ASUS XP4R Dual Band Powerline Mesh Wi-Fi System User Guide

ASUS XP4R Dual Band Powerline Mesh Wi-Fi System

Specifications

ZenWiFi Hybrid XP4 LED indications

• Solid blue
  Your AiMesh router or node is ready for setup.

• Solid white
  Your AiMesh router or node is online and works well.

• Solid amber
  The signal between your AiMesh router and the node is weak.

• Solid red
  Your AiMesh router has no Internet connection.
  Your AiMesh node is disconnected from the router.

• Blinking blue
  Your AiMesh router is applying new settings.

• Blinking amber
  Your AiMesh router or node is resetting.

• Solid purple
  Your AiMesh router or node is in rescue mode.

• Solid green
  Your AiMesh router or node is switching to another channel caused by system rebooting or radar signals detected on the current channel.

ASUS Router App

Download free ASUS Router APP to set up and manage your router(s).

Hardware Explanations ZenWiFi XP4 Overview

• WPS/PLC combo button
  Press this button to start WPS or PLC pairing.

• WPS pairing: Press the buttons
  on one of XP4 devices and a new wireless client to establish WiFi connection.
  PLC pairing: Press the buttons on one of XP4 devices in the existing Mesh System and a new XP4 device. After a short time, the new XP4 device will be integrated into your existing Mesh System.

• AC power connector
  Connect one end of the bundled power cord to this connector and the other end to a wall socket.

• Reset button
  Press this button to reset or restore the system to its factory settings.

• WAN port
  Connect your modem to this port with a network cable.

• LAN ports 1-2
  Connect your PC to a LAN port with a network cable.

• USB 3.1 Gen 1 port
  Insert a USB 3.1 Gen 1/ USB 2.0 device such as a USB disk or USB 3G/4G modem into this port.

AiMesh Setup Steps

1.  Find your AiMesh router and AiMesh node, and place them within 3 meters of each other during the setup process.
   WiFi Backhaul connection (Skip to Step 02).
   Ethernet Backhaul connection: Connect an Ethernet cable from the LAN port of the AiMesh router to the LAN port of the AiMesh node
   Powerline Backhaul connection (Skip to Step 02).

2. Connect the AiMesh router and AiMesh node to wall sockets using the bundled power cords.
   Do not use power extension cords to avoid degrading HomePlug signal and reducing data transfer speeds.
   To minimize powerline interference, connect the power cords to wall sockets directly.
   Plug the power cords to 3-prong outlets instead of 2-prong ones for higher data transfer speeds.

3. Use a network cable to connect your modem to the WAN port of the AiMesh router.

4. Wait until both LEDs turn solid blue indicating that devices are ready for the setup.

5. Enable Bluetooth on your phone and launch ASUS Router APP, and then follow the onscreen instructions to finish the AiMesh setup.

NOTES:

•  By default, the AiMesh router is paired with the AiMesh node, allowing you to quickly complete the setup. If the auto-pairing during the initial installation fails, you can manually pair the AiMesh router with the node by launching ASUS Router App or pressing the WPS/PLC combo button.
• To set the AiMesh router as the access point mode, go to web GUI (http://router.asus.com), and go to the page Administration > Operation Mode.

ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components, as well as packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for detailed recycling information in different regions.

REACH
Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals) regulatory framework, we published the chemical substances in our products at ASUS REACH website at http://csr.asus.com/english/REACH.htm

Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

•  This device may not cause harmful interference.
•  This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

WARNING! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Prohibition of Co-location
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
IMPORTANT NOTE:
Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End-users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC exposure compliance requirements, please follow operation instructions as documented in this manual.

WARNING! This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 35 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Compliance Statement of Innovation, Science and Economic Development Canada (ISED)
This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
For products available in the US/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.
Operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit. specified for point-to- point and non-point-to-point operation as appropriate.
CAN ICES-3(B)/NMB-3(B)
Radio Frequency (RF) Exposure Information
The radiated output power of the ASUS Wireless Device is below the Innovation, Science and Economic Development Canada radio frequency exposure limits. The ASUS Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized.
This equipment should be installed and operated with a minimum distance of 35 cm between the radiator any part of your body.
This device has been certified for use in Canada. Status of the listing in the Innovation, Science and Economic Development Canada’s REL (Radio Equipment List) can be found at the following web address:
http://www.ic.gc.ca/eic/site/ceb-bhst.nsf/eng/h_tt00020.html
Additional Canadian information on RF exposure also can be found at the following web:
https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html

Safety Notices

•  Use this product in environments with ambient temperatures between 0°C(32°F) and 40°C(104°F).
•  Refer to the rating label on the bottom of your product and ensure your power adapter complies with this rating.
• DO NOT place on uneven or unstable work surfaces. Seek servicing if the casing has been damaged.
•  DO NOT place or drop objects on top and do not shove any foreign objects into the product.
•  DO NOT expose to or use near liquids, rain, or moisture. DO NOT use the modem during electrical storms.
•  DO NOT cover the vents on the product to prevent the system from getting overheated.
• DO NOT use damaged power cords, accessories, or other peripherals.
•  If the Adapter is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.
•  To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system.
•  DO NOT mount this equipment higher than 2 meters.
• Utilisez ce produit dans un environnement dont la température ambiante est comprise entre 0˚C (32°F) et 40˚C (104°F).

Manufacturer| ASUSTeK Computer Inc.

Tel: +886-2-2894-3447

Address: 1F., No. 15, Lide Rd., Beitou Dist., Taipei City 112, Taiwan

---|---
Authorised representative in Europe| ASUS Computer GmbH

Address: HARKORT STR. 21-23, 40880 RATINGEN, GERMANY

Authorised| BOGAZICI BILGISAYAR TICARET VE SANAYI A.S.
distributors in Turkey| Tel./FAX No.: +90 212 331 10 00 / +90 212 332 28 90
| Address: ESENTEPE MAH. BUYUKDERE CAD. ERCAN HAN B BLOK NO.121 SISLI, ISTANBUL 34394
| CIZGI Elektronik San. Tic. Ltd. Sti.
| Tel./FAX No.: +90 212 356 70 70 / +90 212 356 70 69
| Address: GURSEL MAH. AKMAN SK.47B 1 KAGITHANE/ISTANBUL
| KOYUNCU ELEKTRONiK BiLGi iSLEM SiST. SAN. VE DIS TIC. A.S.
| Tel. No.: +90 216 5288888
| Address: EMEK MAH.ORDU CAD. NO:18, SARIGAZi, SANCAKTEPE ISTANBUL
| ENDEKS BİLİŞİM SAN VE DIŞ TİC LTD ŞTİ
| Tel./FAX No.: +90 216 523 35 70 / +90 216 523 35 71
| Address: NECIP FAZIL BULVARI, KEYAP CARSI SITESI, G1 BLOK, NO:115 Y.DUDULLU, UMRANIYE,
| ISTANBUL
| PENTA TEKNOLOJI URUNLERI DAGITIM TICARET A.S
| Tel./FAX No.: +90 216 528 0000
| Address: ORGANIZE SANAYI BOLGESI NATO YOLU 4.CADDE NO:1 UMRANIYE, ISTANBUL 34775

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>