Nikon NIKKOR Z 24-50mm f4-6.3 Lens User Manual

NIKKOR
NIKKOR Z 24-50mm f/4-6.3
User’s Manual
NIKON CORPORATION
Printed in Japan
CT0C01(64)
7MMA4464-01  △

| |
---|---|---

User’s Manual

Before using this product, please read these instructions carefully. You will also need to consult the camera manual

• This lens is intended exclusively for use with mirrorless cameras featuring a Nikon Z mount.

For Your Safety

To prevent damage to property or injury to yourself or to others, read “For Your Safety” in its entirety before using this product.
Keep these safety instructions where all those who use this product will read them.

WARNING: Failure to observe the precautions marked with this Icon could res undeath or severe injury.
CAUTION: failure to observe the precautions marked with this icon could result in injury or property damage.

**WARNING**

• Do not disassemble or modify this product.
  Do not touch internal parts that become exposed as the result of a fall or other accident.
  Failure to observe these precautions could result in electric shock or another injury.

• Shou ld you notice any abnormalities such as the product producing smoke, heat, or unusual odors, immediately disconnect the camera power source. Continued operation could result in fire, bums, or another injury.

• Keep dry.
  Do not handle it with wet hands.
  Failure to observe these precautions could result in fire or electric shock.

• Do not use this product in the presence of flammable dust or gas such as propane, gasoline, or aerosols.
  Failure to observe this precaution could result in explosion or fire

• Do not directly view the sun or other bright light sources through the lens.
  The failure to observe this precaution could result in visual impairment

• Keep this product out of reach of children.
  Failure to observe this precaution could result in injury or product malfunction. In addition, note that small parts constitute a choking hazard. Should a child swallow any part of this product, seek immediate medieval attention.

• Do not handle with bare hands in locations exposed to extremely high or low temperatures.
  Failure to observe this precaution could result in burns or frostbite.

CAUTION

• Do not leave the lens pointed at the sun or other strong light sources. Light focused by the lens could cause fire or damage to the product’s internal parts When shooting ~klit subjects, keep the sun well out of the frame. Sunlight focused into the camera when the sun is close to the frame could cause ‘”

• Do not leave the product where it will be exposed to extremely high temperatures, for an extended period such as in an enclosed automobile or in direct sunlight.
  Failure to observe this precaution could result in fire or product malfunction.

• Do not transport cameras or lenses with tripods or similar accessories attached.
  Failure to observe this precaution could result in injury or product malfunction

Notices for Customers in the U.S.A.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this deviee may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

Federal Communications Commission (FCC) Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However. there is no guarantee that interference will not occur in a
pa particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:

• Reo rent or relocate the receiving antenna
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/television technician for help.

CAUTIONS
Modifications
The FCC 1tquiies user to be notified that any cl1<111g~s or mudifJCillions out to this device that is not expressly approved by Nikon Corporation may void the user’s
authority to operate the equipment. Nikon Inc., 1300 Walt Whitman Road,
Melville, New York 11747-3064, U.S.A.
Tel.: 631-547-4200

Notice for Customers In Canada
CAN ICES-3 B / NMB-3 B

Using the lens

Parts of the lens: Names and Functions
Refer to the diagram on the left edge of this sheet

See B
3 Focal length scale| Determine the appropriate focal length Mien zooming the lens In or out|
4 Focal length mark
5 Control ring| Autofocus mode selected: In autofocus mode, rotate the ring to adjust a setting such as Focus (WA) or Aperture assigned using the camera. For more information, see the description of Custom controls/Custom control assignment/Custom controls (shooting) in the camera manual.|
Manual focus made selected: Rotate the ring to focus.| _
6 Lens mounting mark| Use when mounting the lens on the camera.| see A
7CPU contacts| Used to transfer data to and from the camera.| —
8 Lens hood*| Lens hoods block stray light that would otherwise cause flare or ghosting. They also serve to protect the lens.| See C
9 Lens hood lock mark| Use when attaching the lens hood
10 Lens hood alignment -`!5 mark
11 Lens cap (front cap)| —| —
12 Lens cap (rear cap)| —| —

A Attachment and Removal
Attaching the lens

1.  Turn the camera off, remove the body cap, and detach the rear lens cap.
2. Position the lens on the camera body, keeping the mounting mark on the lens aligned with the mounting mark on the camera body, and then rotate the lens counterclockwise until it dicks into place.

Removingfflelem

1.  Turnthecameraoff.
2. Press and hold the lens release button while turning the lens clockwise.
3. Before Use
   The lens is retractable and must be extended before use. Rotate the zoom ring as shown until the lens dicks into the extended position. Pictures can only be taken when the focal length mark points to positions between 24 and SO on the focal length scale.

To retract the lens, rotate the zoom ring in the opposite direction, stopping when you reach the ● position on the focal length scale. If the camera is turned on with the lens retracted, a warning will be displayed. Extend the lens before use

C Attaching and Removing the Lens Hood
Align the lens hood mounting mark with the lens hood alignment mark 1 and then rota re rhe hood 2  until the mounting mark is aligned with the lens hood lock mark 3
When attaching or removing the hood, hold it near the lens hco::I alignment mark (e J and avoid gripping the front of the hood too tightly. The hood can be reversed
and mounted on the lens when not in use.

