NAILPOP NP100 Portable Nail Printer User Manual

NAILPOP NP100 Portable Nail Printer

Components

Cartridge (1EA)Paper (Medium 10EA)

NAIL POP Printer (1EA)| USB‒type C(1EA)
Alcohol prep pads (5EA)| Nail File(1EA)

Name for each component

• About the details about LED indicator, please check from the NAIL POP APP.

Quick Start Guide

STEP 1 Power on
Please press the power button about 3 seconds.

STEP 2 Connect to Bluetooth
To connect to Bluetooth, please search the printer on the setting of your smartphone. Ex) NailPOP XX:XX Please select the nail pop printer on the search list

STEP 3 App
Please choose a nail look design on the application

STEP 4 Printing
You can print out by pressing ‘Print’ button on the app after choosing a nail look design.

STEP 5 Attaching sticker
Please clean your nails by the prep pad enclosed in the cartridge box. And then, please attach the nail sticker printed on your nail and trim it by the nail file.

STEP 6 How to power off
Please press the power button about 3 seconds.

STEP 7 How to charge
You can charge the printer by USB type-C enclosed in the set. The red LED light is turned on during charging and the green LED light is turned on when the printer is charged.

How to put the cartridge

STEP 1 Please open the upper cover by pushing it to the left like the picture.

STEP 2 Please put the cartridge into the same direction on the picture.

Please don’t touch the paper and ribbon when putting the cartridge.

STEP 3 Please press ‘PUSH’ button on the cartridge.

STEP 4 Please press the hook of the cartridge until there’s clicked sound.

• When cartridge is put into correctly : White LED When cartridge is put into wrong : Red LED

How to pull out cartridge from the printer

STEP 1 Please press both sides of the hook of the cartridge.

STEP 2 Please pull out the cartridge while pressing the hook.

STEP 3 Please put the upper cover on the printer by pushing it to the right like the picture.

Specification

Battery 700mAh

| USB type USB C- type|

Bluetooth

---|---|---

Transferring nail design to the smartphone

Mobile Application

Search Nail POP App by the QR code.

Precautions

Precautions on charging| Please use 5V-1A charger. Please use the suitable charger and cable with the correct voltage. If you charge the product with the unofficial cable and charger for a long time, the product can be damaged.
The manufacturer has no responsibility on the issue caused by the unofficial cable and charger.
---|---
General precautions| The sticker is printed by moving back and forth in the slot for 6 times.

• Please don’t touch the paper during printing.

• Please don’t pull out the paper during printing.

• Please don’t put something on slot for paper.

• Please use the newest app version fir the best printing quality.
  Please check the newest version of the app on the Google Play Store and Apple App store.

• The printer has an inner battery. Please charge it before using it.

• Please don’t disassemble or deform it.

• Please avoid too high temperature and humidity.

• Proper temperature: 5~40℃

Check points before complaints about failure

• Please check if the power button is turned on.
• Please check the color of LED light. (Red light: On charging / Green light: Charging finished)

The power is not turned on.|

•  Please check if the battery is charged
• Please connect the charger to the USB port.
• Please check if the charger operating well.
• Please check if the voltage on your state is matched with the product’s voltage.

The paper is jammed.|

• Please turn on printer again after turning it off. The paper is printed automatically.
• Please reset the printer by putting the reset hole by a sharp thing

*If you can’t solve the issue with the above solutions, please contact to  CS center(+82) 070-5117-4717).

Specification

• Model name: NP100
• Product name: NAILPOP
• Made in Vietnam
• Dimension: 39.5mm x 148mm x 101mm
• Rated voltage: 5V 1A
• Optimal temperature: 5~40º
• Optimal humidity: Under 70%

Contact Point

TEL : 070 – 5117 – 4717
Homepage : http://www.nailpop.biz/

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receivers connected.
• Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT NOTE : FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IC Information to User This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must acceptany interference, including interference that may cause undesired operation of the device.

Caution
THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>