LDsystems MAILA COL Powered 4X6.5 Inch Column Speaker and Amplifier LDMAILACOL User Manual

June 9, 2024
LDSystems

LDsystems MAILA COL Powered 4X6.5 Inch Column Speaker and Amplifier LDMAILACOL

YOU MADE THE RIGHT CHOICE!

This device was developed and manufactured under high quality requirements to ensure many years of trouble-free operation. This is what LD Systems stands for with its name and many years of experience as a manufacturer of high- quality audio products. Please read these operating instructions carefully so that you can quickly and optimally use your new LD Systems product. You can find more information about LD SYSTEMS on our website WWW.LDSYSTEMS.COM

ABOUT THIS MANUAL

  • Read the safety instructions and the entire manual carefully before starting up.
  • Observe the warnings on the device and in the operating instructions.
  • Always keep the operating instructions within reach.
  • If you sell or pass on the device, be sure to also pass on these operating instructions, as they are an integral part of the product.

INTENDED USE

The product is a device for professional audio installation!
The product has been developed for professional use in the field of audio installation and is not suitable for use in households!
Furthermore, this product is only intended for qualified users with specialist knowledge of dealing with audio installations!
Use of the product outside of the specified technical data and operating conditions is considered improper use!
Liability for damage and third-party damage to persons and property due to improper use is excluded! The product is not suitable for:

  • People (including children) with reduced physical, sensory or mental abilities or lack of experience and knowledge.
  • Children (Children must be instructed not to play with the device).

EXPLANATIONS OF TERMS AND SYMBOLS

  1. DANGER: The word DANGER, possibly in combination with a symbol, refers to directly dangerous situations or conditions for life and limb.
  2. WARNING: The word WARNING, possibly in combination with a symbol, refers to potentially dangerous situations or states of life and limb.
  3. CAUTION: The word CAUTION, possibly in combination with a symbol, refers to situations or conditions that can lead to injuries.
  4. ATTENTION: The word ATTENTION, possibly in combination with a symbol, refers to situations or states that can lead to damage to property and/or the environment.
    This symbol indicates hazards that can cause an electric shock.
    This symbol indicates danger spots or dangerous situations.
    This symbol indicates danger from hot surfaces.
    This symbol indicates danger from high volumes.
    This symbol indicates supplementary information on the operation of the product.
    This symbol denotes a device that does not contain any user-serviceable parts.

SAFETY INSTRUCTIONS

DANGER:

  1. Do not open or modify the device.
  2. If your device is no longer working properly, liquids or objects have gotten inside the device, or the device has been damaged in any other way, switch it off immediately and disconnect it from the power supply. This device may only be repaired by authorized specialist personnel.
  3. For devices of protection class 1, the protective conductor must be connected correctly. Never interrupt the protective conductor. Protection class 2 devices do not have a protective conductor.
  4. Ensure that live cables are not kinked or otherwise mechanically damaged.
  5. Never bypass the device fuse.

WARNING:

  1. The device must not be put into operation if it shows obvious signs of damage.
  2. The device may only be installed in a voltage-free state.
  3. If the power cord of the device is damaged, the device must not be put into operation.
  4. Permanently connected mains cables may only be replaced by a qualified person.

DANGER:

  1. Do not operate the device if it has been exposed to severe temperature fluctuations (e.g. after transport). Humidity and condensation could damage the device. Do not switch on the device until it has reached the ambient temperature.

  2. Make sure that the voltage and frequency of the mains supply correspond to the values indicated on the device. If the device has a voltage selector switch, do not connect the device until this is set correctly. Only use suitable power cords.

  3. To disconnect the device from the mains at all poles, it is not enough to press the on/off switch on the device.

  4. Ensure that the fuse used corresponds to the type printed on the device.

  5. Make sure that appropriate measures against overvoltage (e.g. lightning) have been taken.

  6. Note the specified maximum output current on devices with a power out connection.
    Make sure that the total power consumption of all connected devices does not exceed the specified value.

  7. Only replace pluggable mains cables with original cables.

DANGER:

  1. Danger of suffocation! Plastic bags and small parts must be kept out of the reach of people (including children) with reduced physical, sensory or mental abilities.
  2. Danger from falling! Make sure the device is installed securely and cannot fall. Only use suitable tripods or attachments (especially for fixed installations). Make sure accessories are properly installed and secured. Make sure that the applicable safety regulations are observed.

