Atd Tools 80211 10W Flood Light User Manual
- June 6, 2024
- Atd Tools
Table of Contents
Atd Tools 80211 10W Flood Light
Product Description
- Rechargeable 10W clamp flood light with 5W speaker
- Stepless dimming function provide 100~1000lumen
- Special COB light source with uniform distribution
- Digital display battery indicator to easy understand battery status and lumens
- 360 degree rotatable bracket design to provide different angle
- Strong built-in magnetic design on the bottom, easy to place anywhere you want
- Use 5V 3.5A fast charger to shorten the charging time, with USB-C charging port
Specifications
-
Charger Specification:
AC100-240V ~ 50 / 60Hz -
Charging Voltage/Current: Battery Specification:
5V 3.5A3.7V 4400mAh Li-ion -
Charging time:
Approximately 1.5 hours -
Operation time for highest level:
Approximately 1.5 hours -
Operation time for lowest level:
Approximately 20 hours -
Brightness for highest level:
Approximately 1000 lumen -
Brightness for lowest level:
Approximately 100 lumen -
Color temperature:
5300~6700K -
CRI :
≥70
Battery treatment/charging
- Please full charge before first use
- Please use the charger equipped with the lamp
- Please do not leave the lamp in charge over 24 hours
- Do not leave battery in full discharged condition
- Please recharge the work light at least once in every six months
Setting up Speaker Connectivity
- Press the setting buttonto switch on speaker and you can hear the tone.
- Scan for available devices, select the “BT Speaker “ once it appears and wait to hear the tone.
- To disconnect a device press the Setting button to switch off the spearkers.
- Note paired devices will automatically connect once the speackers are turned on.
Warning
- Read all the instructions before using the appliance
- Wear safety goggles (User and bystander)
- Avoid looking directly into the beam
- To reduce the risk of injury, close supervision is necessary when an appliance is used near children
- Do not use the lamp near open flames
- Do not dismantle, open or shred secondary cells or batteries
- Do not cover the lens during the operating to prevent against overheating
- Do not contaminate the lens with organic solvents
- Do not knock、extrude the device
- Do not expose cells or batteries to heat or fire. Avoid storage in direct sunlight
- In the event of a cell leaking, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice
- Do not remove a cell or battery from its original packaging until required for use
- Do not use any charger other than that specifically provided for use with the equipment
- Do not repair the device, any repair should be performed by repair center
FCC Warning
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
device complies with part 15 of the FCC Rules. Operation is subject to the
following two
conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation. Note: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment should be installed and operated with minimum distance 20cm
between the radiator& your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>