is designed to operate in the ambient temperature intervals stated in the standards, according to the climate class stated in the information label. We do not recommend operating your fridge out of stated temperatures value limits in terms of cooling effectiveness.
• This appliance is designed for use at an ambient temperature within the 10°C – 38°C range.

Climate class and meaning:
T (tropical): This refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 43 °C.
ST (subtropical): This refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 38 °C.
N (temperate): This refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 32 °C.
SN (extended temperate): This refrigerating appliance is intended to be used at ambient temperatures ranging from 10 °C to 32 °C.

Accessories

Fresh dial
When the humidity controller is in the closed position, it allows fresh fruit and vegetables to be stored longer.
In case the crisper is totally full, the fresh dial is located in front of the crisper, should be opened. By means of this, the air in the crisper and humidity rate will be controlled and endurance life will be increased.
If you see any condensation on the glass shelf, humidity control should be taken into the open positions.

Visual and text descriptions on the accessories section may vary according to the model of your appliance.

ARRANGING FOOD IN THE APPLIANCE

• To reduce humidity and consequent increase of frost never place liquids in unsealed containers in the refrigerator. Frost tends to concentrate in the coldest parts of the evaporator and in time will require more frequent

• Never place warm food in the refrigerator. Warm food should be allowed to cool at room temperature and should be arranged to ensure adequate air circulation in the refrigerator.

• Nothing should touch on the back wall as it will cause frost and the packages
  can stick on the back wall. Do not open the refrigerator door too frequently.

• Arrange the meat and cleaned fish (wrapped in packages or sheets of plastic) which you will use in 1-2 days, in the bottom section of the refrigerator (that is above the crisper) as this is the coldest section and will ensure the best-storing conditions.

• You can put the fruits and vegetables into a crisper without packing.

• For normal working conditions, it will be sufficient to adjust the temperature setting of your refrigerator to +4 °C.

• The temperature of the fridge compartment should be in the range of 0-8 °C, fresh foods below 0 °C are iced, and rotted bacterial load increases above 8 °C and spoils.

• Do not put hot food in the refrigerator immediately, wait for the temperature to pass outside. Hot foods increase the degree of your refrigerator and cause food poisoning and unnecessary spoiling of the food.

• Meat, fish, etc. should be stored in the chiller compartment of the food, and the vegetable compartment is preferred for vegetables. (if available)

• To prevent cross-contamination, meat products, and fruit vegetables are not stored together.

• Foods should be placed in the refrigerator in closed containers or covered to prevent moisture and odors.

CLEANING AND MAINTENANCE

• Disconnect the unit from the power supply before cleaning.

• Do not clean the appliance by pouring water.

• Make sure that no water enters the lamp housing and other electrical components.

• The refrigerator should be cleaned periodically using a solution of bicarbonate of soda and lukewarm water.

• Clean the accessories separately with soap and water Do not clean them in the dishwasher.

• Do not use abrasive products, detergents, or soaps. After washing, rinse with clean water and dry carefully. When you have finished cleaning, reconnect the plug to the mains supply with dry hands.

• Clean the condenser with a broom at least twice a year. This will help you to save on energy costs and increase productivity.

THE POWER SUPPLY MUST BE DISCONNECTED.

Defrosting the Refrigerator Compartment

• Defrosting occurs automatically in the refrigerator compartment during operation; the water is collected by the evaporation tray and evaporates automatically.
• The evaporation tray and the water drain hole should be cleaned periodically with the defrost drain plug to prevent the water from collecting at the bottom of the refrigerator instead of flowing out.
• You can also clean the drain hole by pouring ½ glass of water down it.

Replacing the LED strip
1 or 2 led strips in the fridge are used to illuminate your appliance. Please call the serviceman.
Note: Numbers and location of led strips may be changed according to the model.
!!! Some versions may be without illumination.

SHIPMENT AND REPOSITIONING

Transportation and Changing of Installation Position

• The original packages and foamed polystyrene (PS) can be retained if required.
• During transportation, the appliance should be secured with a wide string or a strong rope. The instructions written on the corrugated box must be followed while transporting.
• Before transporting or changing the installation position, all the moving objects (ie, shelves, crisper…) should be taken out or fixed with bands in order to prevent them from getting damaged.
  Carry your fridge in the upright position.

