iWave iW-RainboW-G22D G1E SODIMM SOM Development Platform User Guide
- June 6, 2024
- iWave
Table of Contents
- iWave iW-RainboW-G22D G1E SODIMM SOM Development Platform
- UNPACKING
- Quick Start Guide
- Package Checklist
- Get to know the RZ/G1E Development Platform
- SETTING UP THE TEST ENVIRONMENT
- Power Supply Connection
- DVD Contents
- iWave’s other Products
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
iWave iW-RainboW-G22D G1E SODIMM SOM Development Platform
Disclaimer
iWave Systems reserves the right to change details in this publication
including but not limited to any Product specification without notice.
No warranty of accuracy is given concerning the contents of the information
contained in this publication. To the extent permitted by law no liability
(including liability to any person by reason of negligence) will be accepted
by iWave Systems, its subsidiaries or employees for any direct or indirect
loss or damage caused by omissions from or inaccuracies in this document.
Trademarks
All registered trademarks, product names mentioned in this publication are the
property of their respective owners and used for identification purposes only.
Certification
iWave Systems Technologies Pvt. Ltd. is an ISO 9001:2015 Certified Company.
Warranty & RMA
Warranty support for Hardware: 1 Year from iWave or iWave’s EMS partner. For
warranty terms, go through the below web link,
http://www.iwavesystems.com/support/warranty.html
For Return Merchandise Authorization (RMA), go through the below web link,
http://www.iwavesystems.com/support/rma.html
Technical Support
iWave Systems technical support team is committed to provide the best possible support for our customers so that our Hardware and Software can be easily migrated and used.
For assistance, contact our Technical Support team at,
Email : support.ip@iwavesystems.com
Website : www.iwavesystems.com
Address : iWave Systems Technologies Pvt. Ltd. th nd # 7/B, 29 Main, BTM
Layout 2 Stage, Bangalore-560076, India.
INTRODUCTION
About this Guide
This document is intended as the guide for unpacking iWave’s iW-RainboW-G22D
RZ/G1E Development Platform package and setting up the test environment for
it. It also gives details about safety information and important cautions
which should adhere while using the platform.
Development Platform Overview
The iW-RainboW-G22D RZ/G1E Development Platform incorporates RZ/G1E SODIMM SOM
which is based on Renesas power effecient RZ/G1E Dual ARM Cortex A7 MPU and
SODIMM Compatible Carrier Board. This platform can be used for quick
prototyping of any high end applications in verticals like Automotive,
Industrial & Medical. The board is highly packed with all necessary on-board
connectors to validate almost complete RZ/G1E CPU features.
UNPACKING
Safety Information
-
Before unpacking and installing the Development Platform or adding devices on it, carefully read all the manuals that came with the package.
-
Place the product on a stable surface. To avoid short circuits in electronics, keep all conducting material away from the Development Platform.
-
Avoid using board in extreme dust, humidity and temperature conditions. Do not place the Development Platform in wet area.
-
Before using the Development Platform, make sure that all cables are correctly connected and the power adapter is correctly selected.
-
Make sure that Electrical Outlet where you connected the power adapter is not damaged and working fine.
-
If the power adapter is broken, do not try to fix it by yourself. To prevent electrical shock hazard,
disconnect the power cable from the electrical outlet before displacing the system. -
Don’t try to remove the RZ/G1E SOM module from the Development platform unless really required.
-
Before connecting or removing RZ/G1E SOM module from the Development platform, ensure that power cable is unplugged and ESD antistatic guidelines are followed.
Quick Start Guide
Unpacking Guidelines
Please follow the below guidelines while unpacking the iW-RainboW-G22D
Development platform.
-
Wear the anti-static wristband while unpacking and handling the Development platform to prevent electrostatic discharge.
-
Use anti-static pad/mat with proper grounding to place the Development platform.
-
Don’t touch the inside surface of the Development platform circuit board.
-
Self-grounding: Touch a grounded conductor every few minutes to discharge any excess static build-up.
-
Make sure that packing box is facing upwards while opening.
-
Make sure that the entire packing list items mentioned in Package Checklist are present.
