Fxtec F(x)tec Pro1 X User Guide
- October 27, 2023
- Fxtec
Table of Contents
F(x)tec Pro1 X
QUICK START GUIDE
F(x)tec Pro1 X
Thank you for choosing the Pro1 X. Before using the device, please read this
guide to help you get started. The full User Guide is available at
www.fxtec.com/support.
Getting To Know Your Phone
Familiarise yourself with the different parts of the phone as shown in the
diagram below.
Sliding Your Phone Open
- Lift the right side of the Pro1 X up slightly.
- Slide the screen up until the hinge locks into position
Inserting and Removing the SIM card
- To open the SIM card tray, place your fingernail into the ridge and carefully slide the tray out.
- Put the nano-SIM card into the slot located on the tray with the contact area facing down.
- Slide the SIM card tray back into the slot.
Charging Your Phone
To charge the phone, use the charger provided with your phone.
The charger type may vary according to country. Please use the one that is
relevant to your region. Plug the charger into a wall outlet and connect the
cable to the phone. A charging indicator will be displayed to indicate the
phone is charging.
Once fully charged, press and hold the Power button until the screen lights up
to switch your phone on.
The screen prompts will guide you through the setup.
Safety Information
Read all safety information before using the device to prevent injury to
yourself or others, to prevent damage to your device and to avoid breaking
local laws and regulations. See the full ‘Important Safety Information’ at
www.fxtec.com/support.
Handle Device with Care
The screen of this device is made of glass. This glass can break if the device
is dropped or receives a substantial impact. Should the glass break, do not
touch the glass parts or attempt to remove the broken glass.
Get the glass replaced by an authorised service personnel before using the
device.
Batteries, Chargers and Other Accessories
Only use manufacturer approved battery, charger and accessories for this
device. Do not use incompatible batteries or chargers as this may cause fire,
explosion, or other hazards. Using incompatible products may also damage your
device and invalidate the warranty.
Protect Your Hearing
Do not listen at high volume levels for long devices. Use caution when holding
the device near your ear while the loudspeaker is in use.
Road Safety
Obey local laws and regulations. Keep your hands free to operate the vehicle
while driving.
Switch off in Restricted Areas
Obey all instructions in restricted areas. All wireless devices may be
susceptible to interference.
Switch your device off when mobile phone use is not allowed or when it may
cause interference. Be aware of restrictions in areas such as in hospitals,
near petrol pumps, during flights or near medical equipment.
Authorised Service
Only send this device to authorised service personnel for repairs or
installations.
Do not open the device other than as instructed in the user guide.
Unauthorised modifications may damage the device and violate regulations and
invalidate the warranty.
Keep Device Dry
This device is not waterproof and has no IP rating. Exposure to liquid,
moisture and humidity can damage the parts or electronic circuits of the
device.
Specific Absorption Rate (SAR)
This device meets RF exposure guidelines when used either in the normal use
position against the ear or when positioned at least 5mm away from the body.
Mobile devices may be transmitting even when not on a voice call. Ensure that
any carry case, belt clip or other form of device holder does not contain
metal and should provide at least 5mm separation distance from the body.
Correct Disposal
The crossed-out wheelie bin symbol on your device, battery or packaging is a
reminder that all electrical and electronic products and batteries must be
taken to a separate collection point at the end of their working life.
DO NOT dispose of these products as unsorted municipal waste.
Always recycle your devices, batteries and packaging materials to dedicated
recycling points.
Check with your local waste authority for information on your nearest
recycling point.
