Ocean LED 013010 Wi-Fi DMX Touch Panel Controller Kits User Manual

: June 6, 2024
: Ocean LED

Table of Contents

Preface
Overview
Installation
Operation
Troubleshooting
Warranty
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

LED 013010 Wi-Fi DMX Touch Panel Controller Kits
2021
INSTALLATION & OPERATION MANUAL Ocean LED 013010 Wi-Fi DMX Touch
Panel Controller Kits WWW.OCEANLED.COM

LIGHT .YEARSAHEAD .
OceanLED MANUAL/CONTROLLERS/WiFi DMX TOUCH/REVISION 0.1

Preface

READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL
WARNINGS
Before installing your DMX Controller, read and follow all warning notices and instructions which are included. Failure to follow safety warnings and instructions can result in property damage, severe injury or even death.
Before installing your DMX Controller, check local laws for restrictions regarding the use of colored lights in your area.
Salt is an inherently corrosive material. Natural and man-made surfaces are susceptible to corrosion and deterioration when used in and around saltwater. Some combinations of plastic and polymer products are impervious to saltwater corrosion, however, screws and fasteners used for the installation must be of a marine-grade type stainless steel or equivalent and monitored annually to ensure the controller remains in service for years to come.
Never Use Solvents! Cleaners, fuel, and other products that may contain strong solvents, such as acetone, attack many plastics greatly reducing their strength and can cause irreversible damage.
Units are not waterproof. You must mount in a dry location. When installing, be sure that the controller fits
the area and secures to the mounting location using the appropriate hardware before installing.

DANGER
RISK OF ELECTRIC SHOCK OR ELECTROCUTION

This unit must be installed by a licensed or certified electrician in accordance with all applicable local codes and ordinances. Improper installation will create an electrical hazard that could result in death or serious injury to installers, or others due to electrical shock, and may also cause damage to property. Always disconnect the power to the light at the circuit breaker before servicing the light. Failure to do so could result in death or serious injury to a serviceman, or others due to electrical shock.

PRETEST
Always test the system prior to installation. Failure to do this may result in additional installation time and could invalidate the warranty.
IMPORTANT NOTICE
Attention Installer: This manual contains important information about the installation, operation, and safe use of this product. This information should be given to the owner and/ or operator of this equipment.
WARRANTY COVERAGE
Please refer to www.oceanled.com/downloads for a full warranty statement.

Overview

Units are not waterproof. You must mount in a dry location. When installing, be sure that the controller fits the area and secures to the mounting location using the appropriate hardware before installing.

TOOLS AND MATERIALS

Never use power tools. Hand tightens only!

Drill & Drill Bits.
Screw Driver, Phillips #2
Wire Strippers.
Tape measure and Ruler or Straight Edge.
Marking Utensil (Pencil, Sharpie Magic Marker, etc)

FINDING THE MOUNTING LOCATION

The mounting location needs to be carefully selected to ensure the unit will not be exposed to moisture.
Ensure that the ambient temperature where the unit is mounted cannot exceed 45°C – Note that engine compartments can easily exceed this.
The chosen location requires access to mains power, space for the routing of the DMX cable to the driver boxes, and also an Ethernet connection to a Wi-Fi router / LAN Wi-Fi for the Wi-Fi controller if the Wi-Fi function is required.

For DC power installations please contact OceanLED for advice

SPECIFICATIONS

Ready to use (pre-loaded with scenes).
Glass Touch Panel with graphical color display
Micro SD Card (32Gb Max)
6-7V DC / 100-240V AC (With Adapter)
Environment IP20, Temp -10˚C to 45˚C
Certifications: CE, EMC, ROHS, ETL
Dimensions 146x106x11mm
Weight 247g

Installation

CONNECT THE WIRES (EXPLORE E6 & E7)

Connect the control cable to the green connector (as below)
• DMX Ground = Black
• DMX – = Brown
• DMX + = Yellow
• Red wire (Unused, do not connect)
Connect power via the AC/DC adapter provided.
• Power DC + = Black/White Stripe
• Power DC – = Black
CONNECT THE WIRES (PRO SERIES)
Connect the control cable to the green connector (as below)
• DMX Ground = Brown & Brown/White (two wires)
• DMX – = Orange
• DMX + = Orange/White
Connect power via the AC/DC adapter provided.
• Power DC + = Black/White Stripe
• Power DC – = Black

MOUNT IN A DRY LOCATION

Plug the green connector block into the rear of the DMX Wi-Fi Touch Panel Controller.
For Wi-Fi plug the local ethernet cable into the rear of the DMX Wi-Fi touch panel controller (Ensure the correct RJ45 port is used):
Mount the backplate of the interface on the preferred dry mounting location.
Close the unit by clipping the front panel onto the backplate.

