KRAMER K-CamHD PTZ Camera User Manual

KRAMER K-CamHD PTZ Camera

Introduction

Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creative, and affordable solutions to the vast range of problems that confront the video, audio, presentation, and broadcasting professional on a daily basis. In recent years, we have redesigned and upgraded most of our line, making the best even better!

Getting Started

We recommend that you:

• Unpack the equipment carefully and save the original box and packaging materials for possible future shipment.
• Review the contents of this user manual.

Go to www.kramerav.com/downloads/K-CamHD to check for up-to-date user manuals, application programs, and to check if firmware upgrades are available (where appropriate).

Achieving Best Performance

• Use only good quality connection cables (we recommend Kramer high-performance, high-resolution cables) to avoid interference, deterioration in signal quality due to poor matching, and elevated noise levels (often associated with low quality cables).
• Do not secure the cables in tight bundles or roll the slack into tight coils.
• Avoid interference from neighboring electrical appliances that may adversely influence signal quality.
• Position your Kramer K-CamHD away from moisture, excessive sunlight and dust.

Safety Instructions
Caution:

• This equipment is to be used only inside a building. It may only be connected to other equipment that is installed inside a building.
• For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.
• There are no operator serviceable parts inside the unit.

Warning:

• Use only the power cord that is supplied with the unit.
• To ensure continuous risk protection, replace fuses only according to the rating specified on the product label which is located on the bottom of the unit.

Recycling Kramer Products
The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to reduce the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected and recycled. To comply with the WEEE Directive, Kramer Electronics has made arrangements with the European Advanced Recycling Network (EARN) and will cover any costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on arrival at the EARN facility. For details of Kramer’s recycling arrangements in your particular country go to our recycling pages at www.kramerav.com/il/quality/environment.

Overview

K-CamHD provides great image quality, even in low-light conditions, and easy access to medium and large size conferencing. K-CamHD combines 1080p image quality, 12x optical zoom, intelligent color optimization technology, ultra- low CMOS image sensors as well as 2D and 3D DNR technology.
Go to www.kramerav.com/downloads/K-CamHD to download the latest user manual and check if firmware upgrades are available.

K- CamHD provides exceptional quality, advanced and user-friendly operation, and flexible control.

• Smooth PTZ operation – featuring a horizontal field of view (HFoV) of 72.5°, easy pan (±170°) and tilt (±30°) ensuring complete coverage.
• High quality zoom – 12x optical zoom and 16x digital zoom providing a crystal-clear image and highly accurate close-ups.
• Simple plug and play – connecting via USB 3.0.
• Built-in noise reduction – delivers clear image quality, even in low light situations with 2D and 3D DNR and WDR technology.
• High-end camera lens – provides 1080p professional visuals.
• Flexible camera – works with a host of meeting devices based on RS-232 protocol communication.

Typical Applications

K- CamHD is ideal for the following typical applications:

• Hybrid video conferencing in meeting rooms.

Controlling your K-CamHD
Control your K-CamHD via:

• RS-232 serial commands (VISCA protocol) transmitted by a touch screen system, PC, or other serial controller.
• Remotely, from the infrared remote control transmitter.
• OSD menu.

Defining K-CamHD PTZ Camera

This section defines K-CamHD.

system controller).
8| OUT| Connect to a device with an RS-232 port (for example, a camera).
9| 12V DC Power Connector| Connect to the 12V power adapter.

Mounting K-CamHD

This section provides instructions for mounting K-CamHD. Before installing, verify that the environment is within the recommended range:

• Operation temperature – 0ï‚° to 40ï‚°C (32ï‚° to 104ï‚°F).
• Storage temperature – -20ï‚° to +60ï‚°C (-4ï‚° to +140ï‚°F).
• Humidity – 10% to 90%, RHL non-condensing.

Caution:

• Mount K-CamHD before connecting any cables or power.

Warning:

• Ensure that the environment (e.g., maximum ambient temperature & air flow) is compatible for the device.
• Avoid uneven mechanical loading.
• Keep away from children – product includes small accessories and components.
• Appropriate consideration of equipment nameplate ratings should be used for avoiding overloading of the circuits.
• Reliable earthing of rack-mounted equipment should be maintained.
• Maximum mounting height for the device is 2 meters.