Regulatory Information: EU
EU Compliance Notice
Hereby, FX Technology Limited declares that Pro1 X is in compliance with
Directive 2014/53/EU (Radio Equipment Directive). The full declaration of
conformity is below
EU Declaration of Conformity
FX Technology Limited
This declaration of conformity is issued for:
Radio Equipment model number: QX1050
Product name: Pro1 X
Software version: Android OS
Accessories supplied: USB-C earbud, AC adapter, USB-C to C cable
We, FX Technology Limited, declare under our sole responsibility that the
above named product(s) conform to the essential requirements of the following
European Union directives:
Radio Equipment Directive (RED)
RoHS Recast Directive
Ecodesign Requirements for Energy
Related Products Directive| 2014/53/EU
2011/65/EU
2009/125/EC
---|---
The conformity assessment procedure referred to in Article 10 and detailed in Annex III of the Radio Equipment Directive 2014/53/EU has been carried out by Test Laboratory. The following harmonized standards and normative documents are those to which the product’s conformance is declared, and by specific reference to the essential requirements of the referenced Directives:
Health & Safety
(Article 3.1(a) of the RED)| EN 62368-1:2014 + A11:2017
EN 62479:2010
EN 50360:2017, EN 62209-1:2016
EN 50566:2017, EN 62209-2:2010
---|---
EMC
(Article 3.1(b) of the RED)| ETSI EN 301 489-1 V2.2.3 (2019-11)
ETSI EN 301 489-3 V2.1.1 (2019-03)
ETSI EN 301 489-17 V3.2.4 (2020-09)
ETSI EN 301 489-19 V2.1.1 (2019-04)
ETSI EN 301 489-52 V1.2.1 (2021-11)
EN 55032:2015+A11:2020 / EN
5035:2017+A11:2020
EN IEC 61000-3-2:2019 / EN 61000-3-3:2013+A1:2019
Spectrum
(Article 3.2 of the RED)| ETSI EN 301 908-1 V13.1.1 (2019-11)
ETSI EN 301 908-2 V13.1.1 (2020-06)
ETSI EN 301 908-13 V13.1.1 (2019-11)
ETSI EN 303 413 V1.2.1 (2021-04)
ETSI EN 300 328 V2.2.2 (2019-07)
ETSI EN 301 893 V2.1.1 (2017-05)
ETSI EN 300 440 V2.2.1 (2018-07)
ETSI EN 303 345-1 V1.1.1 (2019-06)
ETSI EN 303 345-3 V1.1.1 (2021-06)
ETSI EN 300 330 V2.1.1 (2017-02)
Equipment within Certain Categories or Classes
(Article 3.3 of the RED)| N/A
Ecodesign Requirements Energy Related
Products Directive,
2009/125/EC| Regulation 1275/2008, Regulation for 278/2009
RoHS Recast Directive, 2011/65/EU| EN 50581:2012
Signed for and on the behalf of FX Technology Limited
Restrictions and Requirements under Directive 2014/53/EU
The device is restricted to indoor use only when operating in the 5150 to 5250
MHz frequency range in AT, BE, BG, CY, CZ, DE, DK, EE, EL, ES, FI, FR, HR, HU,
IE, IT, LT, LU, LV, MT, NL, PL, PT, RO, SE, SI, SK, UK, CH, IS, LI, NO, and
TR.
Frequency Bands and Power
European Union, United Kingdom
Data given here is the maximum radio-frequency power transmitted in the
frequency band(s) in which the radio equipment operates.
Frequency
WiFi 2 400-2 483,5 MHz
WiFi 5 150-5 250 MHz
Bluetooth: 2 400-2 483,5 MHz
NFC 13.56 MHz
GSM 900
GSM 1800
UMTS Band I/VIII
LTE:1, 3, 7, 8, 20, 28, 38, 40| Power
Max 20 dBm
Max 23 dBm
Max 20 dBm
Max. -10 dBuA/m
PC4 (Max 33 dBm)
PC1 (Max 31 dBm)
PC3 (Max 23 dBm)
PC3 (Max 23.5 dBm)
---|---
Restrictions in the 5 GHz Band
WLAN function of these devices is restricted only to indoor use when operating
in the 5150 to 5250 MHz frequency range to reduce the potential for harmful
interference to co-channel mobile satellite systems.
Radio frequency interference
FX Technology Limited is not responsible for any radio or television
interference caused by unauthorized modification of these devices or
accessories, or by the substitution or attachment of connecting cables and
equipment other than that specified by FX Technology Limited. The correction
of interference caused by such unauthorized modification, substitution, or
attachment is the responsibility of the user. FX Technology Limited and its
authorized resellers or distributors are not liable for any damage or
violation of government regulations that may arise from the user failing to
comply with these guidelines.
Specific Absorption Rate (SAR) information – EU
This device is classified for use in a typical Class B domestic environment.
The Pro1 X complies with radio frequency specifications when used near your
ear or at a distance of 0.5 cm from your body. Ensure that the device
accessories, such as a device case and device holster, are not composed of
metal components. Keep the device away from your body to meet the distance
requirement.
The highest Specific Absorption Rate (SAR) value reported for this device type
when tested at the ear is 0.913 W/kg, and when properly worn on the body is
1.412 W/kg.
Waste Electrical and Electronic Equipment (WEEE) & Batteries Directive
The Waste Electrical and Electronic Equipment (WEEE) Directive requires that
all Electrical and Electronic Equipment (EEE), including your phone and its
accessories, must be marked with the symbol of the crossed-out wheeled bin.
This symbol means that the equipment must not be disposed of as unsorted
municipal waste.
Disposing of WEEE together with normal waste may pose a risk to the
environment and to human health, due to certain substances used in EEE and
their batteries.
