ELATEC TWN4 Multitech 3 Legic M LF HF Instruction Manual
- June 6, 2024
- ELATEC
Table of Contents
ELATEC TWN4 Multitech 3 Legic M LF HF
INTRODUCTION
ABOUT THIS MANUAL
This integration manual explains how to integrate ELATEC RFID reader module
TWN4 MultiTech 3 LEGIC M LF HF into a host device and is mainly intended for
integrators and host manufacturers.
The content of this integration manual is subject to changes without prior
notice and printed versions might be obsolete. Integrators and host
manufacturers are required to use the latest version of this integration
manual.
For the sake of better understanding and readability, this manual might
contain exemplary pictures, drawings and other illustrations. Depending on
your product configuration, these pictures might differ from the actual design
of your product.
ABOUT TWN4 MULTITECH 3 LEGIC M LF HF
TWN4 MultiTech 3 LEGIC M LF HF integrates RFID (125 kHz and 13.56 MHz) and NFC capabilities into a compact but powerful reader. Its reduced size combined with optimized read/write performance makes it the perfect reader for all applications where small size and full performance matters, e.g. print solutions, healthcare applications, driver identification, POS integration and much more. Furthermore, TWN4 MultiTech 3 LEGIC M LF HF provides access to most common host interfaces, such as USB, serial (TTL) or I2C, which are readily accessible through an on-board connector.
ELATEC SUPPORT
In case of any technical questions, refer to the ELATEC website
(www.elatec.com) or contact ELATEC technical support at:
support-rfid@elatec.com
SAFETY INFORMATION
- ELASTIC TWN4 MultiTech 3 LEGIC M LF HF is an electronic component and should be installed exclusively by a trained and qualified personnel.
- ELASTIC recommends the integrators to follow general ESD protective measures during the installation of TWN4 MultiTech 3 LEGIC M LF HF into a host device, e.g. the use of an antistatic wristband or special gloves.
- The integrator should not touch the antennas (if not shielded), printed circuit boards, connectors or other sensitive components on TWN4 MultiTech 3 LEGIC M LF HF.
- Before installing TWN4 MultiTech 3 LEGIC M LF HF into a host device, the integrator should also make sure that he/she has read and understood the ELATEC technical documentation related to TWN4 MultiTech 3 LEGIC M LF HF, as well as the technical documentation related to the host device. In particular, the instructions and safety information given in the user manual of TWN4 MultiTech 3 LEGIC M LF HF should be read carefully and listed in the technical documentation of the host manufacturer as well, as soon as these instructions and safety information are required for a safe and proper use of the host device containing TWN4 MultiTech 3 LEGIC M LF HF.
INTEGRATION INSTRUCTIONS
GE NERAL
TWN4 MultiTech 3 LEGIC M LF HF may be installed in any host devices, as long as it is operated under the operational conditions stated in the user manual and other technical documents (e.g. data sheet). TWN4 MultiTech 3 LEGIC M LF HF is equipped with two integrated antennas. Thus, no antenna installation is required.
LIST OF APPLICABLE RULES
Refer to the approval certificates, grants and declarations of conformity
issued for TWN4 MultiTech 3 LEGIC M LF HF, and to Chapter “Compliance
Statements” for a detailed list of the rules applicable to TWN4 MultiTech 3
LEGIC M LF HF.
SPECIFIC OPERATIONAL USE CONDITIONS
There are no specific operational use conditions for TWN4 MultiTech 3 LEGIC
M LF HF other than the conditions mentioned in the user manual and data sheet
of TWN4 MultiTech 3 LEGIC M LF HF. The host manufacturer or integrator must
ensure that these use conditions comply with the use conditions of the host
device. In addition, these use conditions must be stated in the user manual of
the host device.
LIMITED MODULE PROCEDURES
n/a
TRACE ANTENNA DESIGN
n/a
RF EXPOSURE CONSIDERATIONS
The module antenna(s) must be installed to meet the RF exposure compliance
separation distance of 0 cm and any additional testing and authorization
process as required.
Refer to Chapter “Compliance Statements” for detailed information about the
radio frequency exposure conditions applicable to TWN4 MultiTech 3 LEGIC M LF
HF.