Mounting K-CamHD

You can mount your camera to a wall, ceiling, or place it on a surface. A built-in gravity sensor automatically corrects the image orientation enabling mounting K-CamHD straight or upside-down.
Note that you can also attach the device upside down, from under the bracket.
To mount K-CamHD on a wall:

1. find the correct location on the wall.

2. In the desired location, drill 4 holes 82mm and 60mm apart (using a 6mm drill-bit) to fit the 4 holes of the wall-mounting bracket.

3. Insert the four expansion plugs into the holes.
   

4. Attach the wall bracket to the wall, using the four wall-bracket screws.
   You can place the bracket upside-down to mount the camera the other way around.
   

5. Attach the device to the wall bracket by fitting the mortise (on the bracket) into the tenon (on the camera).

6. Fix the camera by screwing (A) Nickel screw to the center and (B) then tighten with 3 black screws.
   

K-CamHD is mounted on the wall.

Connecting K-CamHD

Always switch off the power to each device before connecting it to your K-CamHD. After connecting your K-CamHD, connect its power and then switch on the power to each device.

To connect K-CamHD as illustrated in the example in figure above:

1. Connect the USB 3.0 port 5 to a laptop.
2. Connect a microphone to the LINE IN 3.5 Mini Jack 6.
3. Connect the RS232 OUT 8-pin DIN Connector 8 to an additional Camera.
4. Connect a control system to the RS232 IN 8-pin DIN Connector 7.
5. Connect the power adapter to K-CamHD and to the mains electricity.

Connecting to K-CamHD via RS-232

You can connect to K-CamHD via an RS-232 connection 7 / 8 using, for example, a PC or an additional camera.

Connect the K-CamHD RS-232 8-pin Min DIN connector to an RS-232 9-pin D-sub serial port, as follows:

Operating and Controlling K-CamHD

After connecting the K-CamHD and connecting the power. The device initializes, and the POWER LED lights green. The camera is ready for operation.

Controlling Via IR Remote Control Transmitter

Use the IR remote control to control K-CamHD and the OSD to configure it. Use shortcut keys for quick settings.

operation mode.
2| Number (0 to 9)| Configure or edit a preset.
3| Key| Use together with other keys for various functions.
4| PRESET| Press PRESET + a numerical key (0 to 9) to save the current configuration to that preset number.
5| HOME| Press to return K-CamHD to its default position.
When in the OSD, press to enter a submenu or confirm menu.
6| Return| Return to previous item on the menu.
7| ZOOM| SLOW| Press for slow zoom in (+) or out (-).
FAST| Press for quick zoom in (+) or out (-).
8| L/R Set| STD (1)| Press L/R + STD (1) keys to set Pan-Tilt to same direction as L/R setting.
REV (2)| Press L/R + REV (2) keys to set Pan-Tilt to the direction opposite to the L/R setting.
9| FOCUS| AUTO| Press to automatically set the focus to the center of the image.
MANUAL| Press to enter manual focus mode. Then press FAR or NEAR.
FAR| When in MANUAL mode, press to focus on a far object
NEAR| When in MANUAL mode, press to focus on a near object.
10| CAMERA SELECT| Select the camera to configure and control (1 to 4).
11| # Key| Use together with other keys for various functions.
12| IR R| Press + # + (F1 to F4) to assign a camera address to the remote. For example, point the remote to a camera, press +#+F1. The remote assigns CAMERA SELECT 1 key to this camera. To use the remote to control camera 1 press the CAMERA SELECT 1 key
Press F4 to freeze the image.
13| RESET| Press RESET+ a key number (0 to 9) to delete a preset configuration. Press +#+RESET to delete all preset configurations.
14| PTZ Control| Control camera panning and tilting using arrow keys (left, right, up, and down).
15| MENU| Enter/exit OSD menu
16| BACKLIGHT| Press to turn backlight compensation on or off.
Available when exposure mode is set to Auto (via the OSD menu).
17| P/T RST| Press to self-check preset Pan/Tilt on camera.

Assigning up to 4 K-CamHD Units to the IR Remote Controller
You can use one IR remote controller to control several cameras. To do so, you need to assign each device to the remote controller via IR learning.
To assign a device to the IR remote controller:

1. Turn the camera on.
2. Point the IR controller towards the front panel of the camera and press the following keys:
   • To assign Camera 1 – Press *, # and F1 simultaneously to set IR address to “CAMERA SELECT 1”.
   • To assign Camera 2 – Press *, # and F2 simultaneously to set IR address to “CAMERA SELECT 2”.
   • To assign Camera 3 – Press *, # and F3 simultaneously to set IR address to “CAMERA SELECT 3”.
   • To assign Camera 4 – Press *, # and F4 simultaneously to set IR address to “CAMERA SELECT 4”.

