PALOVUE TWD1802 Wireless Earbuds Instruction Manual

PALOVUE TWD1802 Wireless Earbuds

PRODUCT OVERVIEW

PAIRING

1. Please place both lWS into the charging case and close the lid (about 3 seconds).
2. Please open the lid of the charging case, and long-press the reset button inside the case(about 8-12 seconds), please note that you need to release your hand as soon as all 4 white lights above the reset button are on.
3. Then you will see the light blinking in the right touch area(about 2 seconds later), which means SportSound has been reset and ready for pairing.
   4. Please continue to keep the lid open, then go to Bluetooth settings and select “Palovue SportSound” on your Bluetooth audio device.
   – Once successful, there are two prompts: “pairing successful” and “connected’.
   – Once reconnected, there is a prompt ‘connected”.
   • The Earbuds LED lights will flash when the MIC is enabled during a call.

WEARING

Steps:
To achieve the most comfortable fit and sound for your TWS, take time to test out the various tip sizes to find the best fitting size. It is normal to use differently sized tips in each ear.

• Step 1: Place the earbuds into your each ear, like picture 1.
• Step 2: Whirl the earbuds to be comfortable, like picture 2.
• Step 3: Put on the ear hooks and adjust to fit your ears, ensure the Mic 2 align with mouth, like picture 3.

CHARGING

• The lWS will start charging once they are placed into the charging case and the lid closed.
•  The charging case LED will indicate the charging status:
  · Charging: Solid red light on case.
  · Fully charged: Solid green light on case.

To shortly press the button on the charging case, it will indicates the power of the case.

PALOVUE® TWS APP

The Palovue TWS App lets you do the following:

•  Customize the touch control of your SportSound TWS Earbuds.
•  Update your earbuds when new features and improvements are available.
• Open/Close the Noise Cancelling Mode.

TOUCH CONTROL (FACTORY DEFAULT)

TROUBLESHOOTING

Factory Reset:

•  Place both TWS in the charging case and dose the lid.
•  Open the charging case, press & hold the case button until the four case LED lights started blinking (about 8-12 seconds).
•  The SportSound TWS has been reset and is ready to pair.

WARM TIPS

1. When there is no sound on one side of both earbuds, please follow the above steps to factory reset and then ignore the SportSound earbuds Of any) from the Bluetooth list of the phone and re-pair it
2. Please clean the earplugs and charging post’s pogo pins regularly with alcohol to avoid poor contact due to dirt.
3. If the other party finds your voice too low during the call, please try to adjust the wearing position of the earbuds.
4.  SportSound earbuds can be set in the SportSound APP to turn on/off the noise-reduction mode, and the first call after setting will take effect. (Note that the settings during the call cannot take effect immediately)
5. After you get the product, please Please pick up the earbuds and remove a film between the charging pins and earbuds(The film is used to prevent the battery from running out during the shipping process), and then put the earbuds back into the charging case for charging, which can ensure that the product can be used effectively

SUPPORT

If there is any questions or issues, please contact with PALOVUE Support Team, we will respond to you in 24 hours.
Email: support@palowe.com
www.palowe.com

FCC WARNING

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment.
Notes: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Note: If shielded cables or special accessories are required for compliance, a statement must be induced which instructs the user to employ them, for example, Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Manufacturer. Foneric Electronics Co.,Ltd. Made in China
FCC ID: 2ARYG-SPORTSOUND

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>