wifiworld UF-AE Media Converter User Guide
- June 6, 2024
- wifiworld
Table of Contents
wifiworld UF-AE Media Converter
Package Contents
Installation Requirement
The UF-AE requires an active fiber SFP module and does not support passive
GPON SFP modules.
Hardware Overview
Ports
SFP Port
The hot-swappable SFP port supports a 1 Gbps connection. (You can use an SFP+
module; however, the maximum speed is 1 Gbps.)
Ethernet Port
The RJ45 Ethernet port supports a 10/100/1000 connection. To power the device,
the port also supports 802.3af active PoE or 24V passive PoE.
Ethernet LED
Off| Ethernet connection down
Amber| 10/100 Mbps Ethernet connection up Flashing indicates activity
White| 1000 Mbps (1 Gbps) Ethernet connection up Flashing indicates activity
Off| Optical signal present
---|---
Amber| Loss of optical signal
Check the fiber cable for damage and ensure that it is properly connected on both ends.
Power LED
Off| Power off
White| Power on
Hardware Installation
Wall Mounting
Connecting Fiber
The UF-AE requires an active fiber SFP module and does not support passive
GPON SFP modules.
Note: You can use an SFP+ module; however, the maximum speed is 1 Gbps.
Connecting LAN
Connecting Power
OR
Note: The airCube AC provides a 1 Gbps Ethernet connection and Wi-Fi connectivity with PoE passthrough, so it is the ideal complement to the device for CPE installations.
OR
WARNING: The switch port must comply with the power specifications listed in this Quick Start Guide.
Specifications
UF-AE
Dimensions| 76.5 x 76.5 x 26.4 mm
(3.01 x 3.01 x 1.04″)
Weight| 68 g (2.40 oz)
Networking Interfaces| (1) 1 Gbps SFP Port
(1) 10/100/1000 Mbps RJ45 Port
---|---
Power Method| 802.3af PoE: (Pins 1, 2+; 3, 6-)
24V Passive PoE: (Pins 4, 5+; 7, 😎
Power Supply| 802.3af PoE or 24V Passive PoE Device*
Max. Power Consumption| 1.5W
Supported Voltage Range| 16 to 57V
LEDs| (1) Ethernet
(1) Optical Signal
(1) Power
Operating Temperature| -40 to 60° C (-40 to 140° F)
Operating Humidity| 10 to 90% Noncondensing
ESD/EMP Protection| ± 12kV Contact/Air
Certifications| CE, FCC, IC
Safety Notices
- Read, follow, and keep these instructions.
- Heed all warnings.
- Only use attachments/accessories specified by the manufacturer.
WARNING:
- To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
- Do not use this product in location that can be submerged by water.
- Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.
- CLASS 1 LASER PRODUCT – Do not look into the ends of the fiber optic cable or SFP modules while converters are powered.
Electrical Safety Information
- Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those
- There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician.
Limited Warranty
ui.com/support/warranty
The limited warranty requires the use of arbitration to resolve disputes on an
individual basis, and, where applicable, specify arbitration instead of jury
trials or class actions.
FCC
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions.
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
ISED Canada
CAN ICES-3(A)/NMB-3(A)
Australia and New Zealand
Warning: This equipment is compliant with Class A of CISPR 32. In a
residential environment this equipment may cause radio interference.
CE Marking
CE marking on this product represents the product is in compliance with all
directives that are applicable to it.
Declaration of Conformity
Online Resources
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>