When assigning a camera to the remote, make sure you point directly to that camera and check that the other cameras in the area are powered down.
Cameras are assigned to IR remote controller.

Freezing an Image
You can freeze/unfreeze an image manually:

• To freeze an image, press F4 on the remote controller. The image freezes and the display shows “Freeze” on the top left side for 5 seconds.
• To Unfreeze the image, press F4 (once again) on the remote controller. The image unfreezes and the display shows “Unfreeze” on the top left side for 5 seconds.

Shortcut Keys
Use the following shortcut keys to set the following:

• *+＃+1: OSD default (English).
• *+＃+3: OSD default (Chinese).
• *+＃+6: Quickly recover the default.
• *+＃+8: View the camera version.
• *+＃+9: Quickly set up inversion.
• *+＃+MANUAL: Restore default IP address.

Operating Via the OSD Menu

K-CamHD enables controlling and defining the device parameters via the OSD, using the IR remote control MENU buttons.
To enter and use the OSD menu buttons:

1. Press MENU.
2. Press:
   • Arrow buttons to move through the OSD menu, which is displayed on the video output.
   • HOME to enter a submenu and accept changes and to change the menu settings.

Configuring Camera Exposure
K-CamHD enables configuring exposure parameters:
To adjust the image parameters:

1. On the IR remote press MENU. The menu appears.
2. Use the arrows to select Exposure.
3. Click HOME to enter Exposure menu. Adjust the following:

mode includes the relevant sub-menu settings.
Auto| Automatic exposure settings.
Manual| Control exposure settings manually.
SAE| Shutter Automatic Exposure.
AAE| Aperture Automatic Exposure.
Bright| Adjusts the brightness level manually
Sub-Menu| Function| Enabled in:
ExpCompMode| Select On to allow changes to the automatically-set exposure.
Select Off to keep auto settings.| Auto mode
ExpComp| Adjust the exposure compensation from -7 to 7.| Auto mode and ExpCompMode=On
Backlight| Select On to allow backlight compensation. Select Off to keep auto settings.| Auto mode
Bright| Control brightness level from 0 to 17.| Bright mode
Gain Limit| Set maximum gain limit from 0 to 15.| Auto, SAE, AAE and Bright modes
Anti-Flicker| Set anti flicker to Off, 50Hz or 60Hz.| Auto, AAE and Bright modes
Meter| Select the exposure meter to Average, Center, Smart or Top.| All modes
Iris| Set the aperture value to F1.8, F2.0, F2.4, F2.8, F3.4, F4.0, F4.8, F5.6, F6.8, F8.0, F9.6, F11.0 or Close.| Manual and AAE modes
Shutter| 1/30, 1/60, 1/90, 1/100, 1/125, 1/180, 1/250, 1/350, 1/500, 1/725, 1/1000, 1/1500, 1/2000, 1/3000, 1/4000, 1/6000 or 1/10000.| Manual and SAE modes
Gain| Set gain from 0 to 7.| Manual mode
DRC| Set Dynamic Range Compression strength from 0 to 8.| All modes

Exposure is configured.

Configuring Color Settings
K-CamHD enables configuring color parameters.
To adjust the color parameters:

1. On the IR remote press MENU. The menu appears.
2. Use the arrows to select Color.
3. Click HOME to enter Color menu. Adjust the following:
   Menu Item| Function
   ---|---
   WB Mode| Set white balance mode to Auto, Indoor, Outdoor, One Push, Manual.
   RG Tuning| Fine tune red gain from -10 to 10 (enabled in Auto mode).
   BG Tuning| Fine tune blue gain from -10 to 10 (enabled in Auto mode).
   Saturation| Set the color saturation from 60% to 200%.
   Hue| Set the color hue from -10 to 10.
   RG| Set red gain from 0 to 255 (enabled in Manual mode).
   BG| Set blue gain from 0 to 255 (enabled in Manual mode).

Color parameters are adjusted.

