MEGA LITE CV1 Deco Driver User Manual

MEGA LITE CV1 Deco Driver

Protection Against Fire

1.  Maintain a minimum of 1 foot distance from any type of flame.
2. Do Not install the unit too close to a heat source.
3. Make sure cables are properly secured away from movement.
4.  Maximum surface operating temperature is 135°F
5. Unit must not be left on for long periods of time.

Protection Against Electrical Dangers

1.  Disconnect power before servicing.
2. For connection to main power supply proceed to page 4.
3. This unit must be earthed. (electronically grounded)
4. Do not expose unit to rain or moisture.
5.  The Unit must be installed in a well ventilated area.
6. Be sure ventilation slots are not blocked.

Protection Against Mechanical Hazards

1. Unit surface may reach high temperature. Allow about 5 minutes after powering the unit before moving.
2. When positioning unit make sure it is securely mounted.
3.  Do not mount unit directly above any person.

What is Included
1pc Deco Driver CV1
1pc 5 Pin Screw Terminal Block 1pc 2 Pin Screw Terminal Block 1pc User Manual

Specifications

• Fastening System: Tear Drop Wall Mount
• Display: Digital
• Power Connection: Cable Mounted to Edison head.
• Housing: Black Painted
• DMX Connection: 5 Pin XLR & RJ45 in and out (optional 3 pin available)
• Output Connection: 5 pin Screw terminal & RJ45 output

Electrical Specifications

• Power Input: 110-240VAC 5.9A 50/60 Hz
• Output: 1
• Power Per Output 96W
• Wire Class: Class 2 Wiring
• Ballast: Electronic: Mean Well RD-125
• Output: 24V
• Drive Method: Constant Voltage
• Fuse: F2AL 250V (5X20mm)

Control & Programming

DMX 5 Modes:

1.  Channel Mode Dimmer
2. Channel Mode Warm White, Cool White
3.  Channel Mode R, G, B
4. Channel Mode R, G, B, W
5.  Channel Mode Dimmer R, G, B, W, Strobe, Macro
   Operating Mode: 21 Pre Programs, Stand alone via display

Main Power Connection

Caution!

1.  Do not connect fixture to a dimmer system.
2.  This unit has Auto switching power supply. It will respond to 110V or 220V automatically
3. This unit must be earthed. (electronically grounded)
4. Replace fuse only with the specified type and rating.

The occupation of the connection-cable is as follows:

This fixture is equipped with an electronic power supply that will let the unit operate from 100V to 240V from 50Hz to 60Hz

DMX-512 Connection

The fixture is equipped with 5 pin XLR Sockets and RJ45 for DMX input and output. The sockets are wired in parallel. Only use a shielded twisted pair cable designed for RS-485 and 5 pin XLR or RJ45 plugs and connectors in order to connect the controller with the driver or the driver with another.

12V Sensor By-pass

Once the Deco Drive CV1 receives a 12V input signal all dimmer channels will go to a full position and by pass DMX Control. Once 12V signal is removed the DMX Control will be reengaged to original settings

Output Connection

Deco Driver CV1 is designed to be used as a driver for Constant Voltage lighting fixtures. There are many fixtures a Deco Driver can control . The Deco Lighting fixture manual will give you the information with power link limitations and control type for that unit.
Important Information!

1.  Maximum Cable distance of 100ft before voltage drop. (voltage drop will cause intensity drop)

2.  All fixtures connected together must be same type (do not connect Multiple Color, Variable White or Single Color fixtures in the same output)
   

3. Must use Cat 6A, 24 AWG or thicker to connect the fixture and fixture to fixture. (not included)

Fixtures that require Strip Cable connection will connect the input cables via 5Pin Screw terminal. Use 20AWG cable or thicker for connections. Cables exceeding 100ft will have volt-age drop. Voltage drop will result in intensity drop.

Fixtures that require RJ45 connection will connect the input cables to RJ45 Output. Use Cat6 A AWG 24 or thicker cable for cable connection with RJ45 connections. Ca-bles exceeding 100ft will have voltage drop. Voltage drop will result in intensity drop.

Control Board

Lock Display: The display for the Deco Driver factory setting is lock screen function to unlock the display press and hold the Menu & Enter for 3 seconds. To relock press and hold the Menu & Enter for 3 seconds

DMX: DMX mode allows you to set the DMX operational mode and start channel. Press Enter use the Up / Down button to select your operating mode. Each lighting fixture will have a different operating mode. Consult the fixture’s manual or fixture label to determine the operating mode. Press Enter, DMX Address will then be highlighted, use the Up / Down button to select the fixtures start address. Start address should match your controller’s start address channel. Press Enter to confirm your settings.

Slave: This function allows the fixture to operate the same way as the master. Driver units must be connected via DMX cable

Auto: Auto mode allows you to access the pre-built auto function for control. Press Enter use the Up / Down button to select the pre pro-gram fixture look. Programs 01 to 18 are single scene programs and programs 19 to 21 are chase programs. Press Enter once you have decided on the scene or chase. For programs 19-21 use the Up/Down buttons to adjust the chase speed. Press Enter to confirm the fixture setting.

Manual: Manual mode allows you to man-ually control the intensity via the control display without the need for a DMX controller. Press Enter to select the dimmer output you would like to adjust . Use the Up/Down keys to select the dimmer intensity. There is many Deco Fixtures that can be controlled via a Deco Driver. Please Consult your Deco Lighting fixtures Manual to see what values are active. Press Enter to con-firm the setting. (Note for Variable White fixtures the R with correspond to Warm White and the B will correspond to Cool White all other dimmers must be off.)

DMX Profile

Deco CV1 1 Channel Mode

Deco CV1 2 Channel Mode

Deco CV1 3 Channel Mode

Deco CV1 7 Channel Mode

6

|

Strobe

| No Function| 0-1|

0

Strobe (slow to fast)| 2-127
Random Strobe (slow to fast)| 128-255

7

|

Macro

| No Function| 0-1|

0

Color Fade (slow to fast)| 2-127
Color Chase (slow to fast)| 128-255

Size & Weight

Cleaning and Maintenance

Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installations and electronics checked by an expert every 2 years.
The following points have to be considered during the inspection:

1. All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2. There must not be any deformations on the housing, fixation and installation spots (rack, suspension, trussing).
3. The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments. Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed.
4. Ventilation ports must be clear of any debris.
5. Inner ventilation power supply fan must be clear of any debris

Rigging the Fixture

Caution!

1. The installation must be carried out by an authorized dealer or trained professional.
2. Unit may cause severe injures if you have doubts concerning the safety do not install.
3. Unit is to be 24inches away from flammable materials (decoration material)
4. Installation location must have adequate air flow.

When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experi-ence including but not limited to calculating working loads, material being used and periodic safety inspections. If you lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger. When rigging the unit always be secured with a secondary safety attachment. The installation location of the Fixture has got to be built in the way that it can hold 10 times the weight for 1 hour without any failures. Installation should be checked at least one time a year by a skilled person.

Parts List

Customer Support

Mega Lite has a customer support line to provide set up help and to answer any question should you encounter a prob-lem. Please visit our website for any other related technical documents. For service related issue please contact our service dept.
Monday—Friday 9am to 6pm CST
Voice: 210-684-2600
E-mail: service@mega.lighting
Manual Version
Please Visit www.mega.lighting for the most up to date manual version

Document

Version

| Date| Fixture Software| Notes
---|---|---|---
1.1| 06/01/2021| V1.1|

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>