NEC E988 98 Inch Ultra High Definition Commercial Display User Manual

NEC E988 98 Inch Ultra High Definition Commercial Display

Product Information

• Model: E988
• Setup Manual: Included
• Product Warranty: This product can only be serviced in the country where it was purchased.

Installation

• The product warranty does not cover damage caused by improper installation.
• Usage Environment: Avoid locations with extreme temperatures and humidity.

Installation Steps

1. Install the remote control batteries
2. Connect external equipment
3. Connect the supplied power cord
4. Turn on the power for the monitor and the external equipment. Switch on the monitor power first.

Note: Remember to save your original box and packing material to transport or ship the monitor.

Securing Personal Information

Before transferring or disposing of the monitor, clear personal data by performing the network reset function.

FCC Information

• Use of Cables: Use the provided specified cables with this product to avoid interference with radio and television reception.
• Warning: The Federal Communications Commission (FCC) does not allow any modifications or changes to the unit except those specified by Sharp NEC Display Solutions of America, Inc. in this manual.
• Compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If not installed and used in accordance with the instructions, this equipment may cause harmful interference to radio communications.

Contents

1. Depending on the country where the LCD monitor is shipped to, AAA batteries are not included in the box contents.

Setup Manual

NOTE: This product can only be serviced in the country where it was purchased.

1. The contents of this manual may not be reprinted in part or whole without permission.
2. The contents of this manual are subject to change without notice.
3. Great care has been taken in the preparation of this manual; however, should you notice any questionable points, errors or omissions, please contact us.
4. The image shown in this manual is indicative only. If there is inconsistency between the image and the actual product, the actual product shall govern.
5. Notwithstanding articles (3) and (4), we will not be responsible for any claims on loss of profit or other matters deemed to result from using this device.
6. This manual is commonly provided to all regions so they may contain descriptions that are pertinent for other countries.

Installation

• The product warranty does not cover damage caused by improper installation. Failure to follow these recommendations could result in voiding the warranty.
• WARNING: Please refer to the “Important Information”.
• When transporting, moving, or installing the product, please use as many people as necessary (at least four) to be able to lift the product by the four handles without causing personal injury or damage to the product.
• In order to install the monitor on ceiling or wall, use a lifting device attached to the eyebolts. Do not lift the product only by people. The product may fall causing personal injury.
• DO NOT use this monitor on the floor with the table top stand. Please use this monitor on a table or with a mounting accessory for support.
• CAUTION: Avoid locations with extreme temperatures and humidity. The usage environment for this monitor is as follows. Failure to do so could damage to the product or lead to fire or electric shock.
• The operating temperature: 0 °C to 40 °C/32 °F to 104 °F/ humidity: 20 to 80% (without condensation)
• The storage temperature: -20 °C to 60 °C/-4 °F to 140 °F/ humidity: 10 to 90% (without condensation)

1. Install the remote control batteries
2. Connect external equipment CAUTION: Use the provided specified cables with this product so as not to interfere with radio and television reception. For USB and mini D-Sub 15-pin, please use a shielded signal cable with ferrite core. For HDMI and RS-232C, please use a shielded signal cable. Use of other cables and adapters may cause interference with radio and television reception.
3. Connect the supplied power cord
4. Turn on the power for the monitor and the external equipment Switch on the monitor power first.

NOTE: Remember to save your original box and packing material to transport or ship the monitor.
Securing personal information: Personally identifiable information, such as IP addresses, may be saved on the monitor. Before transferring or disposing of the monitor, clear this data by performing the network reset function

FCC Information

CAUTION: Use the provided specified cables with this product so as not to interfere with radio and television reception.
For USB and mini D-Sub 15-pin, please use a shielded signal cable with ferrite core.
For HDMI and RS-232C, please use a shielded signal cable.
Use of other cables and adapters may cause interference with radio and television reception.
WARNING: The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by Sharp NEC Display Solutions of America, Inc. in this manual.
Failure to comply with this government regulation could void your right to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult your dealer or an experienced radio/TV technician for help.

If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions.
The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.

SUPPLIER’S DECLARATION OF CONFORMITY

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

• U.S. Responsible Party: Sharp NEC Display Solutions of America, Inc.
• Address: 3250 Lacey Rd, Ste 500
• Downers Grove, IL 60515
• Tel. No.: 630-467-3000
• Type of Product: LCD Monitor
• Equipment Classification: Class B Peripheral
• Model: E988

Registration Information

• The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI Trade dress, and HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
• USB Type-C® and USB-C® are registered trademarks of USB Implementers Forum.
• All other brands and product names are trademarks or registered trademarks of their respect

(For Customers in the U.K.)

IMPORTANT

• The wires in this mains lead are colored in accordance with the following code:
• GREEN-AND-YELLOW: “Earth”
• BLUE: “Neutral”
• BROWN: “Live”
• As the colors of the wires in the mains lead of this apparatus may not correspond with the colored markings identifying the terminals in your plug proceed as follows:
• The wire which is colored GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or colored green or green-and-yellow.
• The wire which is colored BLUE must be connected to the terminal which is marked with the letter N or colored black.
• The wire which is colored BROWN must be connected to the terminal which is marked with the letter L or colored red.
• Ensure that your equipment is connected correctly. If you are in any doubt consult a qualified electrician.
• WARNING: THIS APPARATUS MUST BE EARTHED
• ENERGY STAR® is a program run by the U. S. Environmental Protection Agency (EPA) and U. S. Department of Energy (DOE) that promotes energy efficiency.
• This product qualifies for ENERGY STAR in the “factory default” settings and this is the setting in which power savings will be achieved. Changing the factory default picture settings or enabling other features will increase power consumption that could exceed the limits necessary to qualify for an ENERGY STAR rating. For more information on the ENERGY STAR program, refer to e nergystar.gov.

Service & Support in Europe

Please contact:

• Sharp NEC Display Solutions Europe GmbH.
• Landshuter Allee 12-14, D-80637 München
• Phone: + 49 (0) 89/99699-0
• Fax: + 49 (0) 89/99699-500
• For the latest information please see https://www.sharpnecdisplays.eu/p/hq/en/home.xhtml
• Data is subject to change without notice.
• Sales Office List for Asia/Pacific
• For the latest information please see https://www.sharp-nec-displays.com/global/products.html

Documents / Resources

| NEC E988 98 Inch Ultra High Definition Commercial Display [pdf] User Manual
E988, E988 98 Inch Ultra High Definition Commercial Display, 98 Inch Ultra High Definition Commercial Display, Ultra High Definition Commercial Display, High Definition Commercial Display, Commercial Display, Display
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>