Shenzhen Shi Aiker Electronic Technology AP06 3-In-1 Magnetic Wireless Charging Pad Instruction Manual
- June 5, 2024
- Shenzhen Shi Aiker Electronic Technology
Table of Contents
Shenzhen Shi Aiker Electronic Technology AP06 3-In-1 Magnetic Wireless Charging Pad Instruction Manual
Product Introduction
Thanks for choosing us!
This is a 3 in 1 magnetic wireless charging pad, which is compatible with mobile phones, earbuds and watches with wireless charging function. please read the manual carefully before using the product, and keep properly for checking.
Operational Methods
The upgraded version magnetic wireless charge is compatible with three different wireless charging devices.
-
Qi-enabled mobile phones:Place the magnetic attraction mobile phone on the wireless charger, and the built-in magnet of the wireless charger will automatically align, accurately adsorb to the mobile phone, and start wireless charging;For other mobile phones without magnetic attraction function, can be charged wirelessly by placing the center position of the mobile phone in the wireless charger s center position.
-
Qi-enabled earbuds:Place the earbuds(with wireless charging case) in the wireless charger s center position to start wireless charging.
-
Qi-enabled watches:Only compatible with Apple watch 2 generation and above series magnetic watches,Place the watch on the wireless charger,it will automatically align, accurately adsorb to the watch, and start wireless charging.
Product Features
- Built in magnets,can be magnetically attached to the back of mobile phone and watch for easy use;
- This is a ultra-thin, small size product and convenient to carry;
- This product is an integrated wireless charger, not need additional cable;
- Data line input port specification is USB-C, supporting PD protocol;
- Charging power: mobile phone 15W quick charging, earphone 5W, watch 3W.
- The bottom of the product is designed with a circle non-slip silicone pad,which can prevent falling off when placed on the smooth table.
Product Specification
| Input | 9.0V 2.0A |
|---|---|
| Output | 15W(Max) |
| Frequency | 110-205KHz |
| Efficiency | 75% |
| Product Size | 58.7*8mm |
Attention
- Do not squeeze or collisions.
- Do not disassemble or throw into fire or water, to avoid cauing a short circuit leakage.
- Do not use the wireless charger in high temperature, humidity or corrosive environment,avoid damaging the circuit and avoid leakage.
- Do nof close with magnetic stripe or chip care (ID card,bank card ,ect)to avoid magnetic failure.
- Please keep the distance at least 20cm between implantable medical devices (pacemakers.implantable cochlear,etc)and the wireless charger ,to avoid potential interference with the medical device.
- Take care of the children,to ensure that they won’t play the wireless charger as a toy to avoid unnecessary accidents.
NOTE: No power adapter.If you need,please purchase separately.
FCC Caution
§ 15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
§ 15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning for Mobile device:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>