Shenzhen Shi Aiker Electronic Technology AP05 Magnetic Wireless Charger Stand Instruction Manual

Magnetic Wireless Charger Stand

Product Introduction

Thanks for choosing us!
This is a Magnetic Wireless Charger Stand for iPhone with the latest version of iOS.Please read the manual carefully before using the product, and keep it properly for checking.

Features

1. There is a ring of magnets inside the product, which can be charged on the back of mobile phone through magnetic suction function ;
2. This product has two charging methods: magnetic suction type, bracket type;
3. This is an ultra-thin, small-size product and convenient to carry;
4. This product is an integrated wireless charger, not needing additional cable;
5. This product input port specification is USB-A&C, which can be matched with PD or QC adapter at will;
6. This product supports 15W fast charging.

Bracket Using Instructions

1. For magnetically using: Pull out the bracket to another end of the data cable, and it can be easily used, as Figure 1;
2. For standing using: Put the bracket pull to the back of the magnetic wireless charger, insert it into the stuck buckle position in Figure 2, and then put the charger on the desktop for vertical charging, freeing both hands.

Function Description

Place the mobile phone with magnetic attraction function on the wireless charger, and the built-in magnet of the wireless charger will automatically align, accurately adsorb to the mobile phone, and start wireless charging; For other mobile phones without magnetic attraction function, place the center of the mobile phone at the center of the wireless charging to be wirelessly charged!

Specification

Attention

1. Do not squeeze or collide.
2. Do not disassemble or throw into fire or water, to avoid cauing a short circuit leakage.
3. Do not use the wireless charger in high temperatures, humidity, or corrosive environment, avoid damaging the circuit and avoid leakage.
4. Do not close with a magnetic stripe or chip card (ID card, bank card, etc)to avoid magnetic failure.
5. please keep the distance at least 20cm between implantable medical devices (pacemakers, implantable cochlear, etc)and the wireless charger, to avoid potential interference with the medical device. 6
6. Take care of the children, to ensure that they won’t play with the wireless charger as a toy, to avoid unnecessary accidents.

NOTE: no power adapter, if you need it, please purchase separately.

FCC Statement
This device complies with Part 15 of the FCC rules. Operation is subject to thefollowing two conditions: 1) this device may not cause harmful interference, and 2)this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. During the operation of the device, a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected.

MADE IN CHINA

Documents / Resources

| Shenzhen Shi Aiker Electronic Technology AP05 Magnetic Wireless Charger Stand [pdf] Instruction Manual
AP05, 2AVG2-AP05, 2AVG2AP05, AP05 Magnetic Wireless Charger Stand, Magnetic Wireless Charger Stand, Charger Stand, Stand
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>