Under the WEEE Directive, each EU Member State is responsible for achieving a
high level of collection of WEEE for treatment, recovery, and environmentally
sound disposal.
The success of this EU policy will depend on your active contribution in
returning your WEEE to the appropriate facilities dedicated to the disposal of
such waste. You should contact your local authority or your retailer for
details about the return and collection points available.
RoHS Compliance
This product is in compliance with Directive 2011/65/EU of the European
Parliament and of the Council of 8 June 2011, on the restriction of the use of
certain hazardous substances in electrical and electronic equipment (RoHS) and
its amendments.
REACH
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals,
EC No 1907/2006) is the EU regulation addressing the safe production and use
of chemicals. FX Technology Limited complies with all requirements of the
regulation.
Manufacturer Info
Manufacturer: FX Technology Limited.
Regulatory information: United States
U.S. Federal Communications Commission’s (FCC) Regulatory Compliance
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from hat to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help
- Changes or modifications not expressly approved by FX Technology Limited could void your authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Radio Frequency Exposure
This device meets the U.S. Federal Communications Commission’s (FCC)
requirements for exposure to radio waves and is designed and manufactured not
to exceed the FCC’s emission limits for exposure to radio frequency (RF)
energy. For satisfying FCC RF exposure compliance requirements, body-worn
operations are restricted to belt clips, holsters or similar accessories that
have no metallic components in the assembly and must provide at least 10 mm
separation between the device, including its antenna, and the user’s body.
Specific Absorption Rate (SAR) Information
This device is designed to meet the requirements for exposure to radio waves
established by the Federal Communications Commission (USA).
The Specific Absorption Rate (SAR) limit adopted by the U.S. is 1.6 W/ kg
averaged over one gram of tissue. The highest SAR value reported to the FCC
for this device type complies with this limit. The Pro1 X complies with radio
frequency specifications w hen used near your ear or at a distance of 1.0 cm
(0.4 in) from your body. Ensure that the device accessories, such as a device
case and device holster, are not composed of metal components. Keep the device
away from your body to meet the distance requirement.
Regulatory information: Canada
Innovation, Science, and Economic Development (ISED) Canada,
Class B
This Class B digital apparatus complies with Canadian ICES-003.CAN and
ICES-3(B)/NMB-3(B).
Notice: The ISED Canada regulations provide that changes or modifications
not expressly approved by FX Technology Limited could void your authority to
operate this equipment.
Innovation, Science, and Economic Development (ISED) Canada Notices
The Pro1 X complies with ISED’s license-exempt RSS standard(s). Operation is
subject to the following two conditions:
- These devices may not cause interference.
- These devices must accept any interference, including interference that may cause undesired operation of the device.
The device for operation in the band 5150–5250 MHz is only for indoor use to
reduce the potential for harmful interference to cochannel mobile satellite
systems.
Specific Absorption Rate (SAR) Information
The radiated output power of the Pro1 X is below the ISED radio frequency
exposure limits. This device has been evaluated for and shown compliant with
the ISED Radio Frequency (RF) exposure limits.
This device should be used in a manner such that the potential for human
contact during normal operation is minimized.
When using the device next to your body (other than in your hand or against
your head), maintain a distance of 10 mm from your body, to be consistent with
how the device is tested for compliance with RF exposure requirements. Ensure
that the device accessories, such as a device case and device holster, are not
composed of metal components.
This device has been certified for use in Canada.
Status of the listing in the ISED’s REL (Radio Equipment List) can be found at
the following web address:
http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do
Additional Canadian information on RF exposure also can be found at the
following web address: http://www.ic.gc.ca/eic/site/smt-
gst.nsf/eng/sf08792.html
**Regulatory information: Japan**
When operating in 5GHz (W52/W53), the device is restricted to indoor use only
(except for the transmission with 5.2GHz High Power Data Communication System
Base Station or Relay Station).
This is a Class B equipment. Although this equipment is intended for use in a
residential environment, it could cause poor reception if used near a radio or
a television receiver. Please follow instructions in the instruction manual.
VCCI-B
The Pro1 X complies with Japan SAR regulations when used near your ear or at a
distance of 5 mm from your body. Ensure that the device accessories, such as a
device case and device holster, are not composed of metal components. Keep the
device away from your body to meet the distance requirement.
Pro1 X maximum SAR values as reported to the Japan Ministry of Internal
Affairs and Communications (MIC) are:
- 0.913 W/kg when holding it to your ear
- 1.412 W/kg when properly worn on the body
References
- Support - F(x)tec
- Support - F(x)tec
- Frequently Asked Questions (FAQ) on Radiofrequency (RF) Energy and Health
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>