Setting Image Parameters
K-CamHD enables configuring image parameters.
To adjust the image parameters:

1. On the IR remote press MENU. The menu appears.
2. Use the arrows to select Image.
3. Click HOME to enter Image menu. Adjust the following:
   Menu Item| Function
   ---|---
   Luminance| Adjust luminance from 0 to 14.
   Contrast| Adjust contrast from 0 to 14.
   Sharpness| Adjust sharpness from 0 to 14.
   Flip-H| Define horizontal flip to On or Off.
   Flip-V| Define vertical flip On or Off.
   B&W Mode| Set black and white mode to On or Off.
   Style| Set the image style to Norm, Bright or PC.

Image parameters are adjusted.

Setting P/T/Z Parameters
K-CamHD enables configuring pan tilt and zoom parameters.
To adjust the P/T/Z parameters:

1. On the IR remote press MENU. The menu appears.
2. Use the arrows to select P/T/Z.
3. Click HOME to enter P/T/Z menu. Adjust the following:
   Menu Item| Function
   ---|---
   SpeedByZoom| Set to On, to control pan and tilt speed as a function of zoom.
   AF-Zone| Set auto focus to front, center top or bottom area.
   AF Sense| Set auto focus sensitivity to low, normal or high.
   L/R Set| Set pan direction to STD (Standard) or REV (Reverse).
   Display Info| Set to On, to display information or set to Off.
   Image Freeze| Set to On, to freeze the image before recalling a preset. Once the camera points to the recalled preset position, the camera returns to normal operation.
   Digital Zoom| Set digital zoom to 2x, 4x, 8x or 16x.
   Call Preset Speed| Adjust the pan and tilt movement speed from 1 (lowest) to 24 (highest).
   Pre Zoom Speed| Adjust the preset zoom speed from 0 to 7.

Pan tilt and zoom parameters are adjusted.

Setting Digital Noise Reduction Level
Set 3D noise reduction for a clearer picture when light conditions are low.
To set noise reduction level:

1. On the IR remote press MENU. The menu appears.
2. Use the arrows to select NR3D-Level.
3. Click HOME to enter NR3D-Level menu.
4. Set the noise reduction level from 1 to 9, or set to Off.

Noise reduction level is set.

Defining Setup Parameters
Define general setup parameters.
To define setup parameters:

1. On the IR remote press MENU. The menu appears.
2. Use the arrows to select SETUP.
3. Click HOME to enter SETUP menu. Define the following:
   Menu Item| Function
   ---|---
   Language| Define the user language: English, Chinese or Russian.
   Auto Patrol| Set to On or Off.
   SDI-3G Mode| Set to LEVEL-A or LEVEL-B mapping.
   Auto Flip| Set to On, for automatic flip of the view.
   USB Audio| Set to On or Off.
   OSD Flip| Set flipping the OSD to On or Off.

Setup parameters are defined.
To define communication parameters:

1. On the IR remote press MENU. The menu appears.
2. Use the arrows to select COMMUNICATION SETUP.
3. Click HOME to enter SETUP menu. Define the following:
   Menu Item| Function
   ---|---
   Protocol| Select the control protocol to VISCA, PELCO-D or PELCO-P.
   V_Address| Set the number of a camera in a daisy-chain setting (1 to 7). Set the first camera to 1 the second in the chain to 2, and so on (enabled in Auto mode, when VISCA protocol is selected).
   To daisy-chain cameras you need to use the VISCA protocol, Net Mode to Serial and set the baud rate to 9600 (default).
   V_AddrFix| Set to On or Off.
   Net Mode| Set to serial port Network control to Serial or Paral.
   Baudrate| Select 2400, 4800, 9600 or 38400.

Setup parameters are defined.

Restoring to Default Settings
To restore default settings:

1. On the IR remote press MENU. The menu appears.
2. Use the arrows to select RESTORE DEFAULT.
3. Click HOME to enter RESTORE DEFAULT menu.
4. Select Restore and then select Yes.

Default settings are restored.

Upgrading Firmware

Contact Tech support if you need to upgrade the firmware (support@kramerav.com).