Using the lens on Cameras with a Built-in Flash
Shadows will be visible in photos where the light from the built-in flash is obscured by the lens or lens hood. Remove the lens hood before shooting.
When the lens Is Attached
The focus position may change if you turn the came ra off and then on again after fo­ cus ing. If you have focused on a pre-selected location while waiting for your subject to appear, we recommend that you do not turn the camera off until the picture is taken

Precautions for Use

• Do not pick up or hold the lens or camera using only the lens hood

• Keep the CPU coo tacts clean

• Replace the lens caps when the lens is not in use.

• To protect the interior of the lens, store it out of direct sunlight.

• Do not leave the lens in humid locations or in locations in which it may be exposed to moisture. Rusting of the Internal mechanism can cause irreparable damage.

• Do not leave the lens next to open flames or in other extremely hot locations. Ex­treme heat could damage or warp exterior parts made from reinforced plastic.

• Rapid changes in temperature may cause damaging condensation inside and outside the lens. Before taking the lens from a warm to a cold environment or vice versa, place
  it is in a bag or plastic case to slow the change in temperature.

• We recommend that you place the lens in its case to protect it from scratches during transport

Lens Care

• Removing dust is normally sufficient to clean the glass surfaces of the lens, Smudges, fingerprints, and other oily stains can be removed from the lens surface Use a soft, clean cotton cloth or lens cleaning tissue lightly dampened with a small amount of ethanol or lens cleaner. Wipe gently from the center outwards in a circular motion, taking care not to leave smears or touch the ~ns with your fingers. – Never use organic solvents such as paint thinner or benzene to clean the lens.
• Neutral Color (NC) filters (available separately) and the like can be used to protect the front lens element.
• If the lens will not be used for an extended period, store it in a cool, dry location to prevent mold and rust. Do not store in dire<t sunlight or with naphtha Of camphor
  mothballs.

Accessories

•  Supplied Accessories

• LC-52B lens cap(front cap)

• LF-Nl LensCap(rear cap)
  Compatible Accessories, HB-98 Lens Hood

• CL-C4LensCase
  – 52mmscrew-filters E:!iiFilters

• Useonlyonefilteratatlme.
  – RemO’lelhelenstoo:lt:.!foreattachlngfiltersorrota ti ngcircu large)la riliogfilters.

Specifications

aspherical elements)
Angle of view| •FX format: 84° — 47°
•DX format: 61° — 31° 30′
Focal length scale| Graduated in millimeters (24, 28, 35, 40, 50)
Focusing system| Internal focusing system
Minimum focus
distance| 0.35 m (1.15 ft) from the focal plane at all zoom positions
Maximum reproduction ratio| 0.17x (50 mm zoom position)
Diaphragm blades| 7 (rounded diaphragm opening)
Aperture range| •24 mm zoom position: f/4 — 22
•SO mm zoom position: f/6.3 — 36
Filter attachment
size| 52 mm (P = 0.75 mm)
Dimensions| Approx. 73.5 mm (2.9 in.) maximum diameter x 51 mm (2.1 in.)
(distance from camera lens mount flange when the lens is retracted)
Weight| Approx. 195 g (6.9 oz)

Nikon reserves the night to change the appearance, specifications, and performance of this product ar any time and without prior notice.

Reta in this International Warranty with proof of purchase (bill of sale) for your records
Nikon Corp. LENS ONE YEAR WORLDWIDE LIMITED WARRANTY
(Excluding the Continental United States, Alaska, Hawaii, Puerto Rico, and U.S. Virgin Islands) Welcome to the worldwide family of Nikon owners. Your Nikon equipment has been manufactured to the highest quality standards by NIKON CORPORATION, Tokyo, Japan. This limited warranty entitles the original consumer purchaser to international warranty protection in accordance with these terms and conditions. It affords the original consumer purchaser warranty protection outside the Continental United States,  Alaska, Hawaii, Puerto Rico, and the U.S. Virgin Islands. Such warranty coverage is supplemental to and not in lieu of the United States Nikon Inc. Lens One Year USA Limited Warranty which is received by the original consumer purchaser with the Nikon product. The Nikon product except for batteries is warranted by NIKON CORPORATION, Tokyo, Japan to be free from defects in materials or workmanship for a period of one (1)year from the date of purchase. To find an international Nikon Service Facility see: http://imaging.nikon.com/products/imaging/worldwide/index.htm. During this period any one of the international service facilities will service without charge any parts or assembly of parts found to be defective in materials or workmanship, subject to the following limitations and exclusions:
1. This warranty extends to the original consumer purchaser only and is not assignable or transferable.
2. This warranty shall not extend to any product which has been subject to misuse, alteration, abuse, negligence, accident, or unauthorized repair or has had its serial number altered or removed.
The above warranty is expressly in lieu of all other warranties expressed or implied including but not limited to any implied warranty of merchantability or fitness for a particular purpose, except to the extent prohibited by applicable law, in which event the duration of any implied warranty shall be limited to one (1) year from the date of purchase or such longer period as may be required by applicable law. Under no circumstances shall Nikon be liable for consequential, indirect, special, direct, exemplary, punitive, or incidental damages arising out of or related to any breach of this warranty or any other claim regarding this product, including but not limited to, claims of negligence, strict liability or breach of contract.
Some jurisdictions, such as states or provinces, do not allow (a) limitations on how long an implied warranty lasts or (b) the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from jurisdiction to jurisdiction.
In order to obtain international service, the original consumer purchaser should return the Nikon product, either in person or addressed to the Warranty Department of any authorized service facility listed on the above website, together with proof of purchase and proof of purchase date (bill of sale) and this warranty. The original consumer purchaser in returning this product must prepay all shipping and insurance costs to the service facility.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>