Use ESD Protection
Static electricity can destroy electronics in the platform. Make sure to follow the ESD precautions to prevent damage to the platform and injury to the user.
iW-RainboW-G22D
Package Checklist
The iW-RainboW-G22D RZ/G1E Development Platform will be shipped with the following items:
NOTE:
Do not proceed with installation, if any of the items listed in the above checklist is missing or damaged. Contact iWave support team.
Get to know the RZ/G1E Development Platform
The iW-RainboW-G22D RZ/G1E Development Platform consists of 67mm x 37.6mm RZ/G1E SODIMM SOM and 100mmx100mm Pico-ITX form factor SODIMM Carrier Card as shown in below figure.
The iW-RainboW-G22D RZ/G1E Development Platform supports the following features.
RZ/G1E SODIMM SOM Features
CPU
| Renesas RZ/G1E MPU
Dual Core ARM Cortex A7 @ 1GHz Three-Dimensional Graphics Engines
Memory
| 512MB DDR3 (Expandable ) 4GB eMMC Flash (Expandable )
2MB SPI NOR Flash (Expandable) Micro SD Slot
Real Time Clock| RTC Controller
RZ/G1E SODIMM Carrier Board Features
Serial Interface| Debug UART through USB Micro AB Connector Data UART (SCIF5)
x 1 Port through Header
Communication Interface
| 100/1000Mbps Ethernet through RJ45MagJack USB 2.0 Host x 1 Port through Type A Connector USB 2.0 OTG x 1 Port through Micro AB Connector CAN x 1 Port through Header
Audio/Video Interface
| I2S Audio Codec with 3.5mm Audio IN and OUT jack 4.3” RGB LCD Connector with ResistiveTouch
8bit CMOS Camera
On Board Switches
| Power ON/OFF Switch Reset Switch
Boot mode setting Switch
Additional Features
| SPI Flash (MSIOF2 with SS#1) RTC Coin Cell holder
20Pin GPIO & Expansion Header
General Specification| Power Supply : 5V,2.5A Power Input Jack Form Factor : 100mm X 100mm Pico ITX
The RZ/G1E SODIMM SOM major components location are shown in the below figure. NOTE:
Refer Hardware User Guide for more details
The RZ/G1E Carrier Card major components location are shown in the below figure. Bottom View of RZ/G1E SODIMM Carrier Card
NOTE:
Refer Hardware User Guide for more details
SETTING UP THE TEST ENVIRONMENT
Getting Start
This section describes the step by step procedure to setup the test
environment for iW-RainboW-G22D RZ/G1E Development Platform.
- Read the Development Platform Documents
- Setting up the Debug port
- Power ON the Development platform
Read the Documents
Before setting up the test environment, one must read all the documents of the
iW-RainboW-G22D RZ/G1E Development Platform to know about the Platform, its
features and to get familiar with it. These documents are available in the DVD
which comes along with the iW-RainboW-G22D Package.
Below mentioned documents are available in the DVD,
- iW-RainboW-G22D Quick start Guide (This Guide)
- RZ/G1E SODIMM SOM Hardware User Guide
- RZ/G1E SODIMM Carrier Board Hardware User Guide
- RZ/G1E SODIMM SOM Software User Guide
- RZ/G1E SODIMM SOM Release Notes for Software
NOTE:
Refer DVD contents section to know about the DVD content structure and platform related document’s path.
Debug Port Setting
Please follow the below procedure to setup the Debug Micro USB of iW-RainboW-
G22D RZ/G1E Development Platform
- Connect TypeA end of USB cable to PC and Micro AB end of USB cable to Development platform’s debug Micro USB connector(J8) as shown below.
Debug Port Connection
- Install the driver for Debug USB Port in Host PC/Laptop using the below link. Drivers located at: http://www.ftdichip.com/Products/ICs/FT232R.htm
Powering ON iW-RainboW-G22D RZ/G1E Development Platform
iW-RainboW-G22D RZ/G1E Development Platform comes with 5V, 2.5A power supply with universal plugs. Please follow the below procedure to power ON the Development platform.
- Connect the 5V power supply plug to the power connector (J2) of the iW-RainboW-G22D platform as shown below and switch ON the power supply.
Power Supply Connection
- Once Power is applied to iW-RainboW-G22D RZ/G1E Development Platform, the Red Power LEDs in the RZ/G1E SODIMM SOM and carrier board will glow as shown in the above image.