WARNING:

  1. Only use the device in the manner intended.
  2. Only operate the device with the accessories recommended and intended by the manufacturer.
  3. During installation, observe the safety regulations applicable in your country.
  4. After connecting the device, check all cable routes to avoid damage or accidents, e.g. B. to avoid tripping hazards.
  5.  Be sure to observe the specified minimum distance to normally flammable materials!
    Unless this is explicitly stated, the minimum distance is 0.3 m.

ATTENTION:

  1. There is a risk of jamming with moving components such as mounting brackets or other moving components.
  2. In the case of devices with motor-driven components, there is a risk of injury from the movement of the device. Sudden device movements can lead to startle reactions.

DANGER:

  1.  Do not install or operate the device near radiators, heat registers, stoves or other heat sources. Make sure that the device is always installed in such a way that it is sufficiently cooled and cannot overheat.
  2. Do not place any sources of ignition such as burning candles near the device.
  3. Ventilation openings must not be covered and fans must not be blocked.
  4. Use the original packaging or packaging provided by the manufacturer for transport.
  5. Avoid shock or shock to the device.
  6. Observe the IP protection class and the environmental conditions such as temperature and humidity according to the specification.
  7. Devices can be continuously developed. In the event of deviating information on operating conditions, performance or other device properties between the operating instructions and the device labeling, the information on the device always has priority.
  8.  The device is not suitable for tropical climate zones and for operation above 2000 m above sea level.

ATTENTION:
Connecting signal cables can result in significant noise interference. Make sure that devices connected to the output are muted during plugging. Otherwise, noise levels can cause damage.

ATTENTION HIGH VOLUMES WITH AUDIO PRODUCTS!
This device is intended for professional use.
The commercial operation of this device is subject to the applicable national regulations and guidelines for accident prevention.
Hearing damage due to high volumes and continuous exposure: The use of this product can generate high sound pressure levels (SPL) which can cause hearing damage. Avoid exposure to high volumes.

SIGNAL TRANSMISSION VIA RADIO (e.g. W-DMX or audio radio systems, Bluetooth):
The quality and performance of wireless signal transmissions generally depends on the environmental conditions.
Influence on the range and signal stability, for example:

  • Shielding (e.g. masonry, metal structures, water)
  • High radio traffic (e.g. strong W-LAN networks)
  • interference
  • Electromagnetic radiation (e.g. LED video walls, dimmers)

All range specifications refer to free field use with visual contact without interference!

The operation of transmitters is subject to official regulations. These can vary from region to region and must be checked by the operator before commissioning (e.g. radio frequency and transmission power).

WARNING:

Devices with wireless signal transmission are not suitable for operation in sensitive areas in which radio operation can lead to possible interactions. These include, for example:

  • Hospitals, health centers or other healthcare facilities that perform patient treatments with specialized staff and equipment.
  • Class I, II and III hazardous areas
  • restricted areas
  • military facilities
  • airplanes or vehicles
  • Areas where cell phone use is prohibited

NOTES FOR PORTABLE INDOOR DEVICES

  1. Temporary operation! Event equipment is basically only designed for temporary operation.
  2. Continuous operation or permanent installation can lead to impairment of the function and premature aging of the devices.

SCOPE OF DELIVERY

Remove the product from the packaging and remove all packaging material. Check the completeness and integrity of the delivery andpleasenotify yourdistributor immediately after purchase if the delivery is not complete or damaged. Included in the scope of delivery of the product are:

  • 1x LD MAILA COL speaker column
  • 1x power cable
  • 1x M10 eyebolt
  • Operating instructions
PROPERTIES

The MAILA COL full-range column module makes MAILA truly versatile. The elegant column element with its 4x 6.5” woofers not only provides an extended low-mid range, but also includes a 4-channel DSP amplifier with 2.5 kW total power, which drives both the column itself and the MAILA SAT satellites.

In this way, MAILA sets with column module can not only be used as a ground stack variant, but also as a flown array consisting of MAILA COL and up to eight MAILA SAT – particularly useful for festivals and fixed installations. In addition, as with a classic line array, users can select different subwoofer arrangements and adapt them to the sound reinforcement requirements on site.

