FIAMMA CF10202 Turbo Vent 40 Skylight Instruction Manual
- June 6, 2024
- FIAMMA
Table of Contents
FIAMMA CF10202 Turbo Vent 40 Skylight
Package contents
- Turbo-Vent White 03623F01- 03624F02-
- Turbo-Vent Crystal 03623F01B 03624F02D
| EN | ES |
|---|---|
| Nominal supply voltage | 12 V |
| Tension tolerance | +/- 30% |
| Min. feeding tension | 8 V |
| Maximum supply voltage. | 16 V |
| Power of nominal supply voltage | 36 W |
| Auto-resettable Fuse | __ |
| Current protection intervention | 5 A |
| Wire section | 17 AWG |
– 1 mm²
Min. electric input| 0,3 A +/-
10%
Max. electric input| 3,0 A +/-
10%
Operating tem- perature| -10°C /
+60°C
Storage temperature| -20°C /
+80°C
Check that nothing has been damaged or deformed during transport. In the event of doubts or questions concerning the installation, use or limitations of the product, contact the dealer. We recommend that the installation is carried out by qualifi ed personnel and in compliance with current local regulations.
Installation instructions
- Decide where the roofl ight should be installed and make a square hole of 39cm. The roofl ight can be installed on roofs with thickness between 30 and 85mm.
- Do not forget to arrange the electrical connection directly from the battery (only 12Vdc – NOT 220V).
- Seal the lower part of the external frame with a minimum width of 30 mm by following the appropriate rails. Recommended sealant: SIKALASTOMER-710 / THEROSTAT II / DEKALIN 1512.
- Place the external frame in the opening hole making sure that the hinges are facing the front of the vehicle.
- Fasten the external frame with 20 self tapping screws (Ø4.2x30mm UNI EN ISO 7049). Carefully siliconate all the perimeter of the external frame, fi ll any spaces between the roof and the frame and all the heads of the 20 screws.
- Before connecting the input cables, make sure that the speed control is in “OFF” position.
- Connect the input cables of the electric motor.
- Fasten the internal frame with 8 self tapping screws (Ø3.5x15mm UNI EN ISO 7049). Remove the protective plastic applied to the cover (do not expose the product to sunlight for too long to avoid to make this operation diffi cult).
Instructions for use
POLAR CONTROL
In this area the thermostat is active, the extremes indicating the intervention temperatures are stated. By switching the knob on a position in this area, the motor runs automatically identifi ng the set-up speed position and the direction (IN-OUT).
Ensure that the power supply has been disconnected before carrying out any kind of operation, then reconnect.
In case of problems please contact your local dealer indicating the data on the nameplate. Consult our website for spare parts
drawing .Fiamma declines all responsibility for any personal injury and damage to property due to incorrect assembly or use of the product; it is suggested to keep the instructions inside the vehicle. The assembly of the product must be carried out according to the assembly instructions: the product must not be modifi ed in any way. Before proceeding with assembly, check that the roof thickness is compatible with the product. Before choosing the place where to assembly the rooflight, check that:
CaRE AND MAINTENANCE:
For the internal and external cleaning of the roofl ight, always use only
neutral, non-aggressive detergents. For cleaning the Crystal cover use an
acrylic glass cleaner with a soft cloth so as not to scratch the surface.
Never use aggressive products such as glass cleaners, all-purpose cleaners,
abrasives or dish-washing detergents. Also, never use alcohol-containing
detergents, solvents or any corrosive liquid. The mosquito net can be cleaned
with water and a neutral detergent.
Accessories
y = – White; B/D = Crystal
The object of the declaration described above is in conformity with the
relevant Union harmonisation legislation:
- 2014/30/EU Electro Magnetic Compatibility Directive (EMCD).
- 2014/35/EU Low Voltage Directive (LVD).
- 2011/65/EU Restriction of the use of certain hazardous substances Directive (RoHS Directive).
- ECE/ONU/R10 Uniform provisions concerning the approval of vehicles with regard to electromagnetic compatibility – R10.
- ECE/ONU/R43 Uniform provisions concerning the approval of safety glazing materials and their installation on vehicles – R43 (only for Turbo 28, 28 F, Vent, Vent P3 and Vent Premium).
- EN 55014-1:2006 + A1:2009+ A2:2011 – RCM (only for Turbo 28, 28 F and Turbo Vent Premium).
- EN 61000-3-2:2014 – RCM (only for Turbo 28, 28 F and Turbo Vent Premium).
- EN 61000-3-3:2013 – RCM (only for Turbo 28, 28 F and Turbo Vent Premium).
- EN 55014-2:2015 – RCM (only for Turbo 28, 28 F and Turbo Vent Premium).
The following harmonised standards and/or technical specifications have been applied
Warranty Fiamma
In case of defects with regards to materials and manufacturing, the customer
is entitled to the warranty in accordance with local laws and regulations of
the country in which the product was purchased.
Fiamma S.p.A. – Italy
Via San Rocco, 56
21010 Cardano al Campo (VA)
All rights reserved.
Fiamma S.p.A.
reserves the right to modify at any time, without notice, prices, materials,
specifications and models or to cease production of any model.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>