WARNING:
- Do not use different power adapter other than the supplies one.
- Do not proceed with installation, if any of the Power Status LEDs are blinking or not glowing. Contact iWave support team.
Done with Test Environment
Once power is applied to iW-RainboW-G22D RZ/G1E Development Platform as
explained in the previous section, the HyperTerminal of the PC/Laptop which is
connected to the Development platform will immediately show the boot messages
of the boot loader.
iWave supports below mentioned Operating System Releases for iW-RainboW-G22D
RZ/G1E Development Platform.
Linux 3.10.31(or higher)
Depending upon the supported Operating system and boot loader on particular
delivery, the Hyper Terminal will show the boot messages as described in the
following section.
NOTE:
- Platform comes with bootable binary in default boot media.
- Make sure that all the steps mentioned in Getting Start section is followed.
Linux Test Environment
In Linux Release, U-boot boot messages will appear in Hyper Terminal as shown
below.
U-boot on Terminal
Immediately after power on, press any key in HyperTerminal to go to the U-boot
command prompt as shown below. Otherwise Linux will launch
automatically. U-boot Command Prompt
Once Linux is launched, the LCD will show the Yocto images as shown below and HyperTerminal will show the Linux Login.To Login in Linux, enter “root” in terminal and you will get the Linux command prompt as shown below. Once you get the prompt you are done with Test Environment setup on Linux delivery. NOTE: Refer Linux Software User Guide for further details.
DVD Contents
The following Figure show the DVD content structure for Linux Operating System
Release.
Linux Release DVD Contents
NOTE:
- iWave continuously improves software releases with latest kernel version.
- Contact iWave for latest software release detail.
RZ/G1E HDMI Add On Module
iWave supports HDMI Add-on Module for iW-RainboW-G22D RZ/G1E Development Platform, which supports following features.
RZ/G1E HDMI Add On Module Features
Video Features| HDMI Output through HDMI Transmitter (24bpp DU0) x 1 Port
Communication Features| CAN1 Header x 1 Port
Serial Interface Features
| Data UART RS232 Header (SCIF1 and SCIF5) x 2 Ports High Speed UART RS232
Header (HSCIF2) x 1 Port
General Specification| Form Factor : 50mm X 40mm
NOTE: For More details about HDMI Add-on Module, contact iWave Sales Team.
iWave’s other Products
iW-RainboW-G21M-RZ/G1H Qseven SOM
The RZ/G1H Qseven SOM is based on the Renesas’s RZ/G1H Octa Core processor
running at 1.4GHz ARM Cortex®-A15 MPCore cores. A single ruggedized Qseven
connector provides the carrier board interface to carry all the I/O signals to
and from the Qseven SOM. This SOM supports 2GB DDR3L RAM (Expandable) and4GB
eMMC Flash (Expandable) by default. iW-RainboW-G20M-RZ/G1M/G1N Qseven SOM
The RZ/G1M/G1N Qseven SOM is based on the Renesas’s RZ/G1M/G1N Dual Core
processor running at 1.5GHz ARM Cortex®-A15 MPCore cores. A single ruggedized
Qseven connector provides the carrier board interface to carry all the I/O
signals to and from the Qseven SOM. This SOM supports 1GB DDR3L RAM
(Expandable) and4GB eMMC Flash (Expandable) by default. HEADQUARTER:
INDIA
iWave Systems Tech. Pvt. Ltd. 7/B, 29th Main, BTM Layout 2nd Stage,
Bangalore-560076, India.
Ph: +91-80-26683700, 26781643
Fax : +91-80-26685200
mktg@iwavesystems.com
www.iwavesystems.com
JAPAN
iWave Japan, Inc.
8F-B, Kannai Sumiyoshi Building,
3-29, Sumiyoshi-cho, Naka-ku, Yokohama, Kanagawa, Japan.
Ph: +81 45 227 7626
Email: info@iwavejapan.co.jp
www.iwavejapan.co.jp
EUROPE
iWave Europe
Postbus 6197
3130 DD Vlaardingen
The Netherlands
Ph: +31 10 28403383
Email: info@iwavesystems.eu
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>