On the ground, the use of MAILA COL provides a further advantage: The interconnected column module allows ground stack sound reinforcement to be implemented that is significantly higher (up to 3.2 metres) than conventional systems and, with its greater throw, also enables uniform sound coverage in the far field.

With LogoLink®, LD Systems has added another innovation to MAILA. Via the free MAILA app (iPadOS), every MAILA system can be adapted quickly, easily and in detail and supplied with software updates wirelessly. Once connected, the app automatically recognises the existing MAILA components and allows the system to be optimally set up in advance as well as during an event. The clincher: The required wireless antennas are invisibly integrated into the LD logo of the MAILA COL.

MAILA APP (iPadOS)
The MAILA app for iPadOS is available free of charge in the App Store.

DANGER:
Always place the speaker system in a suitable location on a sufficiently stable, level and horizontal surface. Make sure that the speaker system cannot fall off the edge of a stage (e.g. due to vibration).

DANGER:
Overhead installation requires extensive experience, including calculation of working load limits, installation materials used and regular safety checks of all installation materials and equipment.
If you do not have these qualifications, do not attempt an installation yourself, but use the help of professional companies. There is a risk that equipment that has not been correctly mounted and secured will come loose and fall down. This can seriously injure or kill people.
The LD MAILA COL speaker column has 2 ergonomic carrying handles for comfortable transport.

To mount the speaker column on the subwoofer, insert the 4 steel bolts on the underside of the speaker column into the 4 retaining sockets of the connecting plate in the subwoofer as far as they will go. Secure the connection by screwing the M20 knurled screw on the back of the speaker column to the M20 thread of the connecting plate.

To mount the optionally available EasyMount+ flying bracket to the speaker column, insert all three steel hooks of the flying bracket into the corresponding holding sockets of the speaker column. Now push the entire flying bracket towards the back of the column. When assembling the flying bracket, make sure that the two spring-loaded safety locking bolts engage completely in the safety holes provided. Check the correct function of the locking bolts before each assembly. To release the connection, both locking bolts must be pulled upwards at the same time for safety reasons (two-hand release).

Construction And Truss Mounting

Loudspeaker column LD MAILA COL: The optimum suspension point for truss mounting is displayed after entering the corresponding data in the menu item SPLAY ANGLES under PICK . There are corresponding markings on the retaining rail of the flying bracket.
Set up the hanging point shown before mounting the flying bracket with speaker column on a truss.
To secure the MAILA COL speaker column during truss mounting, there is an M10 thread on the back of the enclosure in the recessed grip 1 .
Remove the inserted blind screw using a suitable tool. An M10 eyebolt is included in the scope of delivery of the MAILA COL. Screw the eyebolt into the now free thread and make sure it is firmly fixed. Use a suitable safety rope to secure the speaker column and also take into account the total weight of the satellite speakers mounted on the column.
Construction And Truss Mounting

NOTE
The satellites do not need to be secured by a safety rope, as the SmartLink+ connection meets the criteria for inherent safety.
However, if desired, the satellite speakers can be secured using the second M10 thread 2 on the speaker column if desired.

CONNECTIONS, CONTROLS AND INDICATORS

Connections, Controls And Indicators

Connections, Controls And Indicators

  1. POWER INPUT
    PowerCON TRUE1 Mains input socket. A suitable mains cable is included in the scope of delivery

  2. INPUT
    Balanced line input with lockable female 3-pin XLR connector.

  3. THRU
    Balanced line output for forwarding the line input signal (male 3-pin XLR socket).

  4. LC-DISPLAY
    Multifunctional graphic LC display with illumination.

  5. PUSH TO ENTER / HOLD TO MUTE
    Rotary-push encoder for navigating in the main menu and submenus and for adjusting system settings.
    Select the individual menu items in the main menu and in the submenus by turning the encoder and confirm the selection by pressing the encoder. Change a numerical value or status in a menu item by turning the encoder and confirm the change by pressing the encoder. To move up one level in the menu structure, select the arrow symbol < and confirm the selection.
    Press the encoder for about 2 seconds to mute the speaker column and again for about 2 seconds to unmute it.