These RF exposure conditions must be stated in the end-product manual(s) of
the host product manufacturer.
ANTENNAS
TWN4 MultiTech 3 LEGIC M LF HF is equipped with the following antennas:
HF antenna (13.56 MHz)
Dimensions: 48 x 33 mm / 1.89 x 1.30 inch Number of turns: 3
LF antenna (125 kHz)
Dimensions: 49 x 34 mm / 1.93 x 1.34 inch Number of turns: 123
For more information, refer to the related product data sheet or other relevant technical documents.
LABEL AND COMPLIANCE INFORMATION
Refer to Chapters “Compliance Statements” and “Integrator and Host
Requirements” for detailed label and compliance information.
TEST MODES AND ADDITIONAL TESTING REQUIREMENTS
No specific testing method has been defined by ELATEC for TWN4 MultiTech 3
LEGIC M LF HF.
TWN4 MultiTech 3 LEGIC M LF HF has been tested and found in compliance with
the specifications noted on the approval certificates and other relevant
approval documents. However, the integrator is still responsible for any
additional testing and authorization process required for the end product.
Refer to the KDB Publication 996369 D04 Module Integration Guide of the FCC
Office of Engineering and Technology (OET) for detailed information about test
modes and additional testing requirements for the host device.
ADDITIONAL TESTING, PART 15 SUBPART B DISCLAIMER
TWN4 MultiTech 3 LEGIC M LF HF is only FCC authorized for the specific rule
parts (i.e., FCC transmitter rules) listed on the grant, and the host product
manufacturer is responsible for compliance to any other FCC rules that apply
to the host not covered by the modular transmitter grant of certification. In
addition, the final host product still requires Part 15 Subpart B compliance
testing with TWN4 MultiTech 3 LEGIC M LF HF installed.
MECHANICAL INSTALLATION
The reader module can be fixed into the host device with 3 screws M3.
ELECTRICAL CONNECTION
PROGRAMMATION/SOFTWARE INTEGRATION
n/a
COMPLIANCE STATEMENTS
-
EU
TWN4 MultiTech 3 LEGIC M LF HF is in compliance with the EU directives and regulations as listed in the respective declaration of conformity. -
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Caution
The Federal Communications Commission (FCC) warns the users that changes or
modifications to the unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FCC §15.105 (b)
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the Receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC ID: WP5TWN4F14
4.3 IC
This device complies with Industry Canada’s license-exempt RSSs. Operation is
subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
IC: 7948A-TWN4F14
RF EXPOSURE COMPLIANCE
RF exposure statement (mobile and fixed devices)
This device complies with the RF exposure requirements for mobile and fixed
devices. However, the device shall be used in such a manner that the potential
for human contact during normal operation is minimized.
INTEGRATOR AND HOST REQUIREMENTS
Authorization requirements
TWN4 MultiTech 3 LEGIC M LF HF has been certified as a module and does not
need further approval, provided that the module is used in accordance with the
FCC grant conditions and no limitations or usage conditions have been defined
by ELATEC. However, the host manufacturer must ensure that the host device
still complies with all applicable regulations after TWN4 MultiTech 3 LEGIC M
LF HF has been integrated.
In particular, the host integrator installing TWN4 MultiTech 3 LEGIC M LF HF
into their product must ensure that the final composite product complies with
the FCC requirements by a technical assessment or evaluation to the FCC rules,
including the transmitter operation and should refer to guidance in KDB
996369.
Labeling requirements
Using a permanently affixed label, TWN4 MultiTech 3 LEGIC M LF HF must be
labeled with its own FCC and IC identification numbers. In case this label is
not visible anymore after integration of TWN4 MultiTech 3 LEGIC M LF HF in the
host device, it is necessary to bring a label on the host device (on a visible
and accessible place) stating the FCC and IC identification numbers of the
integrated TWN4 MultiTech 3 LEGIC M LF HF:
Contains FCC ID: WP5TWN4F14
Contains IC: 7948A-TWN4F14
In case several modules have been integrated into the host device, the label
should state all FCC and IC identification numbers of the integrated modules.