Technical Specifications

USB Features

| Operating System| Windows 7, Windows 8, Windows 10, Mac OS X, Linux, Android
Color System / Compression| YUV 4:2:2 / H.264 / MJPEG
Controls| IR Remote Control Transmitter| OSD
PC| RS-232 protocol VISCA commands
Power| Source| 12V DC, 2A max.
Consumption| 12V DC, 800mA max.
Environmental Conditions| Operating Temperature| 0° to +40°C (32° to 104°F)
Storage Temperature| -20° to +60°C (-4° to 140°F)
Humidity| 10% to 90%, RHL non-condensing
Altitude| Below 5000 meters
Regulatory Compliance| Safety| CE, FCC
Environmental| RoHs, Reach
Enclosure| Type| Aluminum and plastic
General| Net Dimensions
(W, D, H)| 14.5cm x 9.8cm x 15cm (5.8″ x 3.8″ x 5.9″)
Shipping Dimensions
(W, D, H)| 23cm x 23cm x 25cm (9″ x 9″ x 9.8″)
Net Weight| 0.94kg (2.1lbs) approx.
Shipping Weight| 2.61kg (5.7lbs) approx.
Accessories| Included| Power adapter and cord, 1 USB-C cable, remote controller, wall bracket, screws set, lens cover

Default Communication Parameters

RS-232

Baud Rate:| 9600
Data Bits:| 8
Stop Bits:| 1
Parity:| None
Command Format:| ASCII
Full Factory Reset
OSD| Go to: Menu-> RESTORE DEFAULT -> confirm
Reset button| Press the RESET button for 5 seconds to reset the machine

The warranty obligations of Kramer Electronics Inc. (“Kramer Electronics”) for this product are limited to the terms set forth below:

What is Covered
This limited warranty covers defects in materials and workmanship in this product.

What is Not Covered
This limited warranty does not cover any damage, deterioration or malfunction resulting from any alteration, modification, improper or unreasonable use or maintenance, misuse, abuse, accident, neglect, exposure to excess moisture, fire, improper packing and shipping (such claims must be presented to the carrier), lightning, power surges, or other acts of nature. This limited warranty does not cover any damage, deterioration or malfunction resulting from the installation or removal of this product from any installation, any unauthorized tampering with this product, any repairs attempted by anyone unauthorized by Kramer Electronics to make such repairs, or any other cause which does not relate directly to a defect in materials and/or workmanship of this product. This limited warranty does not cover cartons, equipment enclosures, cables or accessories used in conjunction with this product.
Without limiting any other exclusion herein, Kramer Electronics does not warrant that the product covered hereby, including, without limitation, the technology and/or integrated circuit(s) included in the product, will not become obsolete or that such items are or will remain compatible with any other product or technology with which the product may be used.

How Long this Coverage Lasts
The standard limited warranty for Kramer products is seven (7) years from the date of original purchase, with the following exceptions:

1. All Kramer VIA hardware products are covered by a standard three (3) year warranty for the VIA hardware and a standard three (3) year warranty for firmware and software updates; all Kramer VIA accessories, adapters, tags, and dongles are covered by a standard one (1) year warranty.
2. Kramer fiber optic cables, adapter-size fiber optic extenders, pluggable optical modules, active cables, cable retractors, ring mounted adapters, portable power chargers, Kramer speakers, and Kramer touch panels are covered by a standard one (1) year warranty. Kramer 7-inch touch panels purchased on or after April 1st, 2020 are covered by a standard two (2) year warranty.
3. All Kramer Calibre products, all Kramer Minicom digital signage products, all HighSecLabs products, all streaming, and all wi reless products are covered by a standard three (3) year warranty.
4. All Sierra Video MultiViewers are covered by a standard five (5) year warranty.
5. Sierra switchers & control panels are covered by a standard seven (7) year warranty (excluding power supplies and fans that are covered for three (3) years).
6. K-Touch software is covered by a standard one (1) year warranty for software updates.
7. All Kramer passive cables are covered by a lifetime warranty.

Who is Covered
Only the original purchaser of this product is covered under this limited warranty. This limited warranty is not transferable to subsequent purchasers or owners of this product.

What Kramer Electronics Will Do
Kramer Electronics will, at its sole option, provide one of the following three remedies to whatever extent it shall deem necessary to satisfy a proper claim under this limited warranty:

1. Elect to repair or facilitate the repair of any defective parts within a reasonable period of time, free of any charge for the necessary parts and labor to complete the repair and restore this product to its proper operating condition. Kramer Electronics will also pay the shipping costs necessary to return this product once the repair is complete.
2. Replace this product with a direct replacement or with a similar product deemed by Kramer Electronics to perform substantially the same function as the original product. If a direct or similar replacement product is supplied, the original product’s end warranty date remains unchanged and is transferred to the replacement product.
3. Issue a refund of the original purchase price less depreciation to be determined based on the age of the product at the time remedy is sought under this limited warranty.