  6. LEDS TO INDICATE THE STATUS OF THE UNIT
    PWR – (Power) The white indicator LED lights up when the unit is correctly connected to the mains and switched on.
    SIG – (Signal) The white indicator LED lights up when an audio signal is present at the unit.
    LIMIT – (Limiter) The yellow indicator LED lights up when the amplifier module is operated in the upper limit range. A short flash of the LED is not critical. To protect the system, an excessive signal level is gently reduced by the integrated limiter. If the limiter LED lights up for a longer time or permanently, reduce the volume level.
    PROT – (Protect) The red indicator LED lights up if the amplifier module is overloaded or overheats.
    The amplifier module is automatically muted. After reaching normal operating conditions, the unit switches back to normal operating mode after a few minutes.

  7. VENTS
    To prevent damage to the unit, do not cover the ventilation openings on the back and ensure that air can circulate freely.

  8. PUSH TO UNLOCK SAT
    On the rear upper edge of the speaker column is the release button for detaching a mounted satellite speaker.
    RETAINING BUSHES & STEEL BOLTS
    On the underside of the speaker column are the retaining sockets for the EasyMount+ flying bracket LD MAILA TMB and the steel bolts for mounting the column on the subwoofer LD MAILA SUB and also an M20 knurled screw for securing to the subwoofer.

OPERATION

NOTES

  • When switching on, all settings, such as VOLUME and EQUALIZER, are loaded as they were set before the speaker column was switched off. After a short time, the speaker column is ready for operation.
  • After about 30 seconds without any input by rotary-push encoder, the display system leaves lower levels in the menu structure and the main display with the VOLUME selection is automatically shown.

DISPLAY MAIN DISPLAY
In normal operation, the main display is activated, showing the main menu, the set delay and the number of satellites used. The Bluetooth status, the volume level (LVL) and the amplification (VOL) are displayed graphically.
If the top segment of the level meter lights up red, this indicates that the input stage is being operated above the distortion limit (clip). Reduce the output level of the feed device (e.g. mixing console) until the clip segment no longer lights up and the speaker column reproduces audio signals without distortion.

VOLUME
To adjust the level of the speaker column, select VOLUME in the main menu , confirm, then set the desired value from -40 dB to +10 dB and confirm again.
Display Main Display

Mute: Press the encoder for about 2 seconds to mute the speaker column and again for about 2 seconds to unmute it (at all menu levels).
Display Main Display

SPLAY ANGLES

Mounting on subwoofer:

To enable the automatic calculation of the optimal spreading angles of the satellites, the rotation of the display must be set correctly.
ROTATION menu item, status: standing

The number of satellite speakers used is automatically detected by the column electronics. To enter the relevant data of the audience area and the height at the measuring point, select SPLAY ANGLES in the main menu, confirm, then select the corresponding submenu item and confirm again.

Enter at Sat. Height , enter the height of the bottom edge of the lowest satellite measured from the audience stand and the distance from the array system to the back row of the audience (Coverage) in metres. At Seated enter standing (Seated OFF) or seated audience (Seated ON). Now the optimal spreading angles for each satellite are automatically displayed. To exit the menu level, select the arrow symbol and confirm the selection.
The spread angles are set manually on the satellite speakers. The correct setting of the indicated spreading angles is a prerequisite for the optimal sound distribution on the indicated listening area.
Display Main Display

Truss mounting:
To enable the automatic calculation of the optimal spreading angles of the satellites and the optimal hanging point of the EasyMount+ flying bracket (for traverse mounting), the rotation of the display must be set correctly.
ROTATION menu item, status: flying.

The number of satellite speakers used is automatically detected by the column electronics. To enter the relevant data of the audience area and the height at the measuring point, select SPLAY ANGLES in the main menu, confirm, then select the corresponding submenu item and confirm again.

For truss mounting, enter the following under Sat. Height, enter the height of the top edge of the uppermost satellite measured from the audience stand and the distance from the array system to the back row of the audience (Coverage) in metres. At Seated enter standing (Seated OFF) or seated audience (Seated ON). Now the optimal spread angles for each satellite and the hang point PICK for the EasyMount+ flying bracket are automatically displayed. To exit the menu level, select the arrow symbol and confirm the selection.

