global sources K1176794579 HUD User Manual

global sources K1176794579 HUD

Thank you for selecting our Head-up Display products. Please read this User Manual carefully before using the Product to assure full use of functions and normal operation of the Product.

Product Introduction

This product is a head-up display device for automotive aftermarket. Through innovative product design concepts, the device enables you to use navigation, listen to music, make calls, and send and
receive messages while driving, without leaving your eyes from the road,and keep your hands on the steering wheel. Drive your car safer.

HUD Product Diagram

The HUD consists of three parts: the main body, the OBD connector , the connecting cable, and the remote control.

The main body

1. 3.5 mm audio output interface
2. Ambient light sensor detection hole
3. OBD connector
4. Reset hole
5. USB socket
6. Switch on/off
7. Base
8. Image combiner (Combiner)
9. MIC

The Composition of Base

1. Adhesive pad
2. Universal support table
3. Universal support table fastening screw (the screw has been adjusted to the fine adjustment of the universal support table before leaving the factory)

How to Separate the Base

Remote Control

1. Upper Selections（For Android Auto）
2. APP and vehicle information switch(long press enter menu)
3. OK
4. Previous item
5. Voice assistant
6. Lower Selections（For Android Auto）
7. Screen on and off
8. Next item
9. Buckle

OBD II

1. OBD Male and OBD Readout Circuit
2. TypeC

Operation Instructions

First Use

You can find the OBD port of your car at several locations in the figure. The port is shown in the lower-left corner.

• Connect OBD, use Type C to connect with product, and turn on the product.

• Start the car and the HUD will starting up about 3 seconds later (The start-up time of HUD is slightly different for different types of vehicles)

• Open the image combiner to the vertical position

• Adjust the combination of the base and the product, and fine-tune the angle of the image combiner to find a position where the image can be seen in the driving position, mark this location.

• Remove the base adhesive protection paper and attach the main body and the base to the center console. And make the final fine-tuning.

• Insert the mobile phone data cable into the USB interface and use the cable clips to organize the data cable and OBD cable.

• Fix the remote control on the steering wheel.

• for iPhone users
  Connect to the phone, HUD automatically wakes up Carplay function and projects the image onto the image combiner.

• for Google Auto users
  Please move to the Google app market to search for and install the Android Auto app designed by Google.
  For some mobile phones, you may also be asked to install some supporting apps;

• Connecting to the phone, HUD automatically launches the Google Auto interface and projects it onto the image combiner.

• Open the phone settings interface, search for HUT_BT Bluetooth device, and connect.

• If need PIN code during connect, input 0000.

• Use the steering wheel remote control
  Press and hold the “APP and vehicle information switch” button to open the setup menu. Set the FM frequency. Press and hold the same button to exit the menu settings.

• Turn on the radio and set it to the frequency as you just set.
  (At this point, you have completed preparation before use.)

• Daily use
  APP and vehicle information switching: single-press “APP and vehicle information switch” button to switch between OBD information and vehicle system

• Voice Assistant
  This HUD supports voice control. press the “Voice assistant” to activate the voice assistant. And say what you want to do, such as: call xxx, send massage xxx to xxx, start Waze, etc.

• APP startup and control
  You can use “Previous item” and “Next item” and “OK” buttons to start APP and control APP.
  For example, when the phone is dialed in, the interface is as follows: You can choose to answer or hang up or reply by message. After selecting, press the dial to confirm the selection.

• Off-Screen
  In some cases, you don’t need display. Then you can press the “off-screen” button to turn off the display.
  The device is still running at this time. The navigation played music continues. Press “Off Screen” key to toggle the display on / off whenever you need it.

• Google Auto users
  The GoogleAuto control is divided into two areas;
  Use the “Upper Selections” and “Lower Selections” buttons to switch between different selections, and then use “Previous item” and “Next item” and “OK” key to select the controls you want.

• The menu on the top left of Android can be selected by long pressing the “Upper Selections” button.

• Menu
  Press and hold the “APP and vehicle information switch” button to open the setup menu.

• In setup menu, you can set “Language”, “Speed unit” and FM frequency, Press “Comfirm” key to open options list for each item.

• In FM Frequency sub menu, you can use Previous item” and “Next item” key and “Upper selections” or “Lower Selections” to select transmit frequency. “OK key” to confirm your setting.

Technical parameters

FAQ

Why can’t I quit the app?
Some of the App’s Carplay versions are defective, leading to the use of turntable selection control, always in the control of APP circular selection, unable to return to the main menu. At this point, you can open other apps by voice and return to the main interface menu in other apps. You can give feedback to the APP designer.

Packaging accessories

1. Main unit
2. OBD line
3. Remote control
4. Cable clips
5. Instruction manual
6. Packing box

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>