What Kramer Electronics Will Not Do Under This Limited Warranty
If this product is returned to Kramer Electronics or the authorized dealer from which it was purchased or any other party authorized to repair Kramer Electronics products, this product must be insured during shipment, with the insurance and shipping charges prepaid by you. If this product is returned uninsured, you assume all risks of loss or damage during shipment. Kramer Electronics will not be responsible for any costs related to the removal or re-installation of this product from or into any installation. Kramer Electronics will not be responsible for any costs related to any setting up this product, any adjustment of user controls or any programming required for a specific installation of this product.

How to Obtain a Remedy Under This Limited Warranty
To obtain a remedy under this limited warranty, you must contact either the authorized Kramer Electronics reseller from whom you purchased this product or the Kramer Electronics office nearest you. For a list of authorized Kramer Electronics resellers and/or Kramer Electronics authorized service providers, visit our web site at www.kramerav.com or contact the Kramer Electronics office nearest you.
In order to pursue any remedy under this limited warranty, you must possess an original, dated receipt as proof of purchase from an authorized Kramer Electronics reseller. If this product is returned under this limited warranty, a return authorization number, obtained from Kramer Electronics, will be required (RMA number). You may also be directed to an authorized reseller or a person authorized by Kramer Electronics to repair the product.
If it is decided that this product should be returned directly to Kramer Electronics, this product should be properly packed, preferably in the original carton, for shipping. Cartons not bearing a return authorization number will be refused.

Limitation of Liability
THE MAXIMUM LIABILITY OF KRAMER ELECTRONICS UNDER THIS LIMITED WARRANTY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID FOR THE PRODUCT. TO THE MAXIMUM EXTENT PERMITTED BY LAW, KRAMER ELECTRONICS IS NOT RESPONSIBLE FOR DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION, OR UNDER ANY OTHER LEGAL THEORY. Some countries, districts or states do not allow the exclusion or limitation of relief, special, incidental, consequential or indirect damages, or the limitation of liability to specified amounts, so the above limitations or exclusions may not apply to you.

Exclusive Remedy
TO THE MAXIMUM EXTENT PERMITTED BY LAW, THIS LIMITED WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, REMEDIES AND CONDITIONS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. TO THE MAXIMUM EXTENT PERMITTED BY LAW, KRAMER ELECTRONICS SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IF KRAMER ELECTRONICS CANNOT LAWFULLY DISCLAIM OR EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW, THEN ALL IMPLIED WARRANTIES COVERING THIS PRODUCT, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY TO THIS PRODUCT AS PROVIDED UNDER APPLICABLE LAW.
IF ANY PRODUCT TO WHICH THIS LIMITED WARRANTY APPLIES IS A “CONSUMER PRODUCT” UNDER THE MAGNUSON-MOSS WARRANTY ACT (15 U.S.C.A. §2301, ET SEQ.) OR OTHER APPLICABLE LAW, THE FOREGOING DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT APPLY TO YOU, AND ALL IMPLIED WARRANTIES ON THIS PRODUCT, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR THE PARTICULAR PURPOSE, SHALL APPLY AS PROVIDED UNDER APPLICABLE LAW.

Other Conditions
This limited warranty gives you specific legal rights, and you may have other rights which vary from country to country or state to state.
This limited warranty is void if (i) the label bearing the serial number of this product has been removed or defaced, (ii) the product is not distributed by Kramer Electronics or (iii) this product is not purchased from an authorized Kramer Electronics reseller. If you are unsure whether a reseller is an authorized Kramer Electronics reseller, visit our web site at www.kramerav.com or contact a Kramer Electronics office from the list at the end of this document.
Your rights under this limited warranty are not diminished if you do not complete and return the product registration form or complete and submit the online product registration form. Kramer Electronics thanks you for purchasing a Kramer Electronics product. We hope it will give you years of satisfaction.

SAFETY WARNING
Disconnect the unit from the power supply before opening and servicing

For the latest information on our products and a list of Kramer distributors, visit our website where updates to this user manual may be found.
We welcome your questions, comments, and feedback.
All brand names, product names, and trademarks are the property of their respective owners.

www.KramerAV.com
info@KramerAV.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>