BEFORE CALLING YOUR AFTER-SALES SERVICE

If your fridge is not working properly, it may be a minor problem, therefore check the following, before calling an electrician to save time and money.

prevents any damage to the compressor. This warning will off after the voltage gets to the required level.
•If the warning continues, please contact with authorized technical
service.
0.00E+00| “Refrigerator comp.
Not Cold enough”| The ideal temperature for Ref. The compartment is +4 °C. If you see this warning your foods have the risk of spoiling.
This warning becomes visible if electricity is off for a long time (most probably) or the refrigerator is activated for the first time or hot food is loaded to the appliance.| 1. Set the refrigerator temperature to colder values or set the super cooling
mode until the compartment gets to normal temperature.
2. Do not open the door much until this failure is off.
3. Please empty the location at the front area of the air duct channel holes.
4. Please be careful while loading the appliance in order not to avoid the ventilation at the areas which are very close to the sensor.
5. Please don’t open the refrigerator doors frequently until the warning disappears.
6. If the warning continues, please contact with
authorized technical service.
ERROR TYPE| MEANING| WHY| WHAT TO DO
---|---|---|---
Ell| Refrigerator comp. too Cold| The foods start to freeze because of the too much cold temperature.
This warning means that the temperature of the cooler compartment is very low. Therefore, this ambient condition may lead to the freezing of foods in the compartment.| 1. Check if the “Supercooling mode” is on.
2. Decrease the refrigerator temperature values.
3. If the warning continues, please contact authorized technical service.

What to do if your appliance does not operate;
Check that;

• There is no power,
• The general switch in your home is disconnected,
• The socket is not sufficient. To check this, plug in another appliance that you know which is working into the same socket.

What to do if your appliance performs poorly;
Check that;

• You have not overloaded the appliance,
• The fridge temperature is set to 2.
• The door is closed perfectly,
• There is no dust on the condenser,
• There is enough place at the rear and sidewalls.

If your fridge is operating too loudly; Normal Noises
Cracking (Ice cracking) Noise:

• During automatic defrosting.
• When the appliance is cooled or warmed (due to expansion of appliance material).
  Short cracking: Heard when the thermostat switches the compressor on/ off.
  Compressor noise: Normal motor noise. This noise means that the compressor operates normally Compressor may cause more noise for a short time when it is activated.
  Bubbling noise and splash: This noise is caused by the flow of the refrigerant in the tubes of the system.
  Water flow noise: Normal flow noise of water flowing to the evaporation container during defrosting. This noise can be heard during defrosting.
  Air Blow Noise: Normal fan noise. This noise can be heard in fridges during normal operation of the system due to the circulation of air.

If the edges of fridge cabinet that the door joint contact are warm;
Especially in summer (hot weather), the surfaces that the joint contact may get warmer during the operation of the compressor, this is normal.

If humidity builds up inside the fridge;

• Is all food packed properly? Are the containers dried before placing them in the fridge?
• Is the fridge door opened frequently? The humidity of the room gets in the fridge when the door is opened. Humidity build-up will be faster when you open the door more frequently, especially if the humidity of the room is high.

If the door is not opened and closed properly;

• Do the food packages prevent the closing of the door?
• Are the door compartments, shelves, and drawers placed properly?
• Are door joints broken or torn?
• Is your fridge on a level surface?

Recommendations

• To stop the appliance completely, unplug from the main socket (for cleaning and when the door is left open)

Tips for saving energy

1. Install the appliance in a cool, well-ventilated room, but not in direct sunlight and not near a heat source (radiator, cooker.. etc). Otherwise use an insulating
2. Allow warm food and drinks to cool down outside the appliance.
3. Cover drinks or other liquids when placing them in the appliance Otherwise humidity increases in the appliance. Therefore, the working time gets longer. Also covering drinks and other liquids helps to preserve smell and taste.
4. Try to avoid keeping the doors open for long periods or opening the doors too frequently as warm air will enter the cabinet and cause the compressor to switch on unnecessarily often.
5. Keep the covers of the different temperature compartments (crisper, chiller …etc ) closed
6. The door gasket must be clean and pliable. Replace gaskets if worn.

TECHNICAL DATA

The technical information is situated in the rating plate on the internal side of the appliance and on the energy label.
The QR code on the energy label supplied with the appliance provides a web link to the information related to the performance of the appliance in the EU EPREL database.
Keep the energy label for reference together with the user manual and all other documents provided with this appliance.
It is also possible to find the same information in EPREL using the link https://April.etc.Europa.EU and the model name and product number that you find on the rating plate of the appliance.
See the link www.theenergylabel.EU for detailed information about the energy label.

INFORMATION FOR TEST INSTITUTES

Appliance for any EcoDesign verification shall be compliant with EN 62552.
Ventilation requirements, recess dimensions, and minimum rear clearances shall be as stated in this User Manual. Please contact the manufacturer for any other further information, including loading plans.

CUSTOMER CARE AND SERVICE

Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the following data available: Model, Serial Number, and Service Index.
The information can be found on the rating plate. Subject to change without notice.
The original spare parts for some specific components are available for a minimum of 7 or 10 years, based on the type of component, from the placing on the market of the last unit of the model.

Visit our websites:
www.gram.dk
www.gram.no
www.gram.se
www.gram.fi

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>