The spread angles are set manually on the satellite speakers. Setting up the hanging point of the EasyMount+ flying bracket is also done manually. The correct setting of the indicated spreading angles and the suspension point is a prerequisite for the optimal sound distribution on the indicated listening area.
Splay Angles

EQUALIZER
The integrated DSP (Digital Signal Processor) has a powerful 10-band fully parametric equaliser.
Select EQUALIZER in the main menu and confirm the selection.
LDsystems MAILA COL Powered 4X6.5 Inch Column Speaker and Amplifier
LDMAILACOL Setup Interface

The function of the equalizer bands 1 and 10 can optionally be set as fully parametric or as low-shelf (band 1, LS) or hi-shelf (band 10, HS).

EQ ON / OFF

NR| FREQ| Q| GAIN
1| 30 – 20000| 0.1 – 10.0 / LS| -20 – +10
2| 30 – 20000| 0.1 – 10.0| -20 – +10
3| 30 – 20000| 0.1 – 10.0| -20 – +10
4| 30 – 20000| 0.1 – 10.0| -20 – +10
5| 30 – 20000| 0.1 – 10.0| -20 – +10
6| 30 – 20000| 0.1 – 10.0| -20 – +10
7| 30 – 20000| 0.1 – 10.0| -20 – +10
8| 30 – 20000| 0.1 – 10.0| -20 – +10
9| 30 – 20000| 0.1 – 10.0| -20 – +10
10| 30 – 20000| 0.1 – 10.0 / HS| -20 – +10

To set the frequency in hertz under FREQ, the Q factor or the functioning of bands 1 and 10 under Q and the gain in dB under GAIN, select the corresponding column in the desired equaliser band (NR 1 – 10), confirm, set the value as desired and confirm again. The selected value is displayed with a white background.
The EQ bands can be deactivated individually by selecting and confirming the band number. Instead of a tick symbol, an X is now displayed and the values in the corresponding band appear greyed out.
Select and confirm again to activate the band.
The entire equaliser can be deactivated by selecting the EQ line, confirming, then selecting OFF and confirming again. All values in the equaliser are now greyed out. To activate the equaliser, select ON and confirm. To exit the menu level, select the arrow symbol and confirm the selection.

DELAY
To delay the audio signal, select DELAY, confirm, then select the desired submenu item and confirm again. The value or status can now be set as desired, confirm each entry.
LDsystems MAILA COL Powered 4X6.5 Inch Column Speaker and Amplifier
LDMAILACOL Setup Interface

DELAY TIME x.x ms / m / ft Set delay time in the selected delay unit
DELAY UNIT ms Delay unit milliseconds
m Delay Unit Meter
ft Delay unit foot
TEMPERATURE x °C / °F Set the ambient temperature in the selected

temperature unit
TEMP. UNIT| °c| Temperature unit Celsius
°F| Temperature unit Fahrenheit

To exit the menu level, select the arrow symbol and confirm the selection.

POLARITY
To set the polarity of the audio signal, select POLARITY, confirm, then select the desired status and confirm the selection.

LDsystems MAILA COL Powered 4X6.5 Inch Column Speaker and Amplifier
LDMAILACOL Setup Interface

POLARITY normal Normal polarity
inverted Inverted polarity

ROTATION

To set the rotation of the display, select ROTATION, confirm, then select the desired status and confirm the selection.

To enable the automatic calculation of the optimal spreading angles of the satellites and the optimal hanging point of the EasyMount+ flying bracket (for truss mounting), the rotation of the display must correspond to the mounting type.

  • Mounting on spacer bar: ROTATION standing
  • Truss mounting (180° rotation): ROTATION flying

LDsystems MAILA COL Powered 4X6.5 Inch Column Speaker and Amplifier
LDMAILACOL Setup Interface

SETTINGS
To enter the system settings menu, select SETTINGS and confirm the selection. Then select the desired submenu item and confirm the selection.

ROTATION standing Upright
flying Truss assembly

SETTINGS
To enter the system settings menu, select SETTINGS and confirm the selection. Then select the desired submenu item and confirm the selection.

PIN LOCK| 8

i Enter PIN code to LOCK

| Protect the amplifier module from accidental and unauthorised operation by activating the lock function.

Enter a 4-digit PIN and confirm the entry.

Access can now only be made after entering the PIN.