Example: “Contains FCC IDs: XXX-XXXXXXX, YYY-YYYYYYY, ZZZ-ZZZZZZZ”.
Compliance statements
All statements listed in Chapter “Compliance statements” of this integration
manual must be also listed in the user manual of the host device.
Special accessories
Where special accessories such as shielded cables and/or special connectors
are required to comply with the emission limits, the instruction manual shall
include appropriate instructions on the first page of the text describing the
installation of the device.
Simultaneous transmission
When the host product supports simultaneous-transmission operations the host manufacturer needs to check if there are additional RF exposure filing requirements due to the simultaneous transmissions. When additional application filing for RF exposure compliance demonstration is not required (e. g. the RF module in combination with all simultaneously operating transmitters complies with the RF exposure simultaneous transmission SAR test exclusion requirements), the host manufacturer may do his own evaluation without any filing, using reasonable engineering judgment and testing for confirming compliance with out-of-band, restricted band, and spurious emission requirements in the simultaneous-transmission operating modes. If additional filing is required, please contact the person at ELATEC GmbH responsible for certification of the RF module.
APPENDIX
TERMS AND ABBREVIATIONS
| TERM | EXPLANATION |
|---|---|
| host device | Also “host” or “host product”. Device in which an RFID module is |
intended to be installed for operation.
Integrator| Responsible party for the integration of an RFID module into a
host device. The integrator might be the
module manufacturer, the host manufacturer, the end user or any other third party.
KDB| Knowledge Database
modular type| Physical configuration in which a modular transmitter operates
when installed within a host device. It can
be a single-modular, a limited single-modular, a split-modular or a limited split-modular type.
n/a| Not applicable
RFID (reader)
module
| Device intended to be used within another device or product. Depending on the equipment configuration
and intended use, an RFID module has to meet different requirements to get a modular grant.
B – RELEVANT DOCUMENTATION
ELASTIC documentation
- TWN4 MultiTech 3 LEGIC M LF HF data sheet
- TWN4 MultiTech 3 LEGIC M LF HF functional description
- TWN4 MultiTech 3 LEGIC M LF HF user manual
External documentation
| Document name | Document title/description | Source |
|---|---|---|
| n/a | Technical documentation related to the host product | Host product |
manufacturer
784748 D01 General labeling and Notification| General Guidelines for Labeling
and Other Information Required to be
Provided to Users
| Federal Communications Commission Office of Engineering and Technology
Laboratory Division
996369 D01 Module Equip Auth Guide
| Transmitter Module Equipment Authorization Guide| Federal Communications Commission Office of Engineering and Technology Laboratory Division
996369 D02 Module Q and A
| Frequently Asked Questions and Answers about Modules| Federal Communications Commission Office of Engineering and Technology
Laboratory Division
996369 D03 OEM Manual
| Guidance for Modular Transmitter Instruction Manuals and TCB Certification Application Reviews| Federal Communications Commission Office of Engineering and Technology Laboratory Division
996369 D04 Module Integration Guide
| Modular Transmitter Integration Guide— Guidance for Host Product
Manufacturers
| Federal Communications Commission Office of Engineering and Technology
Laboratory Division
RSS-Gen| General Requirements for Compliance of Radio Apparatus| Innovation, Science and Economic Development Canada
RSS-102
| Radio Frequency (RF) Exposure
Compliance of Radiocommunication Apparatus (All Frequency Bands)
| Innovation, Science and Economic Development Canada
Zeppelinstr
- 82178 Puchheim
- Germany P +49 89 552 9961 0
- F +49 89 552 9961 129
- E-mail: info-rfid@elatec.com
elatec.com
Elatec reserves the right to change any information or data in this document
without prior notice. Elatec declines all responsibility for the use of this
product with any other specification but the one mentioned above. Any
additional requirement for a specific customer application has to be validated
by the customer himself at his own responsibility. Where application
information is given, it is only advisory and does not form part of the
specification. Disclaimer: All names used in this document are registered
trademarks of their respective owners.
© 2021 ELATEC GmbH – TWN4 MultiTech 3 LEGIC M LF HF integration manual DocRev1
– 10/2021
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>