ETEKCITY EK8060 Digital Kitchen Scale User Manual

ETEKCITY EK8060 Digital Kitchen Scale

Package Contents

• 1 x Digital Kitchen Scale
• 2 x 3V CR 2032 Batteries (Pre-Installed)
• 1 x Quick Start Guide

Specifications

Important Safety Information

To avoid damage to this scale, please read and follow all instructions and safety guidelines in this manual.

Scale

• Always place the scale on a hard, dry, and flat surface before measurement in order to ensure accuracy
• Do not exceed the 11 lb / 5000 g weight capacity as it will damage the An error indicator will appear on the LCD display if the limit is exceeded
• Do not immerse the scale in water or any If the liquid is spilled on the digital display or buttons, immediately wipe the scale dry with a soft cloth to avoid internal damage.
• Handle with This scale is not intended for commercial or heavy-duty use.
• Keep the scale in a cool, dry Avoid exposure to damp environments or extreme temperatures.
• Household use only.

Batteries

• Do not mix new and old
• If the low battery indicator “ “ appears on the display, replace the
• If the scale is not in use for an extended period of time, remove the batteries to conserve battery life and extend the lifetime of the

Function Diagram

• A. Unit Selection Button
• B. LCD Display
• C. Power/Tare Button
• D. Battery Compartment
• E. Screw
• F. Anti-Skid Pads

Symbols

Using Your Scale
Note:

• For accurate results, always place the scale on a hard, dry, flat surface, and keep the scale away from dirt, dust, vibrations, wind, air currents, and electromagnetic
• When you turn on the scale, choose units, or use the tare function, wait for the display to read before
• The batteries are pre-installed in the Turn the scale over and pull the plastic strip out from the battery compartment.

General Operation

• Place the scale on a hard, flat, level surface.
•  Press to turn on the scale. Make sure the display reads.
• Press UNIT to select your desired measuring unit, which will show on the right of the display.
• Place your item on the scale.
• Wait for the reading on the display to stabilize.

Zero / Tare Function

Whenever you measure items inside a container, you can use the tare function to remove the container’s weight from the final measurement.

• Press to turn on the scale. Make sure the display reads. If the screen does not display automatically, press TARE to auto-adjust to zero.
• Place the container on the center of the scale.
• Wait for the reading on the display to stabilize. The display will show the container’s weight.
• Press  to tare the weight of the container. The screen should now display.
• Place the liquid or items into the container. The scale will measure the contents without including the weight of the container. [Figure 2.1]
• When you’re done, reset the scale by removing all weight and pressing again

Unit Conversion
To change the unit of measurement, press UNIT until the display shows the desired unit of measurement.

Automatic Power Off
To save battery power, the scale will automatically power off after 180 seconds of inactivity.

Manual Power Off
Press and hold for 2 seconds to turn off the scale.

Replacing the Batteries

1. Turn the scale over and open the battery compartment.
2. Take out the used batteries and replace them with 2 new 3V CR 2032 batteries.
3. Replace the battery compartment cover and screw it shut.

Troubleshooting

Scale does not turn on.

| Open the battery compartment cover and remove the plastic strip.
Replace the batteries (see page 8).
Make sure batteries are inserted under the correct polarity as marked in the battery compartment.

Reading is inaccurate.

| Place scale on a level surface.
Make sure the screen displays before measuring (see Zero / Tare Function , page 7).
Remove the batteries for 45 seconds, then replace them to reset the scale.

Display shows

| Item is too heavy. Remove item from scale to protect its weight sensors. Use a different scale with a higher weight range.

Display shows

| Calibration error. Turn the scale off and on again. Avoid moving the scale while measuring.

Display shows

| Battery power is low. Replace the batteries (see page 8).

Warranty Information

For your own reference, we strongly recommend that you record your order ID and date of purchase.

Terms & Policy

Etekcity Corporation (“Etekcity”) warrants this product to the original purchaser to be free from defects in material and workmanship, under normal use and conditions, for a period of 2 years from the date of original purchase. Etekcity agrees, at our option during the warranty period, to repair any defect in material or workmanship or furnish an equal product in exchange without charge, subject to verification of the defect or malfunction and proof of the date of purchase.

There is no other express warranty. This warranty does not apply:

• If the product has been modified from its original condition;
• If the product has not been used in accordance with directions and instructions in the user manual;
• To damages or defects caused by accident, abuse, misuse, or improper or inadequate maintenance;
• To damages or defects caused by service or repair of the product performed by an unauthorized service provider or by anyone other than Etekcity;
• To damages or defects occurring during commercial use, rental use, or any use for which the product is not intended
• To damages or defects exceeding the cost of the

Etekcity will not be liable for indirect, incidental, or consequential damages in connection with the use of the product covered by this warranty. This warranty extends only to the original consumer purchaser of the product and is not transferable to any subsequent owner of the product regardless of whether the product is transferred during the specified term of the warranty. This warranty does not extend to products purchased from unauthorized sellers. Etekcity’s warranty extends only to products purchased from authorized sellers that are subject to Etekcity’s quality controls and have agreed to follow its quality controls. All implied warranties are limited to the period of this limited warranty. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. If you discover that your product is defective within the specified warranty period, please contact Customer Support via support@etekcity.com. DO NOT dispose of your product before contacting us.  Once our  Customer  Support Team has approved your request, please return the product with a copy of the invoice and order ID. Every Etekcity product automatically includes a 2-year warranty. To make the customer support process quick and easy, register your product online at www.etekcity.com/warranty.

This warranty is made by: Etekcity Corporation 1202 N. Miller St., Suite A Anaheim, CA 92806

Customer Support

If you have any questions or concerns about your new product, please contact our helpful Customer Support Team.

CUSTOMER SUPPORT

Etekcity Corporation
1202 N. Miller St., Suite A
Anaheim, CA 92806
Email : support@etekcity.com
Toll-Free: 855-686-3835

SUPPORT HOURS
Mon–Fri, 9:00 am–5:00 pm PST/PDT
*Please have your order invoice and order ID ready before contacting Customer Support

References

• Vesync-Warranty Registration

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>