Reset PIN: Hold down the encoder when switching on.

---|---|---
BLUETOOTH| OFF | Bluetooth deactivated.
ON | Bluetooth activated, access to the system via tablet app enabled.
DISPLAY| Brightness| Adjust the display brightness from 10% to 100%.
Screensaver| active| Deactivation of the display illumination after approx. 1 minute without input via rotary-push encoder.
inactive| Display illumination permanently on.
RESET| FACTORY DEFAULT
| Restore factory settings: Select RESET and confirm.

MAILA APP

Download the MAILA app, which is available free of charge in the App Store, onto your tablet and install it. Activate Bluetooth in the system settings of the active MAILA components. Also  activate Bluetooth in the system settings of your tablet and start the MAILA app. The MAILA components with activated Bluetooth within range are now automatically displayed in the MAILA app after a short time.

FIRMWARE UPDATE

Use the MAILA app to check whether a new firmware is available for your unit. Start the update procedure via MAILA App. Make sure that there is a stable wireless connection between the device and the tablet and do not switch off the device or the tablet until the update procedure is complete. Cancelling the update procedure may cause the unit to malfunction. The MAILA app for iPadOS is available free of charge in the App Store.

INDICATION-LED

The speaker column has a white indicator LED on the front behind the front grille. This can be activated for easy identification of the speaker column using the MAILA app. The MAILA app for iPadOS is available free of charge in the App Store.

OPTIONAL ACCESSORIES

LDMAILAFC2 (Flight case for 4x SAT, 1x COL, 1x Easy Mount+) LDMAILATMB (Easy Mount+ flying bracket)

CARE, MAINTENANCE AND REPAIR

To ensure the proper functioning of the unit in the long term, it must be regularly maintained and serviced as required. The need for care and maintenance depends on the intensity of use and the environment. We generally recommend a visual inspection before each commissioning. Furthermore, we recommend that all the maintenance measures listed below be carried out every 500 hours of operation, or at the latest after one year in the case of less intensive use. Defects caused by insufficient care may result in limitations of the warranty claims.

CARE (CAN BE CARRIED OUT BY THE USER)

WARNING! Before carrying out any maintenance work, the power supply and, if possible, all
device connections must be disconnected.
NOTE! Improper care can lead to impairment or even destruction of the unit.

  1. Housing surfaces must be cleaned with a clean, damp cloth. Make sure that no moisture can penetrate the unit.
  2. Air inlets and outlets must be regularly cleaned of dust and dirt. If compressed air is used, make sure that damage to the unit is prevented (e.g. fans must be blocked for this case).
  3. Cables and plug contacts must be cleaned regularly and freed from dust and dirt.
  4. In general, no cleaning agents or agents with an abrasive effect may be used for maintenance, otherwise the surface finish is likely to be impaired.
  5. Units should generally be stored in a dry place and protected from dust and dirt.

MAINTENANCE AND REPAIR (BY QUALIFIED PERSONNEL ONLY)

DANGER! There are live components in the unit. Even after disconnecting the mains connection, residual voltage may still be present in the unit, e.g. due to charged capacitors.
SymbolNOTE! There are no assemblies in the unit that require maintenance by the user.
NOTE! Maintenance and repair work may only be carried out by specialist personnel
authorised by the manufacturer. If in doubt, contact the manufacturer
NOTE! Improperly performed maintenance work may affect the warranty claim.

DIMENSIONS (mm)

Dimension

TECHNICAL DATA

Item number LDMAILACOL
Product type MAILA Column
Type Powered
Low/mid driver dimensions 4 x 6.5 “
Woofer size 16.51 mm
Woofer magnet Neodymium
Woofer brand Custom-made
Woofer voice coil 2 “
Woofer voice coil (mm) 50 mm
Amplifier Class D
System Power (RMS) 2500 W
Frequency response (-6dB) 105 Hz – 500 Hz
Protection circuits limiter, over-current, thermal overload
Input impedance 20000 Ohm(s)
Controls Rotary/push encoder
Indicators Indication LED, LC display, Limit, Power, Protect, Signal
Line inputs 1
Line input connectors XLR
Line outputs 1
Line output connectors XLR
Speaker output connections SmartLink+®
Wireless Connectivity LogoLink® for App Control
Operating voltage SMPS
Power consumption (max.) 800 W
Operating voltage 100 V AC – 240 V AC, 50 – 60 Hz
Operating Temperature 0 – 40 °C
Relative Humidity < 80 %, not condensing
Cabinet material Die-cast aluminum
Cabinet surface Powder-coated
Cabinet construction Bass Reflex
Mounting 3 x M8, 4 x Pin, Easy Mount+
Handles 2
Overall Height incl. Pins 1028 mm
Width 205 mm
Depth 354 mm
Weight 34.44 kg