FINALISE YOUR INSTALLATION (EXPLORE E6 & E7)

Always test the system BEFORE the boat goes back into the water. Typical OceanLED light installs require the boat to be hauled out of the water to replace light units.
The DMX standard recommends a maximum of 32 devices to be connected in one chain. If the installation requires more lights than this, please contact OceanLED for advice.

If Wi-Fi is required connect the Ethernet cable from the back of the controller panel into a suitable Wi-Fi router or Wi-Fi-enabled network. (The controller is DHCP enabled as standard so should be detected by the network once powered).
Connect the control cable to the control input of the first Explore E6 light. Then connect a control link cable to the next, and so on up to the last light in the chain.
Fit the supplied terminator to the output of the last E6 light. See the following example of the connections:
Always test the system BEFORE the boat goes back into the water. Typical OceanLED light installs require the boat to be hauled out of the water to replace light units.
The DMX standard recommends a maximum of 32 devices to be connected in one chain. If the installation requires more lights than this, please contact OceanLED for advice.
If Wi-Fi is required connect the Ethernet cable from the back of the controller panel into a suitable Wi-Fi router or Wi-Fi-enabled network. (The controller is DHCP enabled as standard so should be detected by the network once powered).
Connect the DMX controller DMX output cable to the DMX input of the first driver box. The DMX output of this box should be connected to the input of the next, and so on up to the last driver in the chain.
Fit the supplied terminator to the output of the last driver box. See the following example of the connections:

Operation

POWER / SCENE SELECTION

Power on the unit by touching the top center button.
Select the required scene by using the buttons under the ‘Select Area’ buttons below the display to select the required area and select the scene by touching the left/right arrows on either side of the display. Once the required scene is selected, play that scene, press the ‘Play Scene’ button.

PRE-PROGRAMMED SCENES – EXPLORE

Explore Dual White / Blue

Troubleshooting

Wi-Fi DMX Touch Panel Controller

Problem| Check| Cause|

Fix

DMX controller does not power on| Check Power to Controller is on| No Power| Connect Power
Power OK| Check Connections
Check Connections to controller faceplate| Connected incorrectly| Correct Connections
Connected OK| Contact Warranty Department
Lights do not respond to the controller and/or random flickering of lights/colors| Check DMX
connection is daisy-chained between a controller and all drivers| Not connected correctly| Correct cabling connections
Check all other cables are connected
correctly and are not damaged| Not connected correctly| Correct connections
Damaged cable| Replace Cable
Check Terminator is fitted to last driver box| Terminator not fitted| Fit terminator
Terminator fitted| Contact Warranty Department
WiFi not working (only applicable to wi-fi
model)| Check Ethernet cable is connected into the back of the controller panel correctly.| Not connected| Reconnect cable
Check the controller panel is recognized on the connected
network.| Controller not visible| Try re-booting the network hub and controller panel.
Check connected network WiFi is functioning correctly| WiFi not functioning| Resolve issue with network WiFi
WiFi network OK| Contact Warranty Department

Warranty

Please remove this page and keep for your files For technical assistanc e:
Europe:service@oceanled.com
The Americas:warranty@oceanledusa.com

Warranty Serial Code(s):

© 2021 Ocean LED Marine LTD
All Rights Reserved Specifications are subject to change without notice.
Trademarks are the property of Ocean
LED Marine LTD| Ocean LED Marine LTD
Unit 1 Jacknell Road
Dodwells Bridge Industrial EstateHinckley,
Leicestershire LE10 3BS
United Kingdom
Tel: +44 (0) 1455 637505
Fax: +44 (0) 1455 238553
sales@oceanled.com| Ocean LED USA LLC
778 South Military Trail
Deerfield Beach Florida
FL 33442-3025
USA
Tel: +1 954.523.2250
Fax: +1 954.523.2249
sales@oceanledusa.com
---|---|---

www.oceanled.com

Documents / Resources

| Ocean LED 013010 Wi-Fi DMX Touch Panel Controller Kits [pdf] User Manual
013010 Wi-Fi DMX Touch Panel Controller Kits, 013010, Wi-Fi DMX Touch Panel Controller Kits
---|---