Lucci decor 231342 Brix Square Up and Down Wall Bracket Instruction Manual

231342 Brix Square Up and Down Wall Bracket
**Instruction Manual

**

Installation Instructions

BRIX SQUARE UP AND DOWN WALL BRACKET

SKU# 231342, 231343
Rated Voltage 220-240V~ 50Hz
Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation and use of this luminaire. Please keep instructions for future reference.

Warranty

• This luminaire is covered by a 5-year warranty. The warranty is from the date of purchase, not the date of installation.
• If the luminaire is not assembled and installed by a licensed electrician the warranty will be void.
• Please retain the proof of purchase and evidence of installation by a licensed electrician for any warranty inquiries.
• The warranty will be void if there is any damage due to improper usage or modification of the luminaire.
• Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.

Installation Requirements

• Must be assembled and installed by a licensed electrician.

• All wiring and installation of the luminaire must adhere to the latest local and national wiring rules. eg. AS/NZS 3000 Electrical installations.

• This luminaire is a Class I product and must be earthed during wiring and installation.

• This luminaire is rated IP65. This must be maintained during wiring and installation.

• Replace any cracked protective lamp shade to maintain IP rating when using this luminaire.

• Do not exceed the maximum wattage rating.

• Select a suitable location for installation:
  – This luminaire is rated against water penetration to IP65 standards, which is against low-pressure jets of water from all practicable directions. This must be maintained during installation.
  – The mounting point must support 2 times the weight of the luminaire.

• Take care not to pull any electrical wires during unpacking as this may damage the connection.

• Lay out all the components on a smooth surface and make sure there are no components missing before assembling.
  If parts are missing, return the complete product to the place of purchase for inspection or replacement.

• Check whether the luminaire has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.

• Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.

Installation Directions

1. Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material. If assembly is required, place the luminaire on a smooth non-scratch surface.

2. Remove the mounting bracket from the luminaire by loosening the screws with the Allen key provided. Fig. B.

3. Remove the covers from the luminaire by loosening the screws with the Allen key provided. Fig. B

4. Use the mounting bracket as a template to mark the screw positions on the wall. Fig. C

5. Install the mounting bracket onto the wall by using appropriately sized mounting screws and anchors. Ensure the screws and anchors used are suitable for the mounting surface and the surrounding environment. Fig. C

6. Connect the main supply wire to the terminal block. Ensure the wires are secure and no bare wires are exposed.
   Mains Supply Wire
   Earth ­ Yellow/Green
   Neutral -Blue
   Live- Brown
   Luminaire Wire / Terminal Block
   Yellow/Green or
   Blue or N
   Brown or L
   NOTE: A non-corrosive bead of silicone MUST be applied before installation onto the wall ensuring that no water can run down into the cabling.

7. Install the globes (not included) into the lamp holders. Do not exceed the maximum wattage rating.

8. Install the luminaire onto the mounting bracket and secure it by tightening the screw. Fig. D

9. Install the covers back onto the luminaire and secure them by tightening the screws. Fig. D

10. After the installation, switch on the luminaire to test and enjoy your new lighting product.

Safety Tips

• Always ensure the power is OFF and the luminaire has cooled down before performing any maintenance, cleaning, changing the globe, or making any adjustment to the luminaire.
• To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the power.
• The luminaire must not be used if the protective shield has been cracked. Replace any cracked protective shield before using the luminaire.
• Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.
• To clean, wipe with a damp clean cloth. Do NOT soak or immerse the luminaire in water or other liquids

Specifications

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>