Midea MBF2733PC Bladeless Purifier User Manual
- June 6, 2024
- Midea
Table of Contents
Midea MBF2733PC Bladeless Purifier
READ THIS MANUAL
Thank you very much for choosing our products. Please read the instructions
before using the product. This manual contains important information about the
operation, care and service of the product. Keep it in a safe place for future
reference. If the product is sold or transferred to another person, or you
move and leave the appliance, always be sure to leave the instruction manual
with the appliance so that the new owner is familiar with the appliance’s
operation and the relevant warnings.
We have included some important safety messages in this manual and on your
appliance. Always read and obey all safety messages.
This is the safety warning symbol. This symbol calls attention to death to potential hazards that may or may only cause injury to you and others. All safety messages will follow the safety warning symbol and the word “DANGER” or “WARNING”. These words mean: If you don’t follow instructions right away, you could be killed or seriously injured. If you don’t follow instructions, you could be killed or seriously injured.
All safety messages will tell you about the potential danger, how to reduce the chances of injury, and what can happen if instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
DANGER
Read Rules for Safe Operation and Instructions Carefully.
WARNING
-
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
-
WARNING—To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.
-
This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded or returned to an authorized service facility for exami- nation and/or repair.
“Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.”
“Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.” -
Do not leave the fan running unattended.
-
Keep electrical appliances out of reach from children or infirm persons. Do not let them use the appliances without supervision.
-
If the supply cord is damaged, it must be replaced by manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
-
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
-
When the fan was assembled, the rotor blade guard shall not be taken off anymore.
-
Prior cleaning unplug the fan.
-
The rotor guard shall not be dissembled/opened to clean the rotor blades.
-
Wipe the fan enclosure and rotor blade guard with a slightly damp cloth.
RULES FOR SAFETY OPERATION
- Never insert fingers, pencils, or any other object through the grille when fan is running.
- Disconnect fan when moving from one location to another.
- Be sure fan is on a stable surface when operating to avoid overturning.
- DO NOT use fan in window, rain may create electrical hazard.
- Household use only.
PRODUCT INTRODUCTION
NOTE : Pictures in the manual are for reference only, and real objects
within the packaging box will prevail in the end.
Parts Name
| NO. | Description | NO. | Description |
|---|---|---|---|
| 1 | Operation panel | 6 | Power line |
| 2 | Display panel | 7 | Power cord plug |
| 3 | Air outlet | 8 | Air inlet grille |
| 4 | Ambient light of belt | 9 | Pre-filter |
| 5 | Base | 10 | HEPA filter |
Parts List
INSTALLATION INSTRUCTIONS
Remove the air inlet grille.
Take out the pre-filter Press the raised part on both sides to pull it outwards, and take out the pre-filter.
Remove the protective film of the filter.
Install the HEPA filter
Install
the pre-filter Align the slot position at the bottom, and buckle up the upper
U-shaped buckle.
Install the air inlet grille Align the upper two buckles and press them tightly, then press the two sides at lower part, slowly and gently buckle the air inlet grille.
Plug power supply
It is recommended to clean the filter once every two weeks and replace it once every six months (the cleaning and replacement cycle can be adjusted according to the use environment).
CONTROL AREA
DISPLAY AREA
OPERATION
Additional Features and Maintenance
Forced shutdown
There is no operation during the running of the fan, after 12 hours of contin-
uous operation, the fan will be forced to shut down automatically.
Intelligent memory
When the fan is turned off or powered off, it will run in the state before
turning off or power off when the power is powered on again (the timing
function is not memorized).
Screen-off function
In case of no operation for 60 seconds during normal operation, the indicator
light on the body will be automatically off, but the fan will continue to
oper-ate. Press the ON/OFF button to turn off the fan when the screen is off,
and press the other button to restore display.
Automatic reset of oscillating function upon shutdown Upon shutdown, the oscillating function is automatically reset.
Remote Control Button Description
Note: The remote control should be normally used within 5 meters of the front of the product and 30 degrees of the deviation angle. The battery contains many heavy metals, acids and bases, etc., which may threaten human’s health; Waste batteries should be recycled separately.
OPERATION
Battery
Use manganese or alkaline batteries of type “AAA”. DO not use rechargeable
batteries.
Filter Replacement
Filter model: FQ150CJ-2 (including 2 sets)
When the indicator light for replacement of filter is on, the prompt that reminds you of filter replacement will appear. If it is not replaced in time, the prompt will appear during each startup.
Replace a new filter
Long press the button for 3 seconds to turn off the indicator light for filter replacement.
Pre-Filter Cleaning
Unplug the power cord
Take out the filter
Remove the dust with vacuum cleaner
Install the machine in reverse order and plug power supply
Product Parameter
| Model | Rated voltage | Rated frequency | Rated power | Noise |
|---|---|---|---|---|
| MBF2733PC | 120V~ | 60Hz | 33W | **** |
USER SERVICING INSTRUCTIONS
- Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
- Open fuse cover. Slide open fuse access cover on top of attachment plug towards blades.
- Remove fuse carefully. Insert the tip of your tool into fuse slot (close with the terminal), then prize the fuse gradually and slowly, but not overexert. If you feel tight, you can try it at several times and prize the fuse little by little. When one side of the fuse has been prized, then you can get the fuse out entirely.
- Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse.
- Close fuse cover. Slide closed the fuse access cover on top of attachment plug.
- Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged.
Notice:
1. When you replace the fuse, please don’t operate suddenly or overexert, or else the product will be damage or cause accident.
2. When you feel it hard to be operated, please make sure you have got the right way.
CLEANING
1. Be sure to unplug from the electrical supply source before cleaning.
2. Plastic parts should be cleaned with mild soap and a damp cloth or sponge.
Thoroughly to remove soap film with clean water.
3. Be sure not to make water or other liquid enter inside of the motor.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>