DSP Characteristic
Bit depth AD/DA converter| 24 bit
Sampling frequency| 48 kHz
Bluetooth
Bluetooth version| 4.2
Bluetooth transmission power| 9 dBm
Bluetooth frequency range| 2402-2480 MHz

DISPOSAL

Packing :

  1. Packaging can be fed into the recycling system via the usual disposal channels.
  2. Please separate the packaging according to the disposal laws and recycling regulations in your country.

Device:

  1. This appliance is subject to the European Directive on Waste Electrical and Electronic Equipment as amended. WEEE Directive Waste Electrical and Electronical Equipment. Old appliances and batteries do not belong in household waste. The old appliance or batteries must be disposed of via an approved waste disposal company or a municipal waste disposal facility. Please observe applicable regulations in your country!
  2. Observe all disposal laws applicable in your country.
  3. As a private customer, you can obtain information on environmentally friendly disposal options from the dealer from whom the product was purchased or from the relevant regional authorities.

Batteries and rechargeable batteries:

  1. Batteries and rechargeable batteries do not belong in household waste. Batteries and rechargeable batteries must be disposed of via an authorised disposal company or amunicipal disposal facility.
  2. Observe all disposal laws and regulations applicable in your country.
  3. As a private customer, you can obtain information on environmentally friendly disposal options from the dealer from whom the product was purchased or from the relevantregional authorities.
  4. Appliances with batteries or accumulators that cannot be removed by the user must be handed in at a collection point for electrical appliances.

MANUFACTURER DECLARATION

MANUFACTURER’S WARRANTY & LIMITATION OF LIABILITY
Adam Hall GmbH, Adam-Hall-Str. 1, D-61267 Neu Anspach / Email Info@adamhall.com / +49 (0)6081 / 9419-0.
For our current warranty terms and limitation of liability see:
https://cdn-shop.adamhall.com/media/pdf/MANUFACTURERS DECLARATIONS_LD_SYSTEMS.pdf. In the event of service, please contact your sales partner

UKCACONFORMITY
Hereby, Adam Hall Ltd. declares that this product meets the following guidelines (where applicable)
Electrical Equipment (Safety) Regulations 2016
Electromagnetic Compatibility Regulations 2016 (SI 2016/1091)
The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulation 2012 (SI 2012/3032)
Radio Equipment Regulations 201 7(SI 2016/2015)

UKCA- DECLARATION OF CONFORMITY
Products that are subject to Electrical Equipment(Safety)Regulation 2016, EMC Regulation 2016 or RoHS Regulation can be requested at info@adamhall.com. Products that are subject to the Radio Equipments Regulations 2017 (SI2017/1206) can be downloaded from www.adamhall.com/compliance/

FCC STATEMENT

  1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
    (1) This device may not cause harmful interference, and
    (2) This device must accept any interference received, including interference that may cause undesired operation.

  2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

RADIATION EXPOSURE STATEMENT
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.

  • Increase the separation between the equipment and receiver.
    Connect the equipment into an outlet on a circuit different from that to which the receiver

  • is connected.

  • Consult the dealer or an experienced radio/TV technician for help.

EU DECLARATION OF CONFORMITY
Adam Hall GmbH hereby declares that this radio system type complies with Directive 2014/53/EU.
The full text of the EU declaration of conformity is under the following Internet address available: www.adamhall.com/compliance/ Misprints and mistakes, as well as technical or other changes are reserved!

  Adam Hall GmbH | Adam-Hall-Str. 1 | 61267 Neu-Anspach | Germany
Phone: +49 6081 9419-0 | adamhall.com
Adam Hall Ltd. | The Seedbed Business Centre | SS3 9QY Essex | UKMALIA
icon

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals