VOLT VAL-204X-LI-BBZ Low Voltage Landscape Lighting Instruction Manual

VOLT VAL-204X-LI-BBZ Low Voltage Landscape Lighting Instruction Manual

Important: Please Read Before Installation

1. This LED Floodlight uses the latest in solid state lighting technology for long life, low maintenance, and high efficiency.

2. An internal power-factor-corrected switch mode supply allows this fixture to be used from any nominal 100V-277V, 50/60Hz AC supply without any variation in light output.

3. Suitable for use in:

   • Ambient Temperatures of6W & 12W:
     -20~+45 °C (-4~+113°F)
     18W: -20~+25 °C (-4~+77°F)

   • Wet Locations

4. INSTALLATION OR ASSEMBLY INSTRUCTIONS

Note: Save these instructions for future reference

Important Safety Instructions

To avoid the risk of fire, explosion, or electric shock, this product should be installed, inspected, and maintained by a qualified electrician only, in accordance with all applicable electrical codes.

To avoid electric shock:

1. Be certain electrical power is OFF before and during installation and maintenance.
2. Luminary must be connected to a wiring system with an equipment-grounding conductor.

To avoid explosion:

1. Make sure the supply voltage is the same as the rated luminary voltage.
   • 6W
   • 12W
   • 18W
2.  Do not install where the marked operating temperatures exceed the ignition temperature of the hazardous atmosphere.
3. Do not operate in ambient temperatures above those indicated on the luminary.

For supply connections use wire rated for at least 90°C (194°F)

Warning: these luminary should ONLY be installed by a qualified electrician.

Package Contents

1. (1) Fixture
2. (1) Allen Wrench

Products Model

Model

| Input Voltage| Power Factor| Watt| Input Current
---|---|---|---|---
6W Spotlight| 100-277V| ≥0.95| 6W|

.1A

12W Spotlight

| 100-277V| ≥0.95| 12W| .12A
18W Spotlight| 100-277V| ≥0.95| 18W|

.18A

Product Dimensions

• 6W 120V Spot Light & 12W 120V Spot Light
  

• 18W 120V Spot Light
  

Install Stake and Conduit

Dig a hole in the ground for the conduit runs and the stake. Install the conduit. Slide the stabilizer grid onto the stake and secure with the screws. Place the stake over the conduit runs. Back fill against the mounting stake.

Remove Cap from Stake

Remove the cap from the stake by loosening the set screws.

Install Cap to Fixture

Thread the cap onto the fixture body and hand tighten until snug.

Wire Connection and Fixture Installation

Allow enough wire from the fixture for adjustment purposes. Connect the wires from the fixture to the 120 v supply wires. The white wire goes to the “Neutral” wire; the black wire goes to the “Live” wire; and the green wire goes to the “Ground” wire. Use a UL certified wire connector for each connection.

Adjust Lamp Direction

Loosen the set screw at the joint by using the Allen wrench and adjust the fixture body to the desired direction. When the desired direction is achieved, tighten the set screw until snug.

After installation, please

1. Double check whether the lighting fixture is firmly fixed.
2. Double check the wires are connected correctly.

At last, turn on the power and check if the lighting fixture is working properly.

Customer suppot

Help Hotline:
1-813-978-3700
Mon-Fri 8am-8pm
Sat-Sun 10am – 6pm (EST)

www.voltlighting.com
Specifications and product details subject to change without notice.
© Copyright 2021, VOLT® Lighting, Lutz FL USA 33549
All rights reserved.
customersupport@voltlighting.